Пікірлер
@lethalalias
@lethalalias 6 сағат бұрын
Thank you Brad for another great video.
@DennisMurphey
@DennisMurphey 14 сағат бұрын
Very helpful, I have one very much like that and it has not started in 2 years imagine that. I had problems before and bought a new carb form sears for $90. With that carb it was running rich and pulsing, but it ran. Now I feel so I could rebuild the original carb for bet operation. Where can we get rebuild kits and what else should I worry about? Try to find that ASPEN 4 gas that sounds great. We do not have so much snow anymore so I think a case of that is worth. worst case just put in your car right? Thanks Again Great video well done camera man and very informative. Dennis in Virginia
@donmarinelli3407
@donmarinelli3407 14 сағат бұрын
This is a great video! Thanks Heres what i got, just started a 3 x 28in And auger is spinning without squeezing control handle. Any suggestions?
@notachance3444
@notachance3444 16 сағат бұрын
Unfortunately that large back plate with the throttle control goes all the way around to the right where my electric start is and I don’t know how to get it off. This has become a complete clusterfuck of a job and it might lead me to drink again I’m that pissed. These snowblowers are complete dogshit and whoever the lead engineer was needs to be slapped in the face.
@anthonyprice4069
@anthonyprice4069 18 сағат бұрын
too the point
@mysterytour5983
@mysterytour5983 18 сағат бұрын
Wow one of the best video i have seen! Details of the tools needed ,Clear explainations, super tone of voice Bravo!
@mikef3481
@mikef3481 18 сағат бұрын
Very Informative! Thanks you for the video.
@bigmackstruckstop9213
@bigmackstruckstop9213 19 сағат бұрын
Thanks Brad for another learning moment,I started my JD D110 tractor up warm up and added stabilize ran around in the yard for a bit,will catch you on the next one and merry Christmas to you and yours😊
@cjorges
@cjorges 20 сағат бұрын
Great video! Tried checking this but looks fine on my mower. It still turns but doesn’t crank. Any other ideas??
@SmokingDeWalt
@SmokingDeWalt 21 сағат бұрын
Great video! I have that exact same generator but mine is pull start only. Do you know if a kit is available to convert mine to electric start? Thanks
@polosandoval
@polosandoval Күн бұрын
What's interesting is the Tecumseh technicians manual states when using the electric starter, don't prime the engine.
@SPMech1
@SPMech1 Күн бұрын
👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍
@jeffkingery2562
@jeffkingery2562 Күн бұрын
Thank you so much for posting this video. It helped me a lot. I appreciate your expertise.
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
I'm glad you found it helpful and thanks for the kind comment! Please give this video a thumbs up and share my channel to help it grow. It would be greatly appreciated!
@jeffkingery2562
@jeffkingery2562 23 сағат бұрын
@@JohnsonsSmallEngines Done!
@coyotetrickster3947
@coyotetrickster3947 Күн бұрын
Thank goodness you mentioned checking the float for fuel, I'm have a borrowed snowblower that suddenly started leaking fuel from the carb like crazy. Your video is very easy to follow for a beginner like me, I love how organized and labeled everything is, keep doing what you do!
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
I'm glad you were able to figure out your issue! Thank you for the kind comment. Will do :)
@colterface
@colterface 2 күн бұрын
Amazing video! Exact carb that I have. Bought an old Ariens 7524 brand new from Habitat for $550. Couldn’t figure out why it kept lugging until all of the sudden gas kept pouring out. Opened the bowl and found that the float was entirely filled with gas! Such a great video.
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
I'm glad it was helpful and thank you for the kind comment. I hope the new old machine treats you well after your repair! Please give this video a thumbs up, subscribe if you haven't already and share my channel to help it grow. It would be greatly appreciated!
@Bill-k4z
@Bill-k4z 2 күн бұрын
How to put a new drive belt on
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
This may be what you are looking for. kzbin.info/www/bejne/hWLSiYCjeJaIhcU
@johnstratton5637
@johnstratton5637 2 күн бұрын
which way does the heated handle grip switch have to be to make them heat up
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
Most machines that have the heated grips will show On/Off sometimes tucked up where you cannot see it very well but if you have a I and a O? I is on and O is off.
@davidbertinato
@davidbertinato 2 күн бұрын
Thanks Brad. Was able to remove the carburetor on my blower thanks to your guidance. Looks like the O ring that sits on top of the fuel reservoir is missing. Anything I can use in a pinch to get me up an running right away.
