5 жыл бұрын
Пікірлер
@JonnyPee1691 3 жыл бұрын
My dad was struggling and now he knows he need to force it a little bit more
@mikenorman1837 5 жыл бұрын
The man I'm trying to do that and it is not that easy like it is stuck
@bmwcheapfix1342 5 жыл бұрын
Sorry for the delayed response, I hope you got them loose. Sometimes they can be stubborn. (old O-rings probably stiff) If they are really tight, then remove the fuel rail by removing each injector clip and take each injector out individually. Careful not to drop a clip!
@jamaalbey6306 5 жыл бұрын
I sent over my discovery to the email
@jamaalbey6306 5 жыл бұрын
Can this seal cause a misfire on cylinder 6 by any chance I have a 325xi and having all kinds of issues. I have replace everything on the car.
@bmwcheapfix1342 5 жыл бұрын
If the rear main seal were faulty it would cause more issues than just cylinder 6. I would focus on cylinder 6 specifically. Check the coil ground cable first then maybe swap coil with another cylinder to test if the coil is bad. Check the plug as well. You could also check compression in that cylinder. Keep at it and you'll figure it out eventually. Keep us posted!
@jamaalbey6306 5 жыл бұрын
I have done everything you mentioned. Ccv, swapped coils swapped injectors, changed plugs, coil boots, intake gasket, valve cover gasket throttle body oring, checked all wiring harnesses ignition and fuel injection and Maf, sealed disa valve checked rubber boot replaced all vacuum lines O2 sensors all 4. So I'm stumped
@bmwcheapfix1342 5 жыл бұрын
Have you checked compression in cylinder 6? Also, are the coils new or original equipment? BTW, what year is your 325xi?
@jamaalbey6306 5 жыл бұрын
Do you have a email I can show you what I found on the DME
@bmwcheapfix1342 5 жыл бұрын
Sure send me an email at [email protected]
@omarduronchavira1525 5 жыл бұрын
Help me my car pulls gasoline by inyectores but only in the mornings when its cold after all normal. Do you have any solution please. Already change leagues
@bmwcheapfix1342 5 жыл бұрын
Visibly leaking gas is probably faulty o-rings. Addressing the rubber o-rings first would be a good/cheap way to start. Leaking injectors (internally) would need to be cleaned/refurbished, or simply replace with new OEM injectors.
@jamaalbey6306 5 жыл бұрын
Since the weather is getting warmer I can focus on changing the diff fluids. I own e46 and e90 both all wheel drive.
@jamaalbey6306 5 жыл бұрын
Great videos I have a 02 325xi I just did a lot to and your videos have helped. Thank you keep up the great work
@bmwcheapfix1342 5 жыл бұрын
Your very welcome. Glad to help!
@clubherbalife6292 5 жыл бұрын
Lol I do too ! But it's easy
@peterboldt3131 5 жыл бұрын
Hey buddy nice video I really appreciated seeing your body and head
@bmwcheapfix1342 5 жыл бұрын
Thanks. I think we can all agree on more head!
@trinidadbreeze 5 жыл бұрын
those wire for oxygen sensors not converter
@bmwcheapfix1342 5 жыл бұрын
Thanks, it was probably what I meant to say.
@alexmeroy6688 5 жыл бұрын
what are the bolts and nuts size? thanks.
@bmwcheapfix1342 5 жыл бұрын
They were just some stainless bolts I had in the drawer. Sorry I can't recall the exact size. (maybe 1/2" SAE)
@georgebasha8043 6 жыл бұрын
remove the clips first
@mikesavage8379 6 жыл бұрын
So Does it run? How has it been since rebuild?
@bmwcheapfix1342 6 жыл бұрын
Yes sir it is running. lol. I have several more videos to post. Hope to get to them soon.
@felonyurbex633 6 жыл бұрын
so does it run?? lol
@bmwcheapfix1342 6 жыл бұрын
Yes sir it is running. lol. I have several more videos to post. Hope to get to them soon.
@felonyurbex633 6 жыл бұрын
is this video out of order?
@bmwcheapfix1342 6 жыл бұрын
Well, I did the work as I could, when parts would come in. Initially I was going to rebuild the top end, but as I got into it, I decided to pull the engine out. So some things are what I could do, when I could do it.
@sieve417 6 жыл бұрын
Started from part 1.