I was under the understanding this is the same as the game: Fast Track??? However the Fast Track game said it can be played with 2-8(?) players. Is your game, the larger game, playable with only two people? If so are there rules for when playing with two people , only???
@kaleydavis88938 ай бұрын
question! if you don’t land on the first fast track spot exactly but you land on one exactly later on in the board, can you follow the fast track the rest of the way or can you only enter the center the first opportunity from your start? I hope that makes sense. lol
@butchmiller24519 ай бұрын
What type paint do you use to get those vibrant colors?
@smack7917 Жыл бұрын
Thank you. Beautiful board
@richardhollins902 Жыл бұрын
How much is the aggravation board games I like to have one with no color I like to paint it myself you have the colors wrong you take the your color marble from the right bass and but it on the left start and go to your home place to win
@richardhollins902 Жыл бұрын
I am a low income how much is your for player board
@jephthahmcnatt7221 Жыл бұрын
😔 'promo sm'
@FreeAmerican-mm2my Жыл бұрын
Is this the same as dirty board?
@twistedgrain6001 Жыл бұрын
We had to look up what is dirty board and it looks similar but we don't use cards we only use dice to move the marbles around the board
The trick is to remove the chassis. Excellent. That you.
@ThekiBoran3 жыл бұрын
After adjusting I would suggest ripping 2 narrow strips then setting them on a flat surface and flip one around/over to see if your blade is actually at 90. If square/90 any way you flip your 2 pieces there won't be any gaps between them. The proof is in the pudding.
@realpdm3 жыл бұрын
Thanks for this. I tried the make a cut and flip it end for end method and adjust and I couldn't get it square to my satisfaction. I hasn't considered just removing the cover! Good time to clean it out too. Thanks again for sharing.
@enriquealvarez_artesano3 жыл бұрын
Thank you I have searched for years for a video like this and finally, I found it, great job now I can calibrate my Sawblade of the Festool TS 75 EQ perfectly
@alland12414 жыл бұрын
Love the T shirt
@pfboards4 жыл бұрын
I would suggest to check squarnes on RESULTS, not on the blade. Just cut two pieces, turn one around, and put them together. If the two cuts fit together, it is square.
@synthdude76644 жыл бұрын
Nice. I didn’t even think I needed to do that. Do you know how to adjust the blade depth to compensate for the track? I know this saw isn’t the same as the 55 version and doesn’t have the dual gauge. Also, do you know if the 75 has some sort of indicator to show where the blade begins and ends on the saw chassis? I’m having difficulty lining up my cut to where it needs to end other than eyeballing it
@Breal1914 жыл бұрын
I squared mine by plunging and locking in and used a protractor and made sure the blade was 90 degrees from the bottom of the saw. A square would’ve worked too.
@matdlugokecki4 жыл бұрын
Super cool video with all the things I needed. Thank you
@JustTony724 жыл бұрын
I bought one second hand. Thinking the last owner set it up correctly. Plunge the saw down and the blade was backwards like a conventional circular saw... Suspicion rising. Test cut and the blade isn't square... Some tradies.
@kyleallan44965 жыл бұрын
Hello
@bobmedic32145 жыл бұрын
You should cut the whole length of the splinter strip. Then you won't accidently register the track off of an uncut part.
@ThekiBoran3 жыл бұрын
No need. If your mark is at the end of a board and so is the track your track is too short. Get a longer track or join 2 together.
@ednaturnbull85646 жыл бұрын
I believe you got it wrong with the procedure with adjusting the 2 hex screws. What U should have done 1st was loosen the 2x bevel adj. knobs on either end of the base, this allows the saw to tilt freely. U can then either tilt the blade square against the square by adj hex screws up/down ensuring both hex screws lightly touch the base plate. Swing the saw on its bevel hinges several times then recheck for square then re-tighten the 2x bevel adj. knobs on either end of the base. I'm sorry to say that leaving the 2x bevel locking knobs tight, you have probably slightly damaged the base plate and possibly the aluminum thread the 2 adj hex screws screw into by forcing the 2 adj hex screws.
@abakken82186 жыл бұрын
Mine was slightly out - fixed it with this technique. Thanks for the info!
@twistedgrain60016 жыл бұрын
A Bakken great to hear. Thanks for watching
@Gravattack6 жыл бұрын
Nice job on your first vid, looking forward to seeing you do more. I did think festool suggested trimming the track with the blade down fully, but im not sure. But i definitely picked up some pointers for my tracksaw which is still in the box, cheers mate
@twistedgrain60016 жыл бұрын
Glenn Mack thanks Glenn
@Roger_Clarence6 жыл бұрын
Great job Brother!!! Thanks for the help!!!
@twistedgrain60016 жыл бұрын
Roger Clarence Thank Roger. Glad it helped
@daisycorta33406 жыл бұрын
oliver!
@johnmackay77896 жыл бұрын
Well done on your first video. Good tip and makes perfect sense.Think I'll give it a try on my track saw. All the best.
@twistedgrain60016 жыл бұрын
John Mackay Thanks John, I really appreciate the feedback
@rebelwoodworks43846 жыл бұрын
Great Job man. simple and informative. The comfort will come in time.
@twistedgrain60016 жыл бұрын
Yankee Rebel Woodworks thanks for that. Means a lot to hear that
@henneydesigns16936 жыл бұрын
I have this saw and just figured it was square out of the box... now i am going to run out to the shop and check. Thanks!
@twistedgrain60016 жыл бұрын
I thought the same thing until I got the message from Bill @williampatrickcustoms. I am glad I checked as it was only out by a bit but would have caused issues. I am glad this video helped you out.ThanksRob