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
If you are talking about the carburetor bowl gasket? I never needed to actually try to improvise. I would never let a machine go out that way and I have multiple bad carburetors to pick from in a pinch. The bowl gasket is a tough one being most are rubber. you may be able to use a silicone that would need to be gas proof but if you need to go and get the sealer. I would recommend going to your local small engine repair shop and see if they may have a used one from another carburetor that is the same as yours. Take your carburetor with you so they can match it up.
@davidbertinato
@davidbertinato Күн бұрын
@@JohnsonsSmallEnginesThanks Brad. Actually found the O ring sitting in the wheel well of the left wheel. Must have fallen off without me noticing. It feels a little stiff and dry, but I’ll go with it until I get to a small engine repair shop. Now if I can only get the engine to stop surging.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 23 сағат бұрын
The surging normally is a blockage in the carburetor. Why did you remove the carburetor? I have a video on how to rebuild it if you need it.
@defan2105
@defan2105 3 күн бұрын
one of my friends puts his carb jets and tubes in GooGone, which gets the sticky garbage out. Thoughts? I still would follow up with carb cleaner but not a bad idea.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
I personally never used that product and never will. I normally use a ultrasonic cleaner. I have been showing my videos without using my ultrasonic cleaner (I do not think the normal person would have one and should not need to purchase one) showing how most carburetors can be cleaned without using much, just what you may have on hand.
@defan2105
@defan2105 2 күн бұрын
@@JohnsonsSmallEngines so true, being 63 and learning how to do this, I seem to be fixing my neighbor's stuff more and more. So far two lawnmowers, 1 snow blower, and soon a generator that revs up and down but runs. But maybe he won't trust me with it and take it to a real shop but I can tell you it is his carb...he only runs it ever few years. Thank you for being a blessing and helping us all.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 2 күн бұрын
Sounds like you’re a busy person! Tell your neighbor with the surging generator he can just run it with the choke in the half position or place the choke where the engine will not surge. Yes, you are correct. Your neighbor needs a rebuild or replace the carburetor. You should not run the generator plugged into the house while it surges. Not good for anything plugged into it as the electric will also surge unless the generator is an inverter. Just a little heads up:) Take care!
@defan2105
@defan2105 2 күн бұрын
@@JohnsonsSmallEngines good to know! He was running his refrigerator and sump pumps, and I forget what else. Now that you say it, it seems so obvious! I took small engines as a single class back in 1979 so rusty is an understatement. Nothing like a color blind person doing repairs but my favorite thing was rebuilding carburetors. (I retired from 22 years of repairing microscopes).
@robertmcmahon2744
@robertmcmahon2744 3 күн бұрын
Just getting ready to do this to a 9hp Tecumseh on a 26" Craftsman blower. Thanks for the part# of the drain gasket. No other video has given it. Your camera person does an outstanding job on showing clearly every move you make. Love your videos, so Peace out and God Bless.😎✌🖖🙏
@robertmcmahon2744
@robertmcmahon2744 3 күн бұрын
Hey, was going to send a couple of bucks you way for the video However, KZbin doesn't have a "$Thanks$" botton set up for you, like other people's video's have. You should find out why not!! Let me know when you get a "$Thanks$" botton set up. Thanks
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
Im glad it was helpful and thank you for the kind comment! Take care :)
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
Thank you for the heads up! I'm not a tech computer guy but I was able to turn on the "thanks button". I thought it was suppose to show up on all of my videos but I don't see it on my end. Check it out and let me know.
@dwoodbec
@dwoodbec 3 күн бұрын
THANK YOU, amazing and so easy to follow.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
I'm glad it was helpful and your back up and running. Please give this video a thumbs up, subscribe if you haven't already and share my channel to help it grow. It would be greatly appreciated!
@gamingMattR
@gamingMattR 3 күн бұрын
Fantastic video. Very easy to follow. Saved me a repair bill. Thank you!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
Glad to hear your up and running and saved $$! Thank you for the kind comment. Please give this video a thumbs up and share my channel to help it grow. It would be greatly appreciated!
@bobasfatt
@bobasfatt 3 күн бұрын
I'm not too familiar with small engines, haven't ever successfully taken apart and fixed a carburetor before (tried once with an old mower). But this video was straightforward and easy to follow along with, and I was able to follow along easily. I took apart the carburetor and saw an incredible amount of crud. Cleaned it all out, reassembled and it runs better than it ever has, even when it was brand new. Thank you for a quality tutorial, this was well made and was a huge help in turning a frustrating day into a successful one!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
I’m glad it was helpful and you were able to get your machine up and running again! Thank you for the kind comment and supporting my channel.
