They suck too work on

Auto tranny fluid. The cooler pipes in the rad gone.

Who put mac and cheese packet in the radiator again

Blown head gasket

Oil cooler is my suspect

Sir please help me

Hello sir big fan 🎉

Hello sir S-125 genie pcon software update video ❤

Hi sir Please S-125 genie machine software update video......

Do you insert the lock pin in the engine and that’s it?? Or do you insert the lock pin and rotate the engine till the lock pin falls into a hole??

Good work

Good work

Très intéressant

Very helpful❤

Hi

Hey I just acquired a 1999 Genie Z34/N22 (electric) and the only way it will operate is if I use the auxiliary power/pump switch, it doesn't matter if I try from the basket or from the ground controls. If I try to operate it normally, I just hear a clicking sound whenever I try to enable any function. I believe the alarm is also on whenever I turn the key on, It's just that the alarm is barely audible as I am guessing the alarm is broken. Any idea what might be causing it to only work from the auxiliary pump/switch and clicking when I try operating it normally? Batteries are fully charged. Thanks in advance for your time if you see this. cheers

There isn’t any video on your channel saying how to fix it

Thank you, sir; good job. I have a problem with Genie S-125, "Primary Boom Ext/Ret Flow Valve not calibrated" how do I calicrate ? I hope you can help me SIr.

Hola 'número para comunicarme

Teléfono para consultarle

Holle

Hello, you have free webgpi installation exe with Key?

Short circuit of the P-CON steer right switch at system startup.👍

God tei do video! Gostaria de saber qual é a tensão dessas duas ficha? Eu tenho Refo escavadeira so que ela Não pega

Will it be a good temporary fix to remove the thermostat?

Is the sensor in the same spot on a s80 genie

Hello, Is possible download software webgpi with Key?

GN SIR HAVE A GENIE S60 HAVING SOME CREEPING IN DRIVE WHEN U START IT AND AS SOON AS U CUT IT OFF GETTING A FLASH CODE 54 ALSO NO DRIVE OR REVEARSE EVERYTHING ELSE WORK

Nice work! Very informative

Hi

Why does this occur??

where can i download web gpi software

Snorkel tb126j : bus error Xin hướng dẫn tôi cách khắc phục Xin cảm ơn

I had that code and found was the p con decal to enable the lift or drive function was stuck down enabling the function at start up and throwing the code change the decal turned it off and back on and everything worked good after that

Hello, how can i fix this error?

Good job there sir❤️👍, please sir I have a problem for s125 sir the third boom is not coming out sir please sir what will i do sir to fix it sir? Thanks for your understanding sir.

Hi great video 👍👍👍 do you know what sort of resistance should be on those coils?

Press what for 10 seconds? Just pulling out on the red knob or pulling the red knob and holding down the lowering switch as the same time for 10 seconds? Does this procedure work if you have a lower cylinder that fully lowers but the upper two cylinders do not?

Unhook the beeper please. I can’t hear what you’re saying

How to do calibration for jib sensor on z135 ?

Where is the thermostat located on the engine

If your just clearing saftey switch faults get into options by holding enter for 5 seconds while pulling estop, then press " - - v v " then enter until you see clear saftey all switch faults.

Thanks I love this sir. Sir please I want to ask you something about the password you forget sir, what was the correct answer?. The second one is how will I get all the cables for the computer, and the software for Genie sir thanks 👍

Thanks, but how will I solve the problem of p11, p30,p39. On z135/70.Please sir I need your response on this sir thanks.

hi, same problem on a s3226e, display shows sensor problem, i check all sensors and they seems to be working, putting out about 2.5 volts to computer, the pothhole sensor 2 is sending 24V to the computer or module. the joy stick has analog voltage going to the main module or computer. any ideas? or tips? other thing there is a circuit from key switch running 24 positive voltage, but schematin says ground control circuit. and i dont get ground to solenoides unless i turn the main power on i thing. meaning the big cut out switch. schematic is called ANSI. also cant find the, and probably from factory the pressure sensor is missing, only harness pig tail is there. i will appreciate any help. or info.

Great 👍

Por favor poderia passar a medida desta ferramenta desde já muito obrigado

Félicitations et bon boulot.

DE10 I think

I have a 5205 John Deere tractor and I changed out the water separator filter a elbow turn off nob into the pump where there is a primer above. Long story short we are dead in the water cant start . Tracked everything back to fuel pump and its going in ( fuel) an still no go.. its going into but not feeding into each injector lines.. all dry...