Spina Espresso

Пікірлер

@msthetrailer8534 6 күн бұрын

Thank you we love you so much please can you tell the main problem of espresso or coffee machine and how can I fix it in the next video I will subscribe you are amazing

@coastcafeequipment 5 күн бұрын

@msthetrailer8534 sure , make sure to watch all the videos

@OsvaldoAssispereirra 26 күн бұрын

Tradução em português

@anis_majleza9510 Ай бұрын

Thanks for this video. This video is lot of useful for me.... Great job bro...👍👍👍

@salasola Ай бұрын

Thanks for the video. I'm thinking of installing an Asco Sirai pressurestat im Oscar 2. So, basically you cut the original wires, put new cable lugs with a grimping tool and then plug the lugs in the Sirai pressurestat?

@GS-vt3fx Ай бұрын

Hi great video! I have Wega coffee machine with 2 groups model EVD but I think I have a problem with the pressure as the left side pours out more water and the right side pours out less water and more steam. The pressure thermometer stays at 3-4 when it is not in use and goes up to to maximum 6 when in use it does not touch the green zone at all. Do you know where the problem could be and how to fix it please?

@coastcafeequipment Ай бұрын

Clean the jets and filters to start, then clean the flow meters if the issue continues

@christosbog2924 Ай бұрын

hi is realiable to check the element with the buzzer so if it beeps it means that the elements are ok?

@coastcafeequipment Ай бұрын

Yes

@maureenzingo3783 2 ай бұрын

if the pressure stat goes bad, and only two of the connection points are used already. Can the other points be used or does the whole thing have to be replaced?

@coastcafeequipment 2 ай бұрын

Can use the other one no problem, pull the burnt one out w pliers so it doesn't affect the good terminal by not closing completely. Don't forget to subscribe

@maureenzingo3783 2 ай бұрын

@@coastcafeequipment Thank you. And I will

@Mycutebeansir 2 ай бұрын

I'm looking for used espresso machine! Can you suggest anywhere to look for please?

@coastcafeequipment 2 ай бұрын

We sell used machines, are you in Australia?

@Mycutebeansir 2 ай бұрын

@@coastcafeequipment i though you are in italy or europe .. yes im looking for used machine but inside europe or in dubai

@fariqlye5455 2 ай бұрын

Thanks for the video. But now the machine does not heat up. Only the left light is turn on. It was working early. After two days I did try turning on and I can hear the pump working and I quickly turn off coz I thought there's no water. Anyway I add some water and turn on and it's not boiling and the left light is turn on only. Appreciate if you could assist me. Thank you again.

@coastcafeequipment 2 ай бұрын

Wiggle the float in the water tank

@SethPoore-fb2yo 2 ай бұрын

Starting up a coffeeshop and considering this machine. How has its longevity held up? Any things to keep an eye out for that may cause issues or difficulties in terms of workflow?

@coastcafeequipment 2 ай бұрын

Trouble free for atleast 5 years , watch for water level as mentioned in the video re the pressurestate

@sunilgubbala 3 ай бұрын

My wega 3 group coffee machine is not turning on.there is no power. Can you pls assist where I can find the fuse location. I will try and change it

@coastcafeequipment 3 ай бұрын

There is a fuse on the main board, unlikely to be the issue. Most common is main switch issue

@sunilgubbala 3 ай бұрын

Thank you

@dhanukatharanga4805 3 ай бұрын

❤

@dhanukatharanga4805 3 ай бұрын

❤❤

@dhanukatharanga4805 3 ай бұрын

❤

@PetesWorkshop 3 ай бұрын

The boiler is not stainless steel. It’s nickel coated copper with brass end-plates.

@user-ni1tx7ui6u 3 ай бұрын

Maybe you can help. I have a R Cinquantotto. When I turn on it makes a loud click and then silence ..I don't have computer box because it's second hand. I've replaced motherboard. The inlet solenoids, and all the wires. Checked the high limit switches and tested them. Any ideas ? Greatly appreciated

@coastcafeequipment 3 ай бұрын

Perhaps has a element relay

@jjr5918 4 ай бұрын

Bro fell down from heaven and gave us step by step instructions on how to save $15k. Thank you. I have a 3 group very similar just a bit older. Nova Evd2 model. I have nothing coming out of any of the 3 groups. Is there still a service kit available for these (gaskets/seals/rings..)? I'm in Canada.

@coastcafeequipment 3 ай бұрын

You should be able to find seals and parts for any wega.

@user-kz3hm9wc3b 4 ай бұрын

A mi no me pasa agua del estanque al motor

@coastcafeequipment 4 ай бұрын

English pls

@calebduke26 4 ай бұрын

This is probably one of the most useful videos on espresso machines that exists on KZbin

@coastcafeequipment 4 ай бұрын

Thanks alot 🙏

@ermert1403 4 ай бұрын

promo sm

@leighyarnall7346 4 ай бұрын

hi great video i have a 3 phase group 2 wega polaris have you got info to re wire to single phase please cheers leigh

@coastcafeequipment 4 ай бұрын

I'm sorry I don't. However I don't think there is any 3 phase machine. Perhaps 32amp. You can change the element or limit the elements you use.

