Good Video got what i needed and the music is fine LOL mute it if you dont like the music. I would much rather hear the music over the sound of the jigsaw.
@dallaspilotcar92935 ай бұрын
actually music is depressing. but thanks for the video
@JGJeffGardner5 ай бұрын
You are welcome.
@kadettization11 ай бұрын
Super
@Ricky_gringo Жыл бұрын
jig saw plate will scratch it
@k.makininayoearle-headley8583 Жыл бұрын
Do you need to cut with wood attached as well ?
@JGJeffGardner Жыл бұрын
Hi there. The wood is only there to keep the acrylic from vibrating as you cut it. Its much easier and has a smoother finish if you use the wood. So I recommend you do it exactly as in the video.
@SteveH-TN Жыл бұрын
Thanks for sharing this video and information
@mtzmechengr5781 Жыл бұрын
Can you cut a circle shape with this jigsaw tool? Circle Diameter is 75 mm.
@JGJeffGardner Жыл бұрын
Yes you can, but you might want to cut a bigger circle first with a jig saw as shown, then use a Dremel or some sort of model maker small saw to finish off to the right size
@jessicacollins9455Ай бұрын
@@JGJeffGardner Hi there! Great video! What if I want to cut heart shapes? Which type of cutting tools would I need then?
@JGJeffGardnerАй бұрын
@@jessicacollins9455 HI Jessica, you need the same tools as I use in the video. It's just a case of drawing out the heart shape that you require onto the white sheet of paper that is placed between the wooden backing and the plexiglass and then just cutting out the shape.
@MiauxCatterie2 жыл бұрын
from a comparison video on the plexi vs metal blade, it's probably better to use the metal blade. you'll get less of a burnt edge.
@MiauxCatterie2 жыл бұрын
that music was super chillax loved it thanks
@grinshrimp82052 жыл бұрын
Horrible
@krystiandorszewski82907 ай бұрын
was thinking the same thing, i make them at work without even needing a spoon for the irish cream to sit on top of the schnapps but this dude managed to make a mess of it doing it the rookie way 💀
@genericdude65512 жыл бұрын
What is that tool you used to cut the plexiglass?
@Ricky_gringo Жыл бұрын
jig saw
@jimmiller49512 жыл бұрын
Sorry this is NOT a good way to do this so let me explain why …….. First of all the bottom shoe of the jig saw will have a tendency to scratch the plexi so at least tape it . You are better to tape around your design and then cut it. Mix a solution of Dawn dish soap and water and spray the area to lubricate is and keep the heat down and lastly , cut a little and back off then a little more and back off to keep the heat down. One last tip , title your video “ Five minute tutorial “. That’s all folks !
@goatlps2 жыл бұрын
Is that 3mm or 4mm. I am wondering how floppy 120cm/4ft (x50cm) would be as I want it to be cheap and light as possible to make a #gerbilarium. Although I would need 4 50cm L-shaped metal corner uprights to slot each panel into, and I doubt they exist.
@JGJeffGardner2 жыл бұрын
The point of this video is to show you that you can cut any thickness, even really thin sheets, as long as you support it with a backing board.
@goatlps2 жыл бұрын
I paused the video after 4:43 - I see why the video quickly ends with no close-up LOL. #PigsEar
@JGJeffGardner2 жыл бұрын
I dont understand your comment.
@lyavain27642 жыл бұрын
It's a demo, so not supposed to be perfect. He didn't spend extra time making the drawing clean or anything so idk why you'd expect the finished product to be exact. Also, it's a free vid why do so many people complain lol.
@mavirek3 жыл бұрын
As a new homeowner, my wife and I want to skin our lanai's screened wall with acrylic panels. I watched your video to learn how to work with acrylic. Do you think drilling multiple screw holes along the edges of the panels would allow the panels to be held up with screws to the aluminum frame? We even thought we would use double-sided Flex tape between the aluminum beams and screw holes to create a softer contact and some gasket effect (hope I used that word correctly). We keep watching videos to get a sense of how much acrylic can take in stress--hanging from screw holes, or what will stick to them. If you have an opinion, thanks in advance for sharing.
