Zgrtaci za travu moraju se skinuti da ne nakupljaju travu
@klausolk33735 ай бұрын
Ja, was die Ingenieure sich wohl bei dieser Sauerei gedacht haben. Pfusch schon ab Werk. Keine Verzinkung, keine Versiegelung mit Hohlraumwachs. Und sowas ist Made in Germany. Schämt euch.
@josueangeles40888 ай бұрын
.__.
@thebeeamberheardsdogsteppe63688 ай бұрын
Thats the most dumbest thing o have seen
@carlosrivaswerner86208 ай бұрын
😐
@wonka684811 ай бұрын
Tolle Maschine. Ich habe die auch. Hast du Ahnung bzgl. schmieren und pflegen der Maschine? Ich komme beruflich aus einem ganz anderen Bereich und kenne mich diesbzgl. leider gar nicht aus.
@dompert11 ай бұрын
Guten Abend, ja das stimmt die Maschine ist wirklich klasse. Allzu viel mache ich wartungstechnisch allerdings gar nicht, sie kommt bei mir auch nur noch sehr selten zum Einsatz, da ich in meiner Hauptwerkstatt noch eine andere Bohrmaschine stehen habe. Auf die Säule mache ich hin und wieder etwas Gleitöl, in das Getriebe für die Tischverstellung etwas Fett (da sind oben zwei Druckknöpfe) und vorne an der Pinole ist auch noch ein Druckknopf, da drücke ich auch etwas Fett rein. Habe aber leider auch kein originale Betriebsanleitung mehr, wo beschrieben wäre, was man genau nehmen sollte.
@ThePolog60 Жыл бұрын
Hi gibt's den noch teile für solch eine ... Mir fehlen noch paar Dinge ..
@dompert Жыл бұрын
Hey, würde sagen wird eher schwierig da auf die Schnelle was bei zu bekommen, hin und wieder sind Ersatzteile von der Maschine auf Ebay eingestellt, da muss man dann aber Glück haben und zum richtigen Zeitpunkt suchen...
@jxg1652 Жыл бұрын
A little bit too fast perhaps.
@dompert Жыл бұрын
Yeah, probably you are right, maybe I will try another attepmt with slower speed.
@feracingdf292 жыл бұрын
Nice. I have a bst 13. I struggle to remove the Chuck. Is it screwed on or Jacobs taper? Thanks!
@dompert2 жыл бұрын
Thanks. It's a jacobs taper. Over the chuck is a nut with a wrench flat. You have to turn it down, so that it touched the chuck. Now you have to hold the chuck in position and turn the nut just a little bit more down and the connection is opened.
@feracingdf292 жыл бұрын
Thank you so much. Which way do I turn the wrench when standing in front of the drill press? To the left or to the right? The nut is really stuck….Thanks again.
@dompert2 жыл бұрын
@@feracingdf29 it's a right-hand thread, so you have to turn to the left to open the nut, if you stand in front of the drill.
@feracingdf292 жыл бұрын
It worked! I got the chuck off. Thank you so much. Now, it appears I have a little runout on the spindle. Not sure what to do with that. Whether it is bearing slack or bent spindle…
@dompert2 жыл бұрын
You´re welcome. And good luck with your spindle.
@tokreez85672 жыл бұрын
Yoo 1 SVM MTK sekalian
@r.d.g.s.p97622 жыл бұрын
Noooooo
@vaseemshaik13833 жыл бұрын
Dresser name
@dompert3 жыл бұрын
Hello, actually I don't have the name of the dresser. It's an elder one that I found ones on a flea markt, no company name is shown.
@wcfields547 Жыл бұрын
YOU SHOULD NEVER EVER WEAR ANY TYPE OF GLOVES WHEN USING A BENCH GRINDER SO DANGEROUS ⚠️
@adibadibadiadi4243 жыл бұрын
так себе игрушка ...геморойно..
@dionisiedradici64903 жыл бұрын
Acolo nui tăiată bine
@carolinmartinez23103 жыл бұрын
República Dominicana
@carolinmartinez23103 жыл бұрын
Yo vivo en r d como puedo comprar una máquina de ésa
@carolinmartinez23103 жыл бұрын
Quiero saber si puedo comprar una
@dompert3 жыл бұрын
Hola, espero que el traductor de Google produzca algo útil ;) Es un Agria 5300 de un año de construcción anterior. Puedes comprar la última versión aquí: www.agria.de/en-gb/products/Balkenmaeher/agria-5300/index.html (unpaid advertising)
@carolinmartinez23103 жыл бұрын
@@dompert ok
@johnewadonis39524 жыл бұрын
Sorry but your method of removing rust is not very good if you use a rest remover liquid or by vinger or the electric way it will be more better
@Mario1804795 жыл бұрын
Servus, Du hast Dir auch die "Heidenau 4.00 - 8 AS Reifen" gekauft :) .. Die habe ich mir auch drauf gemacht. Was mir persönlich (positiv & negativ) aufgefallen ist, daß das 'Profil' der Reifen sehr gut 👍 & v.d. 'Gummi-Mischung' her TOP ist 👍 aber der Reifen keine 4.00 - 8 hat, sondern 3.50 - 8 👎eigentlich die Bezeichnung haben müsste ➡ Dieser ist sehr schlank gehalten gegenüber den (originalen) alten Reifen... ...lg. MARIO.
@TheSitg5 жыл бұрын
well done!
@dompert5 жыл бұрын
Thank you ;)
@dompert5 жыл бұрын
What do you think about the first part? Any reactions are welcome!
@marc1al906 жыл бұрын
Where is part 2?
@dompert6 жыл бұрын
Hello Nicolas Adalid Marcial, actually I am trying to finish part 2 within the next week, so keep watching ; )
@marc1al906 жыл бұрын
Dom Pert commentary would be great as well as info about you getting ahold of the grinder. Inherited or a yard sale find? Thanks and looking forward to your next video. Got the reminder turned on.
@dompert5 жыл бұрын
Hello Nicolas, sry for the late reply ;). Finally I have uploaded the second part of the restoration with the final result. The grinder has been an old fabric find. So glad I've heart about it.
@Reiner096 жыл бұрын
Wie hoch sind die Räder am Mähbalken vorne?
@dompert6 жыл бұрын
Hallo Reiner09, bei mir haben die Räder vorne einen Durchmesser von 200 mm. Auf der Felge steht 180 / 200 /225 x 50 .
@Reiner096 жыл бұрын
Dom Pert Danke für die Daten möcht mir auch solche selber bauen