@leighyarnall7346 4 ай бұрын

thanks for reply how much is your coffee and do you have amount i could buy to try out i live in townsville queensland just setting up shop and have a wega polaris 2 group i sorted power but have problem wont pragam left side grouyp any ideas what to fix cheers lee

@coastcafeequipment 4 ай бұрын

@leighyarnall7346 check the switch on the right have side is on while programming and off while using. U will find the switch under the right steam knob

@coastcafeequipment 4 ай бұрын

Other issue could be the flow meters , look at the video how to locate and clean. You can order online @ spinaespresso.com.au/

@user-iq5xk6ju7y 4 ай бұрын

Remember not all the time the pressure safety valve has to be replaced after it discharges, sometimes it is its normal operation especially when the pressure it's beyond 2 bars. Sometimes try just to adjust the pressure switch or replace it

@coastcafeequipment 4 ай бұрын

Correct. But not in this case

@patricklucki5368 4 ай бұрын

I have single group, same model. Works good manually but automatic shots are not working, any ideas. Would it be the main board or the button board.

@coastcafeequipment 4 ай бұрын

Could be, more info needed

@patricklucki5368 4 ай бұрын

What info do you need

@coastcafeequipment 4 ай бұрын

@patricklucki5368 could me main board, buttons, ribbon cable, flow meter. Need a tech to look at it on site, it sounds like

@samkim8309 4 ай бұрын

Do you have to empty the tank before changing the element?

@coastcafeequipment 4 ай бұрын

That's the best way

@ashkan_giv 5 ай бұрын

How can i set the wega Program setting for being auotamatic

@coastcafeequipment 5 ай бұрын

Under the right steam handle is a silver switch , needs to be down

@plurplursen7172 5 ай бұрын

need expert advice on how to clean a hx boiler. There is a layer of SUPER hard black resedue I can't get rid off. I have Used decalz, and cafiza. No effect really. And now I am going to a surface specialist in blasting with glas.

@coastcafeequipment 5 ай бұрын

Acid

@coastcafeequipment 5 ай бұрын

Usually people use acid

@plurplursen7172 5 ай бұрын

what kind of acid?

@coastcafeequipment 5 ай бұрын

@plurplursen7172 critric from what I have heard, but I haven't done it, see no reason to. So do some research

@plurplursen7172 5 ай бұрын

@@coastcafeequipment I never used citric. I just used the normal coffee decalz. Maybe my solution was not strong enough. Anyway I am hoping the blasting will remove it, and make the copper surface stronger

@plurplursen7172 5 ай бұрын

Ehm, yes it's the valve. Because half of it are missing.

@zac19751 5 ай бұрын

The pressurestat pipe might be partially clogged, the initial issue would be overheating, which made the element to work too hard, till the customer found out that is not heating.

@coastcafeequipment 5 ай бұрын

Element was burned out

@Maybaby1959 6 ай бұрын

2024 all machines now have SS tanks ha ha ha ha ha

@johnlocke3481 6 ай бұрын

What did you do @5:50 ? You were about to explain how to check that the water level sensor is working, but the phone rang and you forgot to mention what you looked for. Thank you very much for making this video.

@coastcafeequipment 5 ай бұрын

Cleaned the probe. Made sure the probe is set so the tank fill half with water

@dpledoone 7 ай бұрын

I just opened my Oscar 2, pulled a couple of terrible shots, then kept the machine on for 30 minutes and it started purging all of its water through the bottom of the machine. No leaks in the tubes that I can see, but would the OPV rectify this issue? Thanks so much for your effort

@coastcafeequipment 4 ай бұрын

Not sure where it's purging, unless you show me

@IanLandesman 7 ай бұрын

Only because of your video did I think to check if my pstat line was full of water when it wasn't turning off heating element and machine would shut off so to temp safety switch. $0 fix. Guess I have to purge it every few years. Thanks!

@coastcafeequipment 4 ай бұрын

Shouldn't have to, as long as the water level is set correctly and you clean the water level sensor every 6-12 month

@chulolo997 7 ай бұрын

The level probe stick will not tighten even after I screw the bolt, why is it? Yours seem to stabilize at any height that you like

@coastcafeequipment 4 ай бұрын

Perhaps the plastic sleeve has fallen down

@Pauly5150 7 ай бұрын

Great videos. I have wanted to have a go at repairing an old machine, and this the kind of help that is perfect. Once I find a donor machine for a bargain that is. Thanks

@b_o_b_a_ 7 ай бұрын

I just acquired one used and I'm having issues where nothing really comes out. Would you know what the issue is?

@bobok760 8 ай бұрын

I agrees there is no sense to buy it, too many flaws that make extraction process worse

@muhamadyunus8603 8 ай бұрын

Thank you

@hugobot5 8 ай бұрын

really easy to follow , info and method really helped me with a totally different problem , will look thru your other vids too , my current prob is old Astoria Argenta single not heating ...

