I replaced the fuel filter with help of your video. But now car not starting. All connections are ok
@MechanicAnoop13 сағат бұрын
That's funny now. :) Did you prime the filter? Turn ignition on and off two three times and crank the engine until it will start. Also observe the pump noise when you turn ignition on.
@black-catmusic36193 күн бұрын
Oven cleaner is also possible I have heard.
@MechanicAnoop13 сағат бұрын
Sure it could be. A guy did a video about dpf cleaning using Coca-Cola, toilet block cleaner and so on.
@user-bd3sc7di9g4 күн бұрын
Why change fuel filter ? What is the problem
@MechanicAnoop4 күн бұрын
Stuttering and performance issues.
@user-bd3sc7di9g4 күн бұрын
@@MechanicAnoop is it possible for it to idle out of this?
@MechanicAnoop4 күн бұрын
I don't understand your question.
@user-bd3sc7di9g4 күн бұрын
@@MechanicAnoop my car stopped work at idle
@user-bd3sc7di9g4 күн бұрын
@@MechanicAnoop is the problem with the fuel filter
@febinbiju314410 күн бұрын
👍
@crisgravel838712 күн бұрын
Awesome video!
@MechanicAnoop12 күн бұрын
Thank you!
@umairjiPooran-nm5gk15 күн бұрын
acha kam ji
@thabitaanoop670716 күн бұрын
Good one baby ❤❤❤
@thabitaanoop670718 күн бұрын
❤❤so good baby 💪🏻
@bigsid198419 күн бұрын
Yeah going down road wheel going opposite direction
@nolamusik293620 күн бұрын
Please, what brand power steering fluid is good? I have a 2014 subaru outback
@MechanicAnoop19 күн бұрын
Buy ATF from Valvoline, Castrol or Meyle.
@stevecobb259223 күн бұрын
And they yoused to do this on america with quality american made parts , then china took over and the manufactures had to move elswhere because of regulation . Parts became more expensive because of constant failure. Taxes got higher, and the polaticians were more emboldem and citizens wound up in jail. Am i wrong , prove it
@legistermusic734225 күн бұрын
Nice 🇯🇲...
@Steve088525 күн бұрын
Slow it down and let's see how this kicked your butt 😅
@mral444926 күн бұрын
Did anyone else notice no gasket or rtv on reassembly? Its gonna leak like a seive. And yes, also all the hammering looks like something not right.
@MechanicAnoop25 күн бұрын
Look again slowly, the gasket you can see(black colour) it is not hammer It's mallet, it was because of the bearing fitting.
@johnthornton186526 күн бұрын
so for 40 minutes work I paid £320 GRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRRR!!!! Great video mate, will sub and check out your videos before i pay a garage. Thank you
@MechanicAnoop25 күн бұрын
Thank you so much for the support mate!
@ESSA2026 күн бұрын
Brother would fuel filter being clogged would it stop the pump from working? The car isn't starting I cannot hear the fuel pump at all.
@MechanicAnoop26 күн бұрын
Hello brother, I never had such experience. Even if the fuel filter is clogged the fuel pump must turn when you turn on the ignition. Have an inspection, start from the fuses and followed by fuel relay. If the vehicle has more than 200,000 km check fuel pump itself.
@ESSA2026 күн бұрын
@@MechanicAnoop car done 60k, I'm going to check fuse and relay. How would I test the fuse and relay? Test light? Would multimeter also work?
@MechanicAnoop25 күн бұрын
You can use multimeter for fuses so that you won't need to remove fuse, For relay use a 9V small battery.
@thabitaanoop670726 күн бұрын
Loved it baby 😍💪🏻💪🏻
@AbysmalRapture27 күн бұрын
Atleast he didnt wag his finger this time
@Archpimp28 күн бұрын
How do those tiny rings/shift collars? not snap from torque? They seem so delicate compared to the beefy gears.
@MechanicAnoop25 күн бұрын
Those rings are like cork and bottleneck, it works based on friction.
