Пікірлер
@Cryptotrader0627
@Cryptotrader0627 7 күн бұрын
Bhai mujhe bhi pcb board change karna h apni iton me ye part kaha milga delhi me
@RafiqBlog-zp3md
@RafiqBlog-zp3md 6 күн бұрын
@@Cryptotrader0627 are you from India?
@Cryptotrader0627
@Cryptotrader0627 6 күн бұрын
@@RafiqBlog-zp3md yes
@nunolourenco338
@nunolourenco338 16 күн бұрын
Not really fixed if you don't tighten the clamp :/ That's the difficult part, especially on the other (hot) tube. Mine comes out every month!
@kurien737
@kurien737 22 күн бұрын
The water tank unit with rotary knob of thermostat,is just held by 1 screw in front...opened 2 screws at rear..!! Is it held by a clip or screw at nose of iron..!!! No idea...!!
@kurien737
@kurien737 22 күн бұрын
Will tapping it from rear help ,or just lever it, to seperate tank from hot plate bottom..??
@RafiqBlog-zp3md
@RafiqBlog-zp3md 21 күн бұрын
@@kurien737 where are from? The thermal fuse is attested by the heater plate. As a result buy a new heater plate.
@kurien737
@kurien737 22 күн бұрын
Thanks for replying..I need to reach the thermal fuse,cannot find the attachment/screw ,to seperate tank from heater sole plate,is there a screw behind front spray nozzle? Once i know where the screw in nose is,will open remaining and get access to thermal fuse...!! But i can't find that screw or attachment...?? Pls advise...thank you...!!
@kurien737
@kurien737 23 күн бұрын
On my iron light is flashing ok..relay comes on with click, so pcb is ok..but no heating, so mostly its thermal fuse at bottom...inside of heat plate..
@RafiqBlog-zp3md
@RafiqBlog-zp3md 23 күн бұрын
@@kurien737 where are you from? If you confirm PCB is good.please check Thermal Fuse.If Thermal Fuse is not good or heater plate is not It wouldn’t be heated up. Must change your heater plate.
@kurien737
@kurien737 23 күн бұрын
I have same iron..think thermal fuse at bottom sole plate is open, needs to be replaced,have opened majority of unit..at nose tip the tank unit part ,is not coming off, believe a hidden screw or latch is there ,am at a loss how to open further ,only then can i open last part, sole plate and get acess to thermal fuse ,removal and replacement..can you help..??
@n.aminr.7175
@n.aminr.7175 24 күн бұрын
Where can I buy that part? What the name or part code?
@RafiqBlog-zp3md
@RafiqBlog-zp3md 24 күн бұрын
Are you from Saudi Arabia? If you are from Saudi Arabia these parts are available at wifex, Jeddah.
@mishalfatima5429
@mishalfatima5429 Ай бұрын
your services location??
@RafiqBlog-zp3md
@RafiqBlog-zp3md Ай бұрын
@@mishalfatima5429 Thank you so much for comment. I have no own location. I am working as a technician in a famous company.
@xxzxx21
@xxzxx21 Ай бұрын
جناااااات ياعشقي
@karlunjohnnycheung2662
@karlunjohnnycheung2662 Ай бұрын
The music is too loud!
@RafiqBlog-zp3md
@RafiqBlog-zp3md Ай бұрын
@@karlunjohnnycheung2662 I will keep it in mind next time
@WaleedKM98
@WaleedKM98 Ай бұрын
Can you help me please.. I want to turn off the bottom heater. What is the easiest way? Should I disconnect a specific wire or what do you think?
@RafiqBlog-zp3md
@RafiqBlog-zp3md Ай бұрын
@@WaleedKM98power switch is the cancellation button of over heating or heating. After taking the required amount of copies, if there are no more copies, then turn off the power switch.
@WaleedKM98
@WaleedKM98 Ай бұрын
@@RafiqBlog-zp3md You did not understand me well. I always drink iced coffee and put ice in the glass jug, but because of the heat of the bottom heating, the ice melts quickly. I want to cancel the lower heating completely, Because it works while preparing coffee, and immediately after finishing the preparation the ice melts completely due to the heating from bottom and there is no benefit in turning it off immediately after finishing, it is just too late and the ice melted. In short, is there a way to turn it off or cancel it or is it not possible by cutting a wire or something like that?
@nourahkhalid
@nourahkhalid 2 ай бұрын
Thank you
@RafiqBlog-zp3md
@RafiqBlog-zp3md Ай бұрын
@@nourahkhalid you are welcome
@Bagdart
@Bagdart 3 ай бұрын
How did you opened it?
@RafiqBlog-zp3md
@RafiqBlog-zp3md 3 ай бұрын
@@Bagdart are you facing motor stuck. Open top cover and 5 screws then clean
@Bagdart
@Bagdart 3 ай бұрын
@@RafiqBlog-zp3md no, I just realized it’ll open when pressing the start button. Your video helped, thanks :)
@uchclan
@uchclan 4 ай бұрын
Still need help
@RafiqBlog-zp3md
@RafiqBlog-zp3md 4 ай бұрын
@@uchclan please tell me.what kind of problem did you face?
@marvin_78_nice_lol75
@marvin_78_nice_lol75 5 ай бұрын
So hört der sich normal nicht an!
@pavlinapeeva5837
@pavlinapeeva5837 2 күн бұрын
Because it lost its sucking ability
@md.rafiqulislam5442
@md.rafiqulislam5442 6 ай бұрын
Anyone can comment here to repair coffee machine *any problem about Philips coffee machine 🥰🥰🥰