21 күн бұрын
5 ай бұрын
6 ай бұрын
Жыл бұрын
Пікірлер
@danamarfoglio9016 16 сағат бұрын
Thank you- gives us the confidence to put up our own
@sengsational 6 сағат бұрын
I remember how I felt when I saw ALL those parts! I didn't think I could do it.
@carolinem.9800 7 күн бұрын
4500e. the emergency pull cord broke off right at the trolley, leaving maybe 1/4 inch hanging out. called marantec-- they recommended crosby, a local installer. the local installer told me: 1/ I needed a new trolley ($110) and 2/ a new rail 'because I will have to take the rail off at the door header to replace the trolley. ..and the rail bends and is damaged '. . " COSTS: new rail = $400 , then plus labor to detach old rail and operator (motor), take off old trolley , put new trolley on new rail, reassemble new rail to operator, reattach operator to ceiling, then reinstall rail to door header: , I'm looking at $1000 to replace a DEFECTIVE POORLY DESIGNED WEAK piece of cord! Thank heavens for this you tube video! took out old cord, put in piece of wire, attached new cord.
@sengsational 6 сағат бұрын
If you could have seen the Crosby guy while you described your problem...I think you would have seen a "$" in each eye :) Excellent work getting out of it with your wallet intact.
@jkimo1178 11 күн бұрын
To fine tune the fit I CAREFULLY used my bench grinder.
@sengsational 6 сағат бұрын
Yeah, you don't want to grind away the electronic "goodie" in the plastic case!
@jkimo1178 5 сағат бұрын
@@sengsational I was very careful... just used it to make things square and grind down sharp edges, etc.
@liangQ1 13 күн бұрын
Thanks. Legend
@sengsational 11 күн бұрын
Glad you liked it.
@aviira 16 күн бұрын
Awful
@sengsational 11 күн бұрын
Sorry to have consumed your time with something you didn't like. I hope you find something else to enjoy.
@johnmacmillan627 19 күн бұрын
It worked like a hot damn ! I followed your instructions to the T. Many thx again
@sengsational 17 күн бұрын
Glad you found it helpful!
@tmon4819 20 күн бұрын
Do you have installation video of the fans?
@sengsational 19 күн бұрын
Sorry, I didn't do one for the fans. But I did take some pictures for how to hang the fans: diy.stackexchange.com/questions/229565/how-to-hang-a-ceiling-fan-in-a-metal-gazebo
@tmon4819 18 күн бұрын
@@sengsational ok thanks
@johnmacmillan627 21 күн бұрын
Very helpful! Didnt know this existed until I couldnt start my car after changing fobs
@sengsational 19 күн бұрын
Glad you found it helpful. I only "kind of" knew there were there, depending on the car. It was pretty obvious there was a problem when my car wouldn't start without it!
@lindaKessinger 22 күн бұрын
It's just the video I am looking for. Thanks for making it so I could follow you.
@sengsational 19 күн бұрын
I like to do videos where I'm a learner too. The pro's might think I'm a blockhead, but regular people can sometimes identify.
@e.lan.s 23 күн бұрын
are you using Zenfone9/10? 😂 Seems to be the same i have
@sengsational 19 күн бұрын
I looked that up. I think it's a phone sold down under? No, my phone is a Motorola G Power 2021.
@rufinod470 Ай бұрын
Have a Marantec Viper X70 model and have the same issue. For years, it needs to be replaced but couldn't till now, after seeing this video, It was tricky and delicate fix but it worked. The original hanging string/rope seems to be sturdy except the part inside the unit which to me is very suspicious. It's bound to happen sooner or later. Surely saved some money from your video. Thanks.
@sengsational 27 күн бұрын
Glad you were able to get it solved without spending lots of money!
@leosmith8661 Ай бұрын
God bless you!!! I was about to give up (which I never do) and made all kinds of homemade tools, looked at KZbin’s until I was blue in the face, but wasn’t sure what brand faucet it was. And then … I decided to use the Google Lens and it instantly told me what brand and model 😁 Then I found your video. You Da Man!!! I’m going to do it tonight after work. I also ordered a WiFi valve to turn off the water. My wife doesn’t do anything fast so it’s just easier this way … LOL. Thanks again!!!
@sengsational 27 күн бұрын
Ah, very smart to use Google Lens! I only use it for plants, but I need to think outside the box. Anyway, glad it got you to a solution.