@coastcafeequipment 7 ай бұрын

Check over temp, element , pressure state

@johntindog 9 ай бұрын

Hi You say the Rocket is a bit overrated, what do you recommend, I have the Breville 920 and have had it for over 5 years and have been very happy with it. But when it dies I was just thinking what I might look at buying. Kind Regards John

@amanyafatafishing01 9 ай бұрын

Thanks sir for this video

@RMD992-f2n 9 ай бұрын

please help me i have a rocket apartamento that start overheating so i bought a new pressure stat... i am having trouble installing the new one as the old one does not want to twist off.... its seized or something. i tried putting wd-40 on it and it stil wont come off. what can i do to get this thing off? have you ever experienced this problem? thank you!

@coastcafeequipment 9 ай бұрын

Use multi grip on pressurestate

@RMD992-f2n 9 ай бұрын

@@coastcafeequipment all the pressure stat is doing is twisting but the screw underneath is it not coming out. I don’t know how to describe it … I tried everything

@coastcafeequipment 9 ай бұрын

Hold it w multigrips or take it off together with the copper pipe that connects to the boiler, easier to work on when out of the machine.

@RMD992-f2n 9 ай бұрын

How do you remove those cables and wires attached to the pressure stat I just can’t get them off and I’m pulling very hard

@coastcafeequipment 9 ай бұрын

Use a flat head screwdriver to lever it out

@RMD992-f2n 9 ай бұрын

oh by the way i got the cables off but now i cant twist off the pressure stat it seems like its seized or something? ive applied so much force that i actually broke the old pressure stat. how do i remove it is it supposed to easily twist off? i've tried evreything...@@coastcafeequipment

@SimonDiderrich 10 ай бұрын

Most of the other videos seem to just install the OPV up the top so you simply just pull off side cover no need to turn upside down or run return hose into tank as they place a t junction down the bottom for the water return eg kzbin.info/www/bejne/aqjIinegnbacb5osi=6aZUZ48pU53_uEk0 Is there any advantage to having the OPV closer to the pump like youve done?

@masudnordin 3 ай бұрын

Yes, I would like to know as well

@gdubwilks 11 ай бұрын

What would cause an Isomac Millenium 2 to power on but the lights showing the boiler is heating or heated never come on? So no hot water.

@ddavidi81 9 ай бұрын

A faulty heating element, a faulti relay or solid state relay, a resettable fuse.

@gdubwilks 9 ай бұрын

@@ddavidi81 hey appreciate the reply! I changed the heating element, pressurstat, boiler thermostat, and solid state relay a few weeks ago. Still not working. My next things to try are the control box and/or the 2 way solenoid. This thing has me pulling my hair out!

@ddavidi81 9 ай бұрын

@@gdubwilksI am sorry that you had to change so many things. A multimeter would have helped a lot here. You start by checking one by one, from the bottom. The heating element, pressurestat should show a closed circuit, or a certain resistance if you are using an ohmmeter. Solid state can be switched on with some volts. If no 110/230V (do not know if you are in USA or EU) is comming at the heating element, the problem can be isolated to the control box (you said you changed the solid state relay, so I assume it is working). In the control box, usually there´s a relay which control the solid-state relay. When you first switch ON the coffee machine, you should hear a click. If you hear the click and still measure no voltage at the heating element, your problem is a ca. 5€ problem. Change the relay with the same type, and you are done.

@avibm948 Жыл бұрын

Its true. But the price reflects it. I need to do the OPV myself. Have leaks all the time.

@TheMASDrummer Жыл бұрын

hey mate, which city are you working from?

@coastcafeequipment Жыл бұрын

Morisset nsw

@evakeizers9670 Жыл бұрын

For an experienced technician it's like a breeze of air.

@user-nw9wv1ls4y Жыл бұрын

I want to change the OVP valve on my 1,5 year old Oscar 2, but am a little concerned about residual water in the machine circuit when I turn the Oscar 2 over for adding the valve. Is there anything specific I need to do before playing around with the pump other than removing the water tank and letting the boiler cool down?

@coastcafeequipment Жыл бұрын

That should be fine. Nothing else required

@user-nw9wv1ls4y Жыл бұрын

@@coastcafeequipment the elbow piece isn't moving at all. I tried pliers on the elbow piece and a wrench on the gold piece, but it won't move and I'm afraid of breaking something. Do you have any advice?

@coastcafeequipment Жыл бұрын

Wd40, and elbow grease ( more force) . They use liquid seal tape can be a little hard to crack

@yamcha111 Жыл бұрын

I believe they have updated the machine, but yeah that sucks

@leonardau7048 Жыл бұрын

TBVH 15 bars of pressure should not cause leaks. How do I know. Cause I've done it multiple times. It was a gasket issue

@coastcafeequipment Жыл бұрын

A. Yes it does leak if you want coffee with crema. B who wants to extract coffee at 15 Bar? Not me

@leonardau7048 Жыл бұрын

@@coastcafeequipment not here to fight but you do you.

Ең жақсы KZbin

Пікірлер