We got a 2011 Cube their all similar. The belt tensioner pulley bolt was a PIA. We had to drillout with a step drill bit on the wheelwell side panel. Thanks for the video it doesn't look as bad as doing the belt tensioner pulleys.

Where did you purchased those struts ? Were they difficult to install? Awesome job installing alternator.

Electrical gremlins on these cars. My son had an 08 base model. I miss it

Very helpful thank you

Finally a video that shows the whole process.

Do you have a video of changing the hoses please behind the power steering pump ? I got quoted 350 from a store to change them but they cost $30 from a wreckers and i rather do myself. Thanks

That was a bad brake job probably dangerous. Great heads-up on the front facing rear control arm.

Appreciate the heads-up real video. One little ha k I try is to break the hard to get to get to bolts first on a ramp at least soak in WD-40. TOUGH environment for vehicles. Looks like a solid design.

What else could I use for a constant power, I don’t wanna risk losing the display, Bluetooth, audio system etc

Gosh, I was considering a Kizashi, but the CVT is such a turnoff. 😒😒 Such ashamed on a nice car.

Nice and simple, thanks for the video

Thanks a lot, I’m going to give it a shot after this vid

only thing i would say is hearing you talk is so much better but i understand u wanna listen to music while u work understandable… the screw part i wish we could have saw u put the rubber on the screws. also my kit came with alot of rubber screw pcs where do all them go i only seen u replace the 4 spark plug/ignition coils screw rubbers also put on the parts back but ya cam freeze but thnx for the video remember if u gonna do something make sure u do it right even if u have to go back and fix it

best video out

Saved my ass. Thanks!

What a pain in the backside. I'm getting ready to go do that to my wife's car right now. Thanks for the video.

Recommend different type of globes tbh my guy I prefer the doctor globes lol

Gosh darn haha. My gf alternator went. So I changed that, which was an absolute nightmare obviously lol. I'm a body tech so I was able to evac the a/c and just move everything out of the way and change it. Now her thermostat is gone. Looks like I have to go back in and rip the alternator out as well as the a/c and compressor just to get to that. Holy, what a nightmare

Historic

Great video. This convinced me to pay a local shop to fix my bad bearing in my Elantra! Quoted $450. Price I pay for not wanting to do it myself!

Good video thank you

Whats the ac Delco kit part number with the bolts

Which kind of elcrec power that one you Handel in your hand for open, I am going to buying?

I have water dripping out of this compartment onto the passenger floor board and can’t figure out where it’s actually coming from and how to fix!!! I figure there’s a clog in the AC drain but I can find any video online to help.

how often you need to change your cv axels to buy a specialty tool like that. if u replace it often and need to have this then you have other problems such as crappy driving or car. and a flat head screwdriver would do the same. stop being a informercial troll

After removing the head cover and gasket, you'll notice there's a 1" metal spacer (not sure what it's called) that holds down the camshafts. Beneath that spacer there's another gasket that doesn't look prefab. That has failed and oil is leaking into my sparkplug tubes. I've had a hard time identifying the name of this gasket and how to replace it. Can you provide any insights? I appreciate the video. Thank you

Thanks

How have those Delphi LCA’s held up so far?

Did you have to use a tool to sync the new sensor upon installation?

Thanks dude

Hi, thanks making this video. I just did my 2012 Kizashi. For that cooler filter, I marked the upper hose and aluminum tube, then removed the two hoses, and plugged them with 7/16 bolts. I supported bottom of the transmission with a floor jack, took out the bolt and two nuts on the aluminum body mount. I was able to swing that mount up enough to get my hand in to get the filter plate out. Got it done. Thanks again!

What kind of cable kit you use to connect power to the camera ?

They make you talk like homosexual with AI using your voice to hate me via this tutorial.. Changing words to be like a black gay guy.

On your Malibu was there a knocking sound I can’t find wat my problem with my 2011

Power string pump went out on my Hyundai ELANTRA, after watching this video I’m confident I can fix it on my own with little to no experience!

Did you cut out the rail in front of the driver's temp actuator?

Good video I just removed the whole lock cylinder assembly for my neighbor's 2005 Honda Pilot so he can take the part into a locksmith to make the key turn like normal 😊 But your video helped me! Love you tube University

How do you know it’s clogged?🤔

Uhhhh sir, you might be missing a ground nut somewhere

heavy metal 🎸 🤘

They don't screw in

P0340 code is fhe front camshaft sensor u took out?

Where Did You Buy Your Two Main Tools

Hi, Sorry to Bother you... WHAT Did You Torque specs Alll the Bolts Back Down too.. 1)Axle Nut 2) Strut Bolt 3) Tie Rod Nut 4) Ball Joint Bolt & Nut Thank you, Frank

That’d do it 😅

Know that this 19 yr old and his friend are going to be following this while cursing and drinking energy drinks😭, I got dex cool sludge, need a new radiatior, wish me luck.

Well fuck😢😂😂😂

The clutch not the brakes 😂Good video man

You guys this job is very easy. Just be patient and don’t be a little sissy with the old intercooler I had no help so I had to use a screwdriver and my foot to get it out 🤣 no it does not slide out easily if the cooling fan is in the way. I had to loosen my fan disconnect the plug for it and very carefully I removed it. I had to remove my coolant hose but if ur fast enough only some will leak out and you can save most of it if you do this my way just be sure not to let the entire coolant resivor go empty or ur gonna have to bleed the system but when you remove the hose you can bend it a little bit and move it out the way. Just make sure to add more coolant and leave the cap open it should bubble that’s the air coming out the system. You may need to open bleeder screw to make sure nothing is completely trapped in the rad itself. You can buy all The parts for this like I said I needed to replace my radiator my intercooler and the hose plus I had to buy a. Bottle of coolant and my total was $845. Took me 2 days to do it because I work so it was only available for me to work on my car after work.. at 11 at night. Not to self coolant taste gross 😂😂

no fluff, no face, running mouth. just exactly what you need. people making a 20 minute video to replace filter is madness. thanks