@junjun5820 Ай бұрын
i just build up a new 12x16 hardtop gazebo like yours. and i facing the situation middle of the beam is leaking , same as ur video. and it's brand new, no blockage. how can i fix it? tks
@sengsational 27 күн бұрын
Hard to say why it's leaking. My guess would be that the roof panels are somehow not in the right position.
@junjun5820 26 күн бұрын
thank you for you answer and help. i have the same situation as 0:43-0:44 as ur video. I put silicon on the gap from top. but not help at all. any more sugeestion can help on that? appreciate.
@sengsational 25 күн бұрын
@@junjun5820 I misunderstood your earlier question. Leaks from the horizontal beam joints are likely caused by water getting in at the corners and running along the beams. Doing the things I did in the video (plugging up the beams on the corners and cutting the plastic corner pieces) is all I did, and that solved the problem. Have you done those things?
@ChiRat22 Ай бұрын
This is the exact video I was looking for. I will give it a shot tomorrow.
@sengsational Ай бұрын
I hope your project was a success!
@ChiRat22 Ай бұрын
@@sengsational ordered everything including the plastic pieces but haven’t tried it yet.
@lcassidy3607 Ай бұрын
Hi! May I ask how you mounted the fans into the aluminum gazebo? My husband is saying that you're not supposed to drill into the aluminum as it would shred? Thanks in advance! :)
@sengsational Ай бұрын
I had the same concern about hanging the fans. The solution I went with is here: diy.stackexchange.com/a/232680/4323
@lcassidy3607 Ай бұрын
@@sengsational Thank you very much for the info. I would have him look into it. He's also concerned because it rains pretty heavily in our area every year. He thinks the weight of the fan is too heavy. :D Hope yours is still holding up. All the best to you & your channel. :)
@sengsational Ай бұрын
@@lcassidy3607 The structure seems very solid to me; I never worried about the capacity to bear the weight of the fans. I'm not sure what rain has to do with it, unless there's a concern that water will blow in sideways and get on the fans. So far, these fans are continuing to work just fine.
@lcassidy3607 Ай бұрын
@@sengsationalYou're right, it was kind of a stupid question since it's a covered area. Sorry about that hehehe! Thank you for your reply. :)
@MrZeaos 2 ай бұрын
i would add teflon tape to the threaded fitting for the toilet supply line and also would have caulked at least the sides and front of the toilet
@sengsational Ай бұрын
Thanks for your ideas. Either or both are fine. Teflon tape is a distinct requirement for fittings that seal on the threads (tapered), and can be helpful in the case of the toilet supply line, where the seal is on a gasket. If you feel like tightening can be smoother with the tape, there's no harm in using it. Caulking the toilet to the floor is fine, but if the seal between the toilet and the waste pipe fails, I'd rather see the leak sooner, and get the problem addressed, as there is no amount of lthat type of liquid that's allowable on the floor.
@chopsueycop 2 ай бұрын
my knob completely fell out, and your reconstruction part at the end of this video helped me put it back together. thanks!
@sengsational Ай бұрын
Glad that part of the video was helpful. I knew as I'm trying to figure a way to do something, I might have viewers saying "all ya need to do is....", while I'm fumbling around, LOL! But I like to show my head-scratching and strikes and balls as well as the hits.
@charliewilson3234 2 ай бұрын
Great experiment, thanks.
@sengsational Ай бұрын
Glad you liked it! I don't remember where I learned how to make the spinner... probably a 30 year old memory from when the kids were little.
@andyhawkins880 2 ай бұрын
The chip is in the remote module and this isn’t required on all Honda fobs.
@hadesmcfadden2982 2 ай бұрын
not always. I just encountered this moving the remote module from my '06 pilot to a new shell and it would not start without the old transponder moved over.
@sengsational Ай бұрын
If that was the case with my car, I would not have done it. I got the new key set up without moving the chip and it wouldn't start. But no harm in trying the new key without moving it...the worst that can happen is you realize that the car in question needs it moved.
@Jolie-cf2ei 2 ай бұрын
About 9020T continued... This machine has the electrical connection on one side and the motor below in a separate compartment. Do I disconnect only the outlet on the machine before trying to remove the 2 hook gears?
@sengsational 2 ай бұрын
In general, I like to first take photos before disconnecting things. As I recall, the long shaft could not be removed until some electrical things were removed. Although the timing is good now, when the gears are replaced, the timing will probably be disrupted. You might be able to mark the shafts before disassembly, but I have no experience with that. Since the timing is good now, I would take a close look at the way it works now, and take pictures, so you will recognize good timing after you replace the worn gears.