@JGJeffGardner2 жыл бұрын
4 or 5mm acrylic is surprisingly strong and will certainly do the job for you. What I do if I screw through acrylic is to use washers between screw head and acrylic to spread the pressure from the screw. It works very well for me.
@Doomsday-nw4my11 ай бұрын
Use clamps instead. If you want they are cheap and easily available e
@tamika12303 жыл бұрын
Goosh the vid was def what i was looking for but the music was creeping me out lol
@fintonmainz78453 жыл бұрын
Will a rear rack for a chinese scooter fit a modern vespa?
@goodlife61063 жыл бұрын
Why is this "one minute tutorial" almost five minutes long?
@JGJeffGardner3 жыл бұрын
To give people with nothing to do in their lives something to comment about
@goatlps2 жыл бұрын
It was a fair question though, Jeff. LOL!
@anastasiaantonova52293 жыл бұрын
Is there a way to cut plexiglass shapes in the middle? Like if i wanted to cut a square in the center of the sheet?
@JGJeffGardner3 жыл бұрын
Hi Anastasia, yes you can cut out a square easily too. This video I made shows you how to cut holes in Plexiglass. Cut four holes in the corner of the square you want to cut out and then use the jigsaw to cut between the four holes and you will have a square shaped hole in your plexiglass. kzbin.info/www/bejne/h3aun2yjeLuigrs
@tedsmillie21573 жыл бұрын
Cute
@hoylereyes36833 жыл бұрын
Rising dowels could have helped
@nikeairmaxneonledsign99454 жыл бұрын
Did you find this neon sign on neon factory?
@stonednyc14 жыл бұрын
Is there another way without needing a piece of wood? Also what if i need to cut a window in the middlem
@JGJeffGardner4 жыл бұрын
You can do it without the wood if you make sure you clamp the plexiglass to stop it vibrating. The wood is just to help revent plexiglass from vibrating and ruining the edge. If you want to cut a window or a hole in middle its quite simple, drill a hole thats just bigger than the size of saw blade, then start cutting from inside the hole. If you take care you shouldnt have any issues.
@sk8ternate14 жыл бұрын
super helpful video, the music felt weird and like it didnt fit with the video lol. otherwise great video!
@olavodias3 жыл бұрын
agree!! Excellent content, but the music is not helping. hehehe
@angelsxaliens34214 жыл бұрын
Where's the next video please?
@acustom66134 жыл бұрын
Was it possible to find worse back ground noise?
@JGJeffGardner4 жыл бұрын
You will be pleased to hear I have changed the background music
@landas22684 жыл бұрын
Is the wood stopping it from fusing back together?
@JGJeffGardner4 жыл бұрын
The wood is to stop the plexiglass from moving as you saw it. One of the main problems with cutting this type of material is it moving as you cut it and causing the cut to be innaccurate. The wood and the clamp holding the two pices tight prevents this.
@user-qc8uy8sb1c4 жыл бұрын
So glad I have found your video. Thank you. Question: have you ever smoothed the edges with a torch?
@JGJeffGardner4 жыл бұрын
I haven't on this one but I have before with a very hot electric heat torch.
@grady97524 жыл бұрын
Is there some important reason for that background "music?"
@JGJeffGardner4 жыл бұрын
You will be pleased to hear I have changed the background music
@jp2549583 ай бұрын
Is there some important reason that you feel compelled to comment on a users music? Is there some reason you need to be fundamentally judgmental and nasty in general, while never creating your own content? Is there some reason you feel the need to find a solution to your problem online and not be grateful for the person who showed you?
@freddy_Rahme5 жыл бұрын
😂😂😂😂😂😂😂 ah ya habile 😜
@mohamedjoma9362 жыл бұрын
Aywa, sho 3am tet3allam te3mal shots?
@nikolasimovic87037 жыл бұрын
fail
@gary72carol617 жыл бұрын
You what, Sorry What. Did you leave the microphone in the desk draw?
@morganjones-golden35447 жыл бұрын
gary72carol61 so true I could not here a damn thing😂