Hi, did you manage to solve things with Banggood? How did it go?

Same here. Also temperature measurement is offset by 10 degress and not possible to correct

Whoopem byś to ominął;)

rtc is the little battery on the mainboard it is dead that why you get that message just open the radio and replace the little lithium round battery and your all go to go.

I fixed 3 position switch locking by slightly loosing screws at the back of controller particularly behind this switch.

Nice Run! FYI your timer is couting 60 frames per second so 34 is not 0.34 miliseconds it is 34/60 frames so = 0.57

what a piece of junk, no quality control is poor, disappointed!

So cool to see you flying with someone else also flying. 👍👍

I have been working with seek pro and them show the exactly the same issue which render them useless for me. It is frustrating. Have you find a way to solve this issue?

I only fly FPV so only use 3 switches and love the V1 , my V1 only has 1 wheel the other side is an arm switch , I do take it apart and service it every so often ,,, the Gimbal tension is so perfect compared to my other radios . incredible smooth hall sensors ,, was going to upgrade but why ,,,,, been running it everyday for over a year now still works like new ,, My favorite radio ,,, I have a bunch of 1220 3v batteries thats what you replace and fix the rtc thing simple all radios do that crap

Super

I also have the 1st button issue with a brand new device. The funniest part is that the sd-card slot is just an empty void. Dropped my card inside the radio.and after opening the whole thing there is just nothing in there where the sd-card would go.. EDIT: ok i got a response that there shouldn't even be an sd-card slot, internal 512mb memory is used instead.

Is this better then the fluke micro scanner 2?

i have v1 which has none of the issue you have, i have sold it a year before and get tx16s

you have received a definitely defective product.

It's probably just urs. Send it back. Mine is actually good.

I’m looking for a solution the same dang issue. Thinking about adding a small capacitor, but I really don’t want to. My Mobula 7 doesn’t have this issue at all.

It seems Jumper hasn't fixed the most obvious issues with the v1. The 6 button switches work poorly because the rubber thingy has too short arms, which don't connect with the underlying micro switches properly. All the switches are identical and should definitely click when pressed. This can be fixed by adding a bit of glue onto the arms to make them longer. Though I haven't figured any good use for those buttons anyway. The 3-pos switches are mechanically poor, even when they work right. The down position is too close to the plastic surface, making the switch go to the middle position accidentally. They should've changed the angle of the switch a bit to make it more articulated. The USB port & the 3.5mm jack have too little clearance around them. Many connectors don't fit. At least is seems they've improved the charging, which on the v1 is nearly useless.

Thank you

do you manage to bind it?

Once again from Jumper, great product concept with poor execution. My