TOP5TopBest

Пікірлер

@jeromed685 3 күн бұрын

Quite useless!

@asmrhairandmore-j5v 15 күн бұрын

👍🏼

@raiderfan3789 16 күн бұрын

Year?

@Theboss894 15 күн бұрын

The year for the car model is 1998.

@alleverythingasmr-wq6sy Ай бұрын

I was looking at a rav 4 used years ago.

@SeekingHim-k5j Ай бұрын

🔆

@Stevenhou Ай бұрын

2AZ FE engine 2.4 Liter is the engine that is known to burn oil

@dbona4445 Ай бұрын

That is not the coolant temperature sensor it is the oxygen sensor

@devinmoore9877 Ай бұрын

On the map sensor where does the hose/ tube that connects to it run to and is this 4 cylinder le model ?

@youtute7135 2 ай бұрын

At WHAT point did you interact with the MAF sensor?!?!?! We only see you unhook and dismount a connector and bracket?? You say absolutely nothing during the video. Less than helpful lolol

@dulichphanthietmuine 3 ай бұрын

Very impressive!.✌️

@Theboss894 2 ай бұрын

Thanks for the encouragement.

@FactsForU481 3 ай бұрын

I found the air filter and pressure valve information helpful, thanks!

@Theboss894 2 ай бұрын

I am glad you found this information helpful.

@7ismersenne 3 ай бұрын

I own a Toyota Camry 2005 v6 Altise - base grade model. This car has done 360k km (Australia). The engine is quiet and uses very little oil between its 10000 km services. Transmission changes smoothly with no issues. The body has a few rattles but nothing serious (no rust). Brakes are smooth and powerful. All this sounds like a advertising blurb but really, these Toyotas are great cars. Look after them and they'll last a long, long time.

@jeffsullivan3101 3 ай бұрын

Don't buy any after market sensors from local auto parts stores. Toyotas do not like aftermarket sensors especially map sensors. If you can't find OEM parts from toyota then try to get Denso or Asin parts. They are the OEM parts without the Toyota box. RockAuto usually has what you need.

@dickbiggerstaff5729 4 ай бұрын

Bent axle shaft!? Not usually. Check CV joints.

@SebastianBlix 4 ай бұрын

nah.

@LawpickingLocksmith 4 ай бұрын

OMG there are engines built for ethanol. It stops the knock, this was known before they even added lead, the most deadly genocide on humanity.

@RT22-pb2pp 5 ай бұрын

1 hard to find good one. 2 if found to costly. 3 folks realized how great 5th gen is. 4 they rarely break so even at 337k miles cannot justify getting lower mileage one. 5 hell I am out of bad things on 5th gen camry😅

@kerrybryant5880 7 ай бұрын

Im pretty sure the sensor the red arrow is pointing at in the last 15 secs is actually an O2 sensor...

@Theboss894 6 ай бұрын

Oh, so close! The part is just beside the O2 sensor, but you're right on target. 🙂

@franknam1 7 ай бұрын

that is not an Audi a4.... wtf

@Theboss894 7 ай бұрын

Hey @franknam1, thanks for pointing that out! While it might not be an Audi A4, it's from the same manufacturer and related to the car we were discussing. We appreciate your attention to detail. Thanks for watching and engaging with our content!

@JackM-zm3fs 8 ай бұрын

Totally unexpected, I just realized that Mario updated his favorite way to tackle ED and it's crazy! Although what he previously talked about was pretty decent, it was difficult to follow, I just go'ogled the latest in Mario's Thunderous Erections, it's so much simpler and potent now!

@jio8520 8 ай бұрын

Hello, im pretty handy on most car's. Do much on my pristine 06 300 limited. I took over my mom's 2000 Camry with the 2.2. Great engine. Still only 79000. Been getting to know the engine. My question is most map sensors can be cleaned unless you have crazy mileage on them. I upgraded to a k&n air filter. I figured clean the sensor while I was at it. Did the throttle butterfly to keep the carbon out. But i noticed this map sensor seems closed up. No wire to spray with the map cleaner. Am i missing something? Car idles perfect so no reason to change the part with low mileage. Just wondering if it can be sprayed. Thanks! Lol I'm doing an edit. Looking more into it. The spray goes into the hole where the vacuum hose goes. Most map sensors I saw pop into the manifold for a twist pull out. Then spray in or just replace. The vacuum hose threw me off. Have to say best four cylinder ever made! Nice video 👍

@Theboss894 8 ай бұрын

Id clean it with contact cleaner, and follow up with dielectric grease to seal where the pins are. ( Not intake manifold hose)

@jio8520 8 ай бұрын

@@Theboss894 yes thanks. I do have the CRC map sensor cleaner on hand. That should do the trick as far as the hole part on the sensor where carbon can build. Yes also have electronic spray. But no issues with the connection. But won't hurt lol. Thanks!