Hello, I'm interested in which pin connector you used for the connection (blue and white wire).

thanks for your video. It's very helpful. I have a question. How did you attach the camera to the rear bumper? did you have to remove the bumper.?

Can we use plastic paint and primer with this mechine

And hotspot temperature? Is very important

Not bad results - though I for one will not be using an angle grinder taped to a stick just 10 inches from open toed sandals...

thanks i hope yiou are sure on the pad thickness ...will double check in any case !=]

Can it be done on Opel mokka X 2017 year. LC7F Intellilink R4 is the "radio". It has 20pins connector. Is there a diagram?

Poor instruction.

Can we have a chat about something it favor? There are so many things that I will say but KZbin won't allow me So where is it easy for us to chat about your channel because there are so many things that is going to favor you!

It’s possible to do this as well for the front camera?

Are you can do this for the parking sensor as well, for example my insignia don’t have a parking sensor, but if I want install how I can do, the parking module how I can connect to the car?

Hello, be careful when you open it. The keyboard foil is connected to the computer center with two small, delicate cables. The plug connections on these cables are delicate and not very stable. These cables are dimensioned so that they can only accommodate an opening of about 45 degrees between the keyboard foil and the computer board. If you open it more than 45 degrees without thinking, it can happen (like it did to me) that the cables suddenly slip out of their slots and you have to puzzle and fumble to put everything back together correctly. I think that's a bit unreasonable for changing a battery.

First big job 😂

When driving up thrm ranps don’t they move whike your driving up them

The cup is a viscosity meter haha 😂😂

I really wanted to see everything you were doing on the injectors. But your camera was in the wrong place.

Do you know what cables are speaker cables in that model ?

Any idea how much water for emulsion??

Do I need to install software with OBD?

Hi can you tell me please how you unlock reverse camera function and where did you bought yellow video cable ( how much totally cost you Thanks

Good morning, can you send me the connection diagram for the Insignia rear-view camera? I don't understand the connection with HMI. Is the white wire connected to the plug on the inside or outside? then the camera cable on the HMI side to just the RCA plug? THANK YOU 

Hi where did you get the yellow wire from? Thank you

Don't we need to code it at the end ?

How to get the camera video to automatically change when reversing. How the switching is carried out automatically? Thank

i cant seem to get the 2 ribbon cables back in ?

That thing you are using to scoop the paint out is to measure the thickness of the paint.

thanks for the tutorial

Sorry bei Funktioniert das überhaupt nicht mit der pin Belegung fahre Opel Insigna Sport Tourer 2016

What if after replacing the sollenoid valve (with ove rpressure savety), the steam still comes out through the over pressure valve? I cannot find the pressure switch in the system. It's a Tefal GV7556

Is this vauxhall insignia 2016 1.6 diesel?

Hi it's very good video, but i didn't understand only one thing, 5.01 min of the video you speak about 4 and 5 pin, so what is blue and what is white, i mean in yellow wear? I mean i need to do that important yellow wear.

I have a 2014 Insignia OPC/VXR and a did everything that you did but my camera doesn't work. They told me that I have to programming my system to recognised my camera. I don't understand why is your camera is working and mine is not?

I have the same iron, all the lights are flashing and nothing works, what do you suggest to try cleaning the boiler tank

Could not have just been the Seals? These modern injector are known for playing up and its just worn Seals.

Is it good ?asus x555l?

You also do not connect the positive of the video cable to the HMI module, I understand that the red cable must go to the positive of the module, why don't you do it, can you clarify for me?

You don't connect the red wire of the video cable, I see that you haven't used it, and I wonder why? Isn't it necessary to connect it to the reverse gear positive? thank you

Good video, I would've removed the little screw for the fuel filter to avoid any mess as you get a replacement screw anyway, the fuel filter was overtightened when refitting it doesn't need to be that tight, should be careful as you can snap it. Same with the oil filter remove the small screw to avoid a huge mess, besides this a good clear video, keep it up. Look forward to seeing more!

The paint is to thick needs a little water

Seems good 👍can you tell me if this would be the same to do on 2015 insignia 2.0 cdti ecoflex sports tourer ?

Hello, can a better camera like yours be installed instead of the original one. I have a bad picture, it's blurry... can I also connect it or do I need some more modifications? I have a 2014 Opel Insignia Sports Tourer

🔥 P r o m o S M

Hi great vid, I was just wondering, I have a non sat nav in my 2014 insignia but would like to upgrade it to the factory sat nav touch screen one, would it be a straight swap or not? Thanks

Where u based can u do mine

How did you fit the camera cable through the boot from the outside into the inside where the rubber grommet is? You cut the footage there 1:37

Inguardabile...

Do you have a link to the injectors and to the copper washers thank you