@iamahermit
@iamahermit 3 күн бұрын
Thanks, i'm going to try and drain the old fuel from the carb and hope it goes. I don't think i'm smart enough to take the whole carb out ha
@agoogleuser5830
@agoogleuser5830 3 күн бұрын
Thank you
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
You’re very welcome!! I’m glad it was helpful and thank you for the kind words.
@nhorstman1440
@nhorstman1440 3 күн бұрын
Thank you sir, your great!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
I'm glad you found the video helpful! and thank you for the kind comment. Please give this video a thumbs up and share my channel to help it grow. It would be greatly appreciated!
@DeborahCorbett-tx5br
@DeborahCorbett-tx5br 4 күн бұрын
This was extremely helpful, thankyou
@JohnsonsSmallEngines
@JohnsonsSmallEngines 4 күн бұрын
I’m glad it was helpful and thank you for the kind comment. Please give this video a thumbs up and share my channel with your friends to help you grow. It would be greatly appreciated!
@erickpeterson537
@erickpeterson537 4 күн бұрын
Nice little advice, just leave the vise grips on the choke plate I would of set it down and fought it later
@warrens.6229
@warrens.6229 4 күн бұрын
Excellent and helpful videos. BTW, I was delighted to discover on the 3x30 Cub Cadet snow blower the carburetor came off without removing a stud or fussing with the handle, just slips off.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
So simple and it was a huge upgrade to everyone working on these.
@gibo1971
@gibo1971 4 күн бұрын
Great video, thanks for your instruction. I was dreading changing the belt as had nothing but problems with the d130 ( although I got it cheap second hand) I got the John Deere belt and it is heaps better than I got from the workshop that fitted the last one. Now I just have to figure out how to start it without having to pour fuel down the carb.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 4 күн бұрын
I’m glad this video is helpful! what is the making and model of the engine on your tractor? I may have a video on showing you how to adjust the choke if that may be your issue.
@poxxie9
@poxxie9 4 күн бұрын
What an incredible video. I appreciate your effort in making such a great step by step directions. Thank you.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 4 күн бұрын
I’m glad it was helpful and thank you for the kind comment. Please give this video alike and share my channel to help it grow. It would be greatly appreciated.
@bradmcfalls4169
@bradmcfalls4169 4 күн бұрын
I’ve seen a ton of KZbin videos and it doesn’t get better than this one. Wow!! Excellent job. I’m trying to get the in laws snow blower going. Exact same situation not starting for two years. Just hoping I don’t have to take everything apart like this. All my years I’ve never seen green gas. 😂 Again great video!!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 4 күн бұрын
I’m glad my videos have been helping you and thank you for the kind comment. I hope you were able to get the machine running!
@daedalus45b
@daedalus45b 4 күн бұрын
Great tutorial! Thanks for presenting this!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 4 күн бұрын
I'm glad you found it helpful and thank you for the kind comment! Please give this video a thumbs up and share my channel to help it grow. It would be greatly appreciated!
@StudCity718
@StudCity718 4 күн бұрын
Anyone know if this rebuilt kit works for all tecumseh carbs? I have a Yard Machines 8hp 24" model 31AS6FEE729. Thanks
@JohnsonsSmallEngines
@JohnsonsSmallEngines 4 күн бұрын
If you have a genuine Tecumseh carburetor not adjustable this kit will work. You will just need to get the correct emulsion tube.
@StudCity718
@StudCity718 3 күн бұрын
​​@@JohnsonsSmallEnginesthanks. I really only need the little gasket at minute 31:40. Mine leaks gas from there. I ordered a Rotary kit. Hope it comes with that part.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 3 күн бұрын
If your talking about the drain push spring loaded gasket? The part number is Tecumseh 27554. I would also get the bowl gasket Part# Tecumseh 30356. You should be able to go to your local lawn and garden repair center and pick up (1) each. I would call to make sure they have them in stock before heading over. After market gaskets are not good.
@StudCity718
@StudCity718 3 күн бұрын
@JohnsonsSmallEngines I will do that if the rebuild kit doesn't come with it. Thanks alot brother. I really appreciate it.
@kaylibounsavath6400
@kaylibounsavath6400 4 күн бұрын
😊
@AustinReavesCousin
@AustinReavesCousin 4 күн бұрын
The manual says I can only use a 15 amp, 125 volt extension cord. The one I have is 10/125. Can I still use that or is it a bad idea to do so?
@TheRancher03
@TheRancher03 5 күн бұрын
These are very good Riding Mowers. Even though My Craftsman twin cylinder can run circles around the Pony, it has a broken fancy transmission that's hard to maintain and only 6 years old. The 15 year old Pony will outlast the Craftsman replacement.
@jonbradley4789
@jonbradley4789 5 күн бұрын
WoW! That was cool.