@Jolie-cf2ei 2 ай бұрын
My machine seems to be newer than the ones usually fixed. It's a 9020T Singer. Only problem is worn hook gears. Timing is good.
@sengsational 2 ай бұрын
I responded to the other comment, but I'll add that you might come back and let us know how the repair worked, and which components had to be removed on the 9020T repair.
@cgtotty 2 ай бұрын
Thank You !! I'm shopping for an ice machine for a church and trying to figure out what bin storage capacity might be best. Never thought it would be SO DIFFICULT to find applicable results on Google. You can easily find just about any facts on ice except for "how many bags of ice to fill a 48 qt cooler". Thankfully I found your video in about 10 minutes or so.
@bored2dad 2 ай бұрын
Brilliant result! Thanks for sharing. Just bought a new Orion cooker and going to try out this method. Charcoal is costly and if not careful, it might end up about the same price as eating in restaurant. Since the charcoal I'm using is hexagon shaped sawdust, it can be stacked in four places, hence I wouldn't need partition for now. Does the 3 hours apply to whole chicken as well?
@sengsational 2 ай бұрын
I haven't been doing the charcoal saving method because I moved on to an even less expensive way to heat the Orion: propane. A bit more work, but I've had this running successfully for years: kzbin.info/www/bejne/rZDZfKurqN6tpLM There's also an even easier way to convert your Orion to propane, and that's by using the burner out of a "Big Easy": kzbin.info/www/bejne/pniTmKudh66Dn6s Note that you can very often find these used Char Broil Big Easy cookers on craigslist for cheap (because people leave them outside and they rust). But the burner is still fine, and that's all you need.
@JSERVFINANCE 2 ай бұрын
Hi. I bought the same fan it looks like i my gazebo with a 2 ft downrod. do you have any wobble with your fan? i have a slight wobble. wondering if thats normal
@sengsational 2 ай бұрын
My fans are pretty stable. Fans often wobble when the fan blades are not equal in weight, or the fan blades are not all in the same plane. I would first get a fan balancing kit and follow those instructions, which detail how to place a test weight on different blades. If you find smoother operation, you add a permanent stick-on weight. Before you get the kit, you might just swap pairs of blades, swapping the position of two blades opposite of each other. Good luck in smoothing things out!
@delauren667 2 ай бұрын
I have the same lawnmower as you. Can you provide a link where you purchase the carburetor? TIA.
@sengsational 2 ай бұрын
These links change all the time, but here's one www.ebay.com/itm/403689073823 For future readers, search "CARBURETOR Fit For Tecumseh 640350 640303 640271 Sears Craftsman Mower Carb Kit" or some variation of those words.
@josephgil3843 2 ай бұрын
Great test - thanks for sharing the findings and how to did the test. Very pleasant to watch.
@sengsational 2 ай бұрын
Thanks for the kind words. I'm always exploring density. It's under appreciated. My ice density video had the same origins: I wanted to know, couldn't find an answer, so did an experiment ( kzbin.info/www/bejne/eICpppyGja5rjrs )
@bigandfatty1 2 ай бұрын
It’s spinning backwards
@sengsational 2 ай бұрын
That's what I thought when it didn't generate the expected breeze. And despite what it might look like, I know which side of the blade was the leading edge, and that edge was higher, so blowing down. Scraping from the ceiling side and pushing to the floor side. But in these days of fake stuff for shock value, you're right to be skeptical. I'm not that guy, though. But you have no idea if I am that guy, hehehe! Lookup "cavitation", I think that's what we have here with the short downrod.
@pearl427 2 ай бұрын
Thanks much for showing the hole to use. I was way off. Save me from buying a new Mower! Thanks again!
@sengsational 2 ай бұрын
Yeah, I remember thinking "oh no, which hole??" I try to remember to take pictures before I start any disassembly process, but don't always remember.
@johnvwgmail7233 3 ай бұрын
Thank you, very helpful. Especially the things that didnt go right initially, thats how it goes
@sengsational 2 ай бұрын
Yeah, I try to include the blunders...maybe save you from suffering through the same ones I did. Besides, when editing videos, as in life, if you simply include everything, even things you're not proud of, then there's no discontinuities that need explaining or covering-up.
