What is the write and writefast difference between
@rahimullahjalal48723 ай бұрын
which Mission Planner version and type is this?
@bluecavemen4 ай бұрын
good job on placing your cursor where we think it is haha
@NS-niws4 ай бұрын
same question
@bluedog96015 ай бұрын
How is the hook on your plane setup mate.
@gm7436335 ай бұрын
What is kittyhawk? I didnt see how you invoked it or how it relates to mp sim. What i'm looking for this sim to do is simulate my heewing t-1 vtol using my pocket controller in free flight. Just like in reality outside. I want make sure the parameters in my t-1 vtol will work properly without crashing again during transition to fw flight.
@DroneBawse5 ай бұрын
just cut this out
@MikeLampick5 ай бұрын
nice job
@adammontgomery7980 Жыл бұрын
Are there any alternatives? I'm using Ardupilot in a plane, but I'm really dissatisfied with Mission Planner. It might be some of the slowest software I've ever used
@jesse6249 Жыл бұрын
Im looking to get into this field for security purposes is there any settings to launch the drone at specific time intervals or say every couple hours?
@kyleberger862 Жыл бұрын
Hey, we use mission planner for our hydrone boat. We were working right next to a high security air field. Every time we tried to run a mission it would disarm our auto nav box. Have you heard of anything like this. Thanks
@airdroperua Жыл бұрын
@iwontreplybacklol7481 Жыл бұрын
Big build up for a launch and then cut the video...boooo
@baitku5955 Жыл бұрын
Do you have a link to download this software?
@Zahmetbey Жыл бұрын
bro this ardu pilot gives such an error ' cyggcc_s-seh-1.dll was not found' what should ı do
@ismailkalkan2383 Жыл бұрын
hello brother, I have a question, how do you find the pulling force with the scales,,,that is, how many times the weight of the plane you will fly should be, the weight you measured in the tire,,,I don't know if I can tell you,,my plane is 1kg,how much should I pull the tire,thank you for your answer in advance
@Sleeperknot Жыл бұрын
Mouse pointer was not following what you were explaining. Found it a bit difficult to understand
@Chris-vc1dh Жыл бұрын
hey, how to setup radio to be able to use?
@prasannakumarreddy6136 Жыл бұрын
I have a doubt while creating the auto waypoints in the grid its showing the waypoint numbers only even numbers like 2,4,6,8,10,12 in my mission planner if select the spiral grid in grid options then its showing waypoint numbers normally as 1,2,3,4,5 ,6,7,8,9 what might be the issue please help me to sort it out
@AleemSiddiqui100 Жыл бұрын
Hi Max, Please simulate the SWARM Drones as well, as also the leader-follower configuration
@Nolan.Gurule2 жыл бұрын
You swallowing your spit is agggrrraaavating
@induchandran82072 жыл бұрын
Could you please make a video on multi drone swarm?
@sultanmia38952 жыл бұрын
Nice ☺️
@nestorguillermodelcastillo87662 жыл бұрын
TENDRAS LOS PARAMETROS DEL DRON PARA PIXHAWK Y MISSION PLANNER
@idanlevovsky85852 жыл бұрын
I know I'm six years late but I'm an electronics student, I and other friends are trying to build a version like this for the final project. We'll be happy to know where you bought the package itself (we only need the plane without the components)
@dronepilot260rc5 ай бұрын
Ali Express
@ulrichsucker27122 жыл бұрын
what kind of Checklist did you use?
@StreetMisfit2 жыл бұрын
Great stuff. Taking a UAS class now and you’re very good at being thorough about the process
@minhajsixbyte2 жыл бұрын
great video, only if the cursor was in correct position.........
@andreapetrachi4672 жыл бұрын
when you create a mission, the pc you bring with you must have internet connected or can it be off lne?
@benzviely94322 жыл бұрын
great video! thanks for sharing. can you please explane how to create spline wp in mission planner (vtol)?
@alexandrelarribau40832 жыл бұрын
Hey, what are the two options for overshoot (m) in the grid options ? could you explain this to me breafly ?
@iremdp11992 жыл бұрын
I could not see the mission planner latest version vtol departure in the section where we selected the departure please can you help me?
@iremdp11992 жыл бұрын
how can we set vtol take off??
@indeterminatedude73342 жыл бұрын
thanks man
@3drccustombeasts3812 жыл бұрын
Hello. could you kindly tell me if there is a way to adjust dead band like there is in betaflight. I've been discouraged from using my APM because of drifting and I know it could be corrected but no matter how much research I do I can't find a way to set dead band in mission planner
@albertorafaelmuyacosta38372 жыл бұрын
any tutorial for fixed wing VTOL ?
@emircihanpolat8 ай бұрын
@albertorafaelmuyacosta3837 Hi. Did you find any tutorial for fixed wing VTOL?
@gm7436335 ай бұрын
Heewing ranger t-1 vtol.
@paulmason1142 жыл бұрын
What glue did you use to put orange wing joiners on
@LoudRC3 жыл бұрын
I believe the placement of the antenna for you X8R receiver is suboptimal (seen at 1:13) The FrSky RX uses a pair of antenna as the receiver contains signal quality software that allows it to use which ever antenna it believes has the better signal. Ideally you want the antennas to be 90° to one another, one vertical and the other horizontal. This will allow the highest quality signal irrespective of aircraft orientation, or angle to the Tx. Other than that it's an excellent video, thanks!
@SkLearnFun3 жыл бұрын
at each point we need to hold the drone for 10 sec , how to do it please tell me
@pawebazylewicz75743 жыл бұрын
When you will continued the multrotors tutorials (for example starting, saving and loading the missions, settings of the gimbal for mapping, flight mission changes)?
@johntan68543 жыл бұрын
hi sir, your video is very useful and interesting, but i have a question, i mean i have met a error when i click on writeWP after pointing the WP, which the error is ( there was an expected error " Timeout on read -setWPTotal " ) and something, may i know why and how to solve this issue? thanks in advanced and hope to receive your reply soon!
@gosuvenu62703 жыл бұрын
What API is using in Mission planner ?
@loreleizinn2283 жыл бұрын
Your cursor arrow did not follow your points of topic in this video.
@d_praz59463 жыл бұрын
Sir, do you have any tips for the Settings on the mission planner to mannuver planes sharper and more agile?
@youngcheoljang6523 жыл бұрын
Thank you very much for your lesson. i am learning a lot from you. From: South Korea
@mikelarin80373 жыл бұрын
More details on the plane hook please
@vaggx35473 жыл бұрын
can we modify the communication links and the frequencies of the links? i am trying to implement mission planner for real-time high speed chasing operated by a network. Can i get information regarding the mavlinks established and the exchange info protocols etc?
@sherwoodp27383 жыл бұрын
I'm new to Pixhawk, Mission Planner and VTOL but I'm a quick learner. My MP default for Flight Planning does not have the "VTOL_TAKEOFF", "VTOL_LAND" or "DO_VTOL_TRANSITION" options in the Command drop down list. How are these items added?
@mecantronic3 жыл бұрын
Im looking for the same thing. It seems that if you are connected to your drone, and if this is config as a quadplane, it does give you this option in MP. Bit 1 and 2 seem to imply that the default take off and landing is VTOL: ardupilot.org/plane/docs/quadplane-parameters.html?highlight=vtol_takeoff