@mikegrimes5688
@mikegrimes5688 5 күн бұрын
Nice video, very well presented will follow up on those heat shrink soldering connectors, as my soldering is crap. I have a craftsman mower, that is shorting on wires within the engine harness, not sure how or what to look for from there. I turn key to run and fuse blows, I disconnect engine harness plug and fuse stays on and service hours display is on too. Mower was going after a long layoff, but then just stopped with blades engaged, haven't been able to start since, battery replaced. Any ideas would be appreciated. Thanks.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 5 күн бұрын
Is it still blowing fuses when the engine harness is connected? If yes, check the electronic fuel shut off wiring. The hot wire may be grounding out. If you have an electric PTO clutch? also check the wiring. If you have a manual PTO. Check to make sure the handle is all the way off. There is a safety switch that must be depressed before the engine will start.
@mikegrimes5688
@mikegrimes5688 3 күн бұрын
@@JohnsonsSmallEngines thnx for your help, I traced it to a faulty ignition coil on one of the cylinders
@brianolson7114
@brianolson7114 5 күн бұрын
great job, dude.
@JohnsonsSmallEngines
@JohnsonsSmallEngines Күн бұрын
Thanks! Glad you liked it.
@kevinhintz1903
@kevinhintz1903 5 күн бұрын
Damn impressive 👍
@JohnsonsSmallEngines
@JohnsonsSmallEngines 4 күн бұрын
Ty!
@markpowell4082
@markpowell4082 5 күн бұрын
See last comments by me... I replaced the carb and new gaskets and it is running worse, hardly at all unless I choke it on full. It looks like I need a pro to look at it. I used OEM parts. However, before I take it in, can you adjust the carb? I know it is something with the carb.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 5 күн бұрын
There are no adjustments on the carburetor. Check to make sure your gaskets are in there correct positions from carburetor to manifold and carburetor to air cleaner box.
@markpowell4082
@markpowell4082 5 күн бұрын
@ Thank you for your help… I am gonna put the old carb on and see how it is running…. And probably have a pro look at it. Thank you once again!
@robertcollins6155
@robertcollins6155 5 күн бұрын
Is the drive belt idler pulley adjustable
@JohnsonsSmallEngines
@JohnsonsSmallEngines 5 күн бұрын
Not on this one. The tension on both drive belts are spring tension only.
@g.fortin3228
@g.fortin3228 5 күн бұрын
Thank you for this ! got me out of a jam
@JohnsonsSmallEngines
@JohnsonsSmallEngines 5 күн бұрын
I’m glad it was helpful and your back up and running!! Please give this video a thumbs up and share my channel to help it grow. It would be greatly appreciated!!
@g.fortin3228
@g.fortin3228 5 күн бұрын
@@JohnsonsSmallEngines ohh.. I did !
@RichardYoung-m7t
@RichardYoung-m7t 5 күн бұрын
What is the belt number?
@danielbyer644
@danielbyer644 6 күн бұрын
Thanks for all the extra info!! Really appreciate this.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 5 күн бұрын
I’m glad it was helpful and thank you for the kind comment. Please give this video a thumbs up, subscribe if you haven’t already and share my channel to help it grow. It would be greatly appreciated!
@RyderDean
@RyderDean 6 күн бұрын
Found your channel looking for help in exactly this application. I have a Remington snowblower from Menards with the exact same engine. Ive already ordered a replacement carb but keep putting it off. Snow is coming soon and after watching your video, I'm sure it will go well. Your video is very well done and informative. I subscribed on the spot and look forward to watching more.
@JohnsonsSmallEngines
@JohnsonsSmallEngines 6 күн бұрын
I’m glad this video was helpful and thank you for subscribing! Just take your time and you should be fine! Thank you for watching the kind comment
@lorimacfarlane1210
@lorimacfarlane1210 6 күн бұрын
Thanks! Great video for a newbie!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 6 күн бұрын
I’m glad it was helpful and thank you for the kind comment. Please give this video a thumbs up, subscribe if you haven’t already and share my channel with your friends to help it grow! It would be greatly appreciated.
@vindra11
@vindra11 6 күн бұрын
This was a HUGE help! I deff would have broke something getting that shaft off. You da man!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 6 күн бұрын
I’m glad you found this video before something broke! Lol. I’m glad it was helpful and thank you for the kind comment.
@ArtHilliker
@ArtHilliker 6 күн бұрын
MA MAN !! Thank You !!
@JohnsonsSmallEngines
@JohnsonsSmallEngines 6 күн бұрын
I’m glad it was helpful and thank you for the kind comment!