@itsmejas0n 3 ай бұрын
I had two problems. The one mentioned in this video and the other where the microwave would not heat nor spin. I checked, and two of the switches are broken. One did not allow any current to pass through without clicking the switch, and one kept the current going unless clicked.
@sengsational 3 ай бұрын
Right, these switches are usually of the type "NO" (normally open) or "NC" (normally closed). Depending on how they designed the circuits, they put those different types of switches in. I never know what I'm going to encounter, so I just put an ohm meter on the switch and make sure it changes when clicked. But one of the problems with these cheap switches is sometimes you can get it to work when you manually click, but when the switch gets pressed by the door, it doesn't work. Intermittent stuff like that can drive you bonkers!
@berad3574 3 ай бұрын
The title made me think you were going to install it with one hand just to show off. 😂
@sengsational 3 ай бұрын
Ha! Yeah, I got my first sail boat when I was 7 years old and so "single handed" is when you operate the boat by yourself. Sixty years later, and I just now tried sailing something where I needed another "deck hand" to manage the boat.
@AngelKsiezyc 3 ай бұрын
Where they the same price? Could you provide the link for the real ones?
@sengsational 2 ай бұрын
Things change a lot with technology, so I'm not sure the TUNE 230NC are the current model any more. I searched Amazon for "jbl noise canceling earbuds wireless" and it came up with www.amazon.com/JBL-Tune-Flex-Wireless-Cancelling/dp/B0C1QNRGHC for $70 (model JBLTFLEXBLKAM). If you see some JBL's with ANC (active noise cancelling) for less than $60, I would make sure you were ordering on a site where you could do hassle-free returns.
@AdriannaWhittin 3 ай бұрын
It is a scam, 13.50 for inspection isn't enough for overhead expenses, therefore some dishonest inspection garages do dirty tricks and deceptive tactics to get the customers to buy their wipers blades, it's about money. Terrible❗The day I had my car inspected, the same story, It will not pass because my blades were bad,” I knew how my blades look before going in. I said ok but the next customer the same story, your car will not pass due to bad blades. Then I thoughts to myself, everybody blades can't be bad. Now, I am doing research. What the NC states considered bad blades I found, my blades were not cracked/torn nor jagged edges. I will be prepared the time, I will take pictures and provides this print out information as my evident, enough or scamming. The public needs to be aware of this, “another scam”❗
@sengsational 2 ай бұрын
I would expect in these days of Yelp and Google reviews, businesses would be concerned about getting bad reviews. But if you look at reviews for some places, the only reviews are negative...people are only motivated to review if they get the shaft.
@terryf5131 3 ай бұрын
How is it holding up? Wind..snow..etc..thanks!👍
@sengsational 3 ай бұрын
We don't get snow here, but we've had wind, and it's been solid. I've got lag bolts into framing members on all 6 feet. The wind seems not to have any effect, at least up to 40mph gusts, which we've had a few times.
@terryf5131 3 ай бұрын
@@sengsational ok..great!! Thanks for the input. 👍
@jkucukov 3 ай бұрын
Thanks for the detailed video, I have the same exact tub/faucet setup on my 1999 home. I dont have a certificate with fancy gold stamp detailing the Lifetime warranty. What proof did Moen require in order to get their cartridges shipped out to you?
@sengsational 3 ай бұрын
I just emailed or used the web contact button...not sure which. They're pretty lenient, I think, for providing proof. You might just be able to request replacements without any certificate or anything.
@jkucukov 3 ай бұрын
@@sengsational Thank you sir, you saved me some money and time. I emailed Moen and I should have two replacement cartridges in a week.
@evelyngilbert6715 3 ай бұрын
Thank you for this video. I got some authentic as a gift a year ago, and I LOVE THEM. I want to buy a a gift for my son, now I know what to look for.
@sengsational 3 ай бұрын
I originally learned about them from a flying buddy of mine. He's usually pretty low energy, but when he talked about the JBL's he was enthusiastic. That's all I needed to go for the JBL. When I got the fakes, it simply would NOT do!
@Keepingittocool 3 ай бұрын
Wow old video but very helpful I’m working on one and the float is gone and didn’t want to do a rebuild. Thanks
@sengsational 3 ай бұрын
Yeah, The carbs are so cheap that rebuilding a carb doesn't make a lot of sense. I don't have that mower any more. I think after some number of seasons in the cold/damp, the cylinder wall and/or piston and/or rings corroded because it seemed like it had less compression (I didn't have the tool to test). The wife, without my consent or knowledge bought a new mower (LOL!). This mower ended up on the curb and a neighbor took it away.
