Love it

I hope you’re in Florida because I want you to come to my home 😊

Nice.... Protects the mice from the cats, by keeping them out. Oh and not to mention snakes. Good job.

How do you take them off with destroying the walls?

This now 125 dollars

Won’t the spacing in between allow for critter like mice get in?

Good video BJ

Hello, roughly how much would you charge to install an exterior door like that in that FL area? (not including door, Labor only)

With these panel surrounds, what is normally done if there's any work needed in the shower valve fixture? Will these basically need to be all ripped out and redone after the work is completed? Are there any options where maintenance and plumbing work can be done after the panels are installed? If there were a service access panel incorporated into these surround panels it would be easier to deal with future work, but it appears they're always designed as a single piece to be installed after all the plumbing is completed.

Thumbs up for this video!! The detail and responses on your page are insanely helpful! Thank you.

Good Content here. Covering the basics well but not going into needless detail. Thanks

Concrete not cement

Quick question… I purchased a proFlo shower base that does not have walls made for it. There is just a plastic lip. Can I use this with it? I was told I had to use tile, but it’s too expensive.

Where can I find this shower wall

I hope no one follows this advice. About half of this video is wrong. Search on other roof coating videos from pros who do this for a living as there are hundreds of of them on youtube.

I prefer to brush blast with a sandblast pot and black beauty if theres a lot of rust , if theres only some rusty spots you need to wire brush and sandpaper them VERY GOOD try your best to get to shiny metal underneath. ( even tho you wont completely) prep is 80% of the job ,dont rush it. a drill with wire brush wheel works good too. then dust off or blow off all the rust dust and power wash with soapy water , if there are brand new areas of sheet metal wipe them off with MEK and a rag to remove any factory oil film before power washing. replace any screws or put in more where you see the metal flexing using screws with rubber gaskets attached under the head you can buy them by the bag. then spray on a coat of iron oxide oil based primer , after its dry completely ,spray it with hi gloss white oil enamel and then hit it with a second coat when the first is completely dry. after 8 years power wash it good ,let it dry and spray one more good coat of white hi gloss oil enamel to get 15 more years out of it. edit-(40 years local 8 steel painters and allied trades,retired)

Grwt build. Loxking to redseign mine. Did you use pressure treated wood? Did you seal the wood? Also, how long were your carriage bolts? Why did you add the metal plate for the locking toggle clamps?

thats awesome u help me a lot with this video and very well explaining everything by details

Crazy shit! Please don’t do this! Your cheapness will haunt you later when it will cost you even more to fix and what little you spent will also be a waste. Remember, you get what you pay for: cheap shit!

I had never done this before. This video alone gave me the confidence to try it and I had no issues!

Went up to $130 now 😬 Can we use this for tile around the bathroom or do you recommend something else?

Have you ever tried to install a shower wall over a wood shower wall made out of 2 x 4s. We had a tenant that decided that was a good remodel idea so he built all 3 walls out of 2 x 4s and, of course, he nailed them in. This is proving to be a real nightmare.

you can put this onto regular dry wall without any waterproofing?

So for the price of extra material and your time buy some decent shit. Thanx

Where did you find the trim for the surround ? I have a similar tub but no trim

Exactly the info I needed! Many thanks!

listen.....this will work

It looks great. Does the heat from the pool heater vent ok without damaging the PVC?

Very nice, it's also better when it's against house wall but mine is free standing next to pool under a tree by neighbor's fence about 10ft from their fence. How do you detect the pool water pipe so you don't damage them during digging?

Hi Liam, can I ask how much that set up is worth with the side rails on it. The reason I ask is we inherited one from my father-in-law I don't think it's ever been used but we found the side rails and we're gonna put them on today and try to figure out what is a reasonable sell price to try to sell it for

dein sheetrock can get soft tho might push a hole thru the whole thing?

Can this be applied over tile and if so what adhesive should be used?

your project looks gorgeous. I am trying to have get done the same type of project but could not find anyone ?any tips to finding someone.

😮😢use gloves

Creative and looks great! But it must get very loud when it rains!!! And come off during strong winds/hurricanes?

I watched this video just to see how to deal with the window. My homes builder put a nearly full size window in the shower. Plus the window sill is tilted inwards and catches water. 😅

what is the model of you spray air less Graco? have you tried roof coating elastomeric with the spray paint machine?

Great video just what I needed

Great. What kind of Greco sprayer

Your laugh is priceless!

Wow, I wish everyone was as precise as you. Fantastic!

You used an Acrylic Kilz2 water based primer, under enamel? I don't think so.

Where did you get the shower wall material? And what is the name of it.

How did you attach the skirt to the siding of the house?

That roof needed torn out! I guarantee you, there is wood rot throughout that entire roof!

I have no idea want to do i keep try not is work how mush $ for you to do it for me

I need help fit

Thanks Ali! I have the Northern tool foldable aluminum trailer and learned a lot from your video. Well done!

Great idea! I am looking into skirting for my tiny home.

It’s cool to see you use all the different tools. And make things look better ( pretty ) Wish I had a man with your skills.