@PatryckGustav0128 күн бұрын
Esfregou mais de um lado que o outro isso aí se que faz chama-se plaina não desnivelamento
@chevecrazy454ss29 күн бұрын
Definitely not the way to do it but if you don't have much money or acces for the correct tools then its Definitely the way to do it😅
@philpotter464029 күн бұрын
How to destroy a new wheel bearing 😂😂
@abdieljurado302Ай бұрын
You need just 1 bottle?
@MechanicAnoopАй бұрын
Yes. 1 litre is sufficient in most of the hydraulic power steering systems.
@Mr_BUSINESS_24_7Ай бұрын
use the same shims ? did you replace any other bearings ? why all the hammering ?
@MechanicAnoopАй бұрын
Yes Same. It's not hammer, It's called as mallet.
@thelazyhandyman8581Ай бұрын
Good job man! Respect your hardwork
@MechanicAnoopАй бұрын
Thank you so much man!
@tiredhub3270Ай бұрын
It worked like a charm! P0405 is now gone!
@MechanicAnoopАй бұрын
I'm so glad it helped you!
@ravindrabobbili9338Ай бұрын
Superb video, no music,no nonsense, simple video, full information. Thanks to videographer
@MechanicAnoopАй бұрын
I'll convey, thank you so much!
@ravindrabobbili9338Ай бұрын
Perfect video
@MechanicAnoopАй бұрын
Glad you think so!
@dennku1764Ай бұрын
Pfusch am Werk
@RushlonmechshowАй бұрын
What is the cause why u replace the coupling sir?
@MechanicAnoopАй бұрын
Clunking noise in low speed, (speed of parking)
@aurelienz1422Ай бұрын
What a great job! It's look so easy when we look at you! But for sure is not! Great knowledge and great hands. Thanks for the share from FRANCE. Have a nice day
@MechanicAnoopАй бұрын
Such a big compliment! Thank you so much Aurelinez!. Have a nice day to you too. 😊
@bobychandra5742Ай бұрын
Andq merusak bearing bila memasang dengan cara begitu. Tak lama setelah penggunaan pasti akan timbul bunyi berdengung.
@hugotrevino6153Ай бұрын
Cliente pidiendo garantía en menos de una semana
@TheMunchieGangАй бұрын
So instead of just a press.... you need a torch, saw, brake cleaner, a mallet, screw driver, and a drill?
@MechanicAnoopАй бұрын
Yes.
@danbrannbacka3769Ай бұрын
What a waste of a good bearing...
@ShreddylifeАй бұрын
should have torched it and it would have came off a lot easier
@MechanicAnoopАй бұрын
You are right. But I was afraid about the hardening of the differential.
@ShreddylifeАй бұрын
@@MechanicAnoop I don't think its going to harden the metal from just torching it just to get the metal to expand the bearing. You would have to get the metal up to 800C or 900C for that to happen.
@stu6885Ай бұрын
yer doing it wrong lol
@jimbob1800Ай бұрын
I would have bought a strut knuckle with the bearings already in it
@user-fe9br8kj6xАй бұрын
Нельзя зубило втыкать между цапфой и внутренней частью подшипника
@luckympho_mАй бұрын
What did you install on the stems before installing the seals?
@MechanicAnoopАй бұрын
Valve seal fitting protector sleeves. Without this valve seal would be damaged when sliding through the valve stem.
@deltatuningАй бұрын
Looks like ford Focus
@MechanicAnoopАй бұрын
FORD MONDEO MK3
@dmotor13Ай бұрын
Hard work
@vusindlovu88972 ай бұрын
Wrong!
@danielmuller78912 ай бұрын
Thank you for this video !
@MechanicAnoop2 ай бұрын
Glad it was helpful!
@Katenochku2 ай бұрын
Греть подшипник это круто 😂
@kostadinpantev2 ай бұрын
So you need WD40, not a press.
@user-jf6yk4de4t2 ай бұрын
Нельзя по нему скучать вот чисто под прессом надо подшипник загонять😆😆
@user-jf6yk4de4t2 ай бұрын
Не успел установить уже испортил стучи стучи побольше стучи толку нет от твоего подшипника есть постучал по нему молотком когда устанавливаешь