@rezashir7964 3 ай бұрын
Thanks
@sengsational 3 ай бұрын
Glad to help.
@karenmckamey8287 4 ай бұрын
Thank you!!!!! I watched so many videos and this is exactly what I was looking for!
@sengsational 4 ай бұрын
Glad it hit the mark for you. I've done a few more cabinets the same way and they have separate videos. When I searched, there were a lot of videos making a big deal about the wood working, but I went simple there, but still effective.
@richardcamp7382 4 ай бұрын
Excellent advice! Using a long deck screw to remove the stuck cartridge worked like a champ. Just made sure the lifting force from the claw hammer kept the screw perfectly vertical throughout the lift. I can’t thank you enough. Spent hours watching youtube videos of various tools that were incompatible with the Moen 1248 cartridge and had about given up. Your solution was the best of any. Awesome!
@sengsational 4 ай бұрын
Glad it worked for you. That screw idea and keeping it vertical, that was a good observation.
@JeffreyTobey 4 ай бұрын
Garage door opener is about 6yrs. old. Your correct that the rope is junk! Went to release the opener and it obviously broke. Watched your video and about 10 minutes later new rope was installed and works like new!!! THANKS!!!!
@sengsational 4 ай бұрын
You nailed it in 10 minutes. That's great!
@VillaLumina 4 ай бұрын
Love it. ❤❤ I strapped my indoor tv onto my purple leaf gazebo without drilling using the ZeboZAP. Love the setup with tv outdoors 🎉🎉🎉🎉
@sengsational 4 ай бұрын
My brother in law bought the high-dollar outdoor TV. I didn't put up a TV in mine.
@jf8322 4 ай бұрын
We’re can u order just those plates and bolt kit
@sengsational 4 ай бұрын
Sorry, Can't help you there. Everything you saw was in that one kit that I bought.
@rickc564 4 ай бұрын
Never ever get rid of your older direct drive washer! These new washers with the locking lids and all the pretty little lights SUCK they are throwaways these days
@sengsational 4 ай бұрын
Thanks for the suggestion. Every time my wife makes noises about getting another washer, I remind her of all the complaining I hear about the new fangled throwaways.
@doctornevermore4315 4 ай бұрын
Do you know if the fakes are still waterproof?
@sengsational 4 ай бұрын
Hmm. I sent mine back, so never got a chance to test that.
@rahulshah1408 4 ай бұрын
E442 I have a bad feeling.
@sengsational 4 ай бұрын
I've got a "worse" cabin booked on a fancier cruise line. There's only about 12 cabins on the whole ship that have obstructed view, but I'm looking directly into the lifeboat, not over it (on the Azamara Journey). At least I can tell if it's day or night :)
@rahulshah1408 4 ай бұрын
@@sengsational that’s my worst case scenario. If I can get sea air and drink some oj. I’m happy.
@kenashcom7580 4 ай бұрын
Great video, it will give me the confidence to do the job, but I don't know why you didn't release the muffler. It's easy to do.
@sengsational 4 ай бұрын
I tried to release it, but couldn't get those rubber things off. They made it look easy on one video I watched, but I couldn't get the right angle to pull.
@user-bz4uz8jj2t 5 ай бұрын
Very helpful - thank you!!
@sengsational 4 ай бұрын
I'm glad it was of use to you.
@HotRodReverend 5 ай бұрын
Subscribe earned - thank you for showing the testing leads, etc. My thermal fuse tested fine with continuity on the Ohmeter. The hot lead showed 120 volts but the other terminal was dead in the water.
@sengsational 4 ай бұрын
I'm not sure I'm good for a repeat performance, LOL! I run into a problem at my house, look for a video, and if "a good one" isn't forthcoming, I make one. And yes, try to include all my steps, including mistakes.
@markarness8719 5 ай бұрын
Yeah I got one just like it tysm for posting, unraveled the mystery for me! parts were clean and serviceable, just needed new O-ring. Valves lifted out easily with gentle pressure on the stem extensions, slipped plier under the top nut and gently levered, popped right up. My escutcheons so frozen to pipe after 24 years they won't come off, I saw another post where some desperado sawed em off with a dremel cutter, lol. Nice post for what looks like an easy job but isn't, tyvm!
@sengsational 4 ай бұрын
Oh, what a drag that it wasn't an easy one for you.