Such a great idea with one exception. Where are you supposed to find a RR rail?
@elipsonj10 ай бұрын
What type of Redneck shit is that???
@peterhou499811 ай бұрын
with the way, I finally break the bead and removed the stuck tire. I use a 3 feet of 4x4 wood instead of the metal railroad track.
@doit5000 Жыл бұрын
Did he just say shizzle about six times?... And boom shakalaka?...all in this less than 10 minute video. Well shizzle my biscuits and BOOM SHAKALAKA... that's how we roll.🚂🎢
@eddierodden Жыл бұрын
If this is an end of life tyre, this is okay because otherwise the tyre is getting crushed too much.
@arthurevans5608 Жыл бұрын
2023=Liked, Thank you for the upload, i maybe gonna try this on a harley 16x3 rear factory spoke rim. Take off tire on rear rim is new and install on a new rear rim duh? Ive tried c clamps and bead spoons but this make it look easy for those hard to break resting in the weeds ill git to it later kinda situations.
@tomsparks3259 Жыл бұрын
Well done!
@silverdragontaylir8252 Жыл бұрын
Genius
@martinkoche4375 Жыл бұрын
Great job you are real crafty thank you for sharing this Sir
@davezoom2682 Жыл бұрын
You would do better with some soap as lubricant
@Edward-iy4mi Жыл бұрын
sweet monte
@dalefancher2 жыл бұрын
Thanks for sharing. You even picked the most difficult tire to break. : )
@bobqwhite12672 жыл бұрын
I'll tell you a easier way to break the bead . Diesel fuel yeah I know sounds like 🐂 but saved me. Stay blessed.
@brucekuprowski57072 жыл бұрын
Turn the Music Off
@edwingonzalez75342 жыл бұрын
Kind of stupidity...
@williepelzer3842 жыл бұрын
Now you have another junk tire off your pickup, after you run the chisel thew it . Boom Chuck allucka
@jasoneaster1339 Жыл бұрын
Thank goodness it hasn't happened yet 😂 Thanks for watching
@colestowing86952 жыл бұрын
I was really impressed by this guy's energy level, then I realized I was watching at 1.75 speed😂
@Prash1c2 жыл бұрын
Awesome and nice job! :) Thanks for the video! Wondering if the rim's bead rests or flange gets beat up from the chisel? In any case, nice job! :D
@jeffrandolf56735 ай бұрын
Yeah... don't do this with $2000 BBS STYLE 5 rims
@AaronBilger3 жыл бұрын
I used a bottle neck jack and the back end of my tractor worked great on my 10 ply truck tires
@sdsturges24643 жыл бұрын
how do you get rid of all the old tires ?
@caliman26392 жыл бұрын
He burns them.
@jasoneaster1339 Жыл бұрын
I took them all to the county district waste management and paid $3 each. Worth every penny to get them off my property. Thanks for watching
@sethmcgill37743 жыл бұрын
Lube is your friend!
@caliman26392 жыл бұрын
So is your writing hand 👌
@timothydean3 жыл бұрын
I ain't got no rail road rail but I can get one from union Pacific.
@ToxicSocietyTroll3 жыл бұрын
If the tire is trash, why not just cut the tire off the rim? Cutting tires is very easy.
@SurvivalInFlames2 жыл бұрын
You’ve obviously never tried to cut a tire off a rim, it’s a huge pain in the ass.
@yappiesinfo41122 жыл бұрын
Not the f....... Easy try it with a sawzall
@jasoneaster1339 Жыл бұрын
Tires are a pain to cut off rims even with Sawzalls. This method was moving along pretty quick so I stuck with it so I could get it done and over with lol Thanks for watching
@philtowle46832 ай бұрын
Cut sidewall with knife, narrow slitting disc on angle grinder through bead.
@somewhitedude0118 күн бұрын
LMAO
@manisaro93193 жыл бұрын
Time waste
@jasoneaster1339 Жыл бұрын
Sorry you think that. This method Worked very well for me on every tire i worked on. Thanks for watching
@Edward-iy4mi Жыл бұрын
no time waste ,trash to cash
@philkillen50164 ай бұрын
I'll take that Monte Carlo please.
@geraldmcclellan75643 жыл бұрын
Did that method damage the rim,because I want to use a rim I want to try your trick on, I know you doing cleaning in your yard, and I figured you scrapping those rim,but this is genius if it doesn't hurt the rim😉👍
@erikscotmanie96523 жыл бұрын
Gerald McClellan as your photo shows a boxer a reply for you re your comment as reply from a kickboxer .... if you get my reply - if you want too take a tyre off while sitting down or standing at a table or work bench as if u really need too save the wheel without and very little damage & save money& save fuel cost and time ... try this one - tools required 1-sharp knife ,2- a good pair off wire snips ,3 -a decent medium sized flat headed screwdriver, 4 - a bit off rubber or cardboard as too prize your screw driver on later on in u can remove a tyre Free in without all off this hassle in puffing & blowing .... now you have too cut the main part off the tyre off all the way round the side off the tyre on both sides just above say the little close lip rubber bit just a few mm away from the outer side rim off the wheel ...ie leaving only a small amount off the inner rim off the rubber tyre that’s attached too the steel or alloy rim on - can be done in “second “... as there are about 10-12 bits off wire a few mm thick inner rim - as that’s the main issue this guy is having is how a tyre is kept on a rim .... so now you cut into the rubber that’s left around the rim like a half moon 🌒 at one location -shape 🌙 push in your screw driver prize out a single loop off wire in cut - should get a few wire bands at the same time then pull wire away a little in then cut a little more rubber off the inner rim in continue process ie prize out wire in cut till your right throw all the wires on the tyre rim - then there a little inner rubber left ...once you have done it then you will truly understand a how manufactured tyre is made as after that u simply remove the bit off the rubber rim still attached .... all say there a few other ways too remove a tyre free in faster ... it’s possible too also use the weight off a vehicle with a bit off metal attached too the tow-bar bolts main frame where the tow ball is located fixed in all you do is use the weight off the vehicle as like a piston compression process as using a trolley jack too lift up& then lower down the vehicle weight as pounds off pressure ... using just a bit off metal shaped a bit like what a real garage uses too push the rim off - down .... in as this guy did use crow bars but he would have been better using one at each side off the main one he attached first .... so if you don’t try you don’t know
@jasoneaster1339 Жыл бұрын
I have done this on my own personal rims and never affected them. Maby a little scratch if anything but that's on the inside nothing to worry about. Thanks for watching
@stevieprince3221 Жыл бұрын
Diesel fuel would make it easier once you get the bead broke down and a spray bottle 1bottle is equivalent to about 7/10 bottles of soap and water and a much better lubricant,can be used for removal and installation. Hope this help helps you. Wished I could find someone with your work ethic
@randallhutchcraft40393 жыл бұрын
How much for the monte carlo
@jasoneaster13394 жыл бұрын
If you dont have a rail road, anything you can use for a ramp that will hold up the weight of your vehicle will work, just drill you a 1" 1/2 hole in your ramp closer to the end so your able to adjust the chisel to the size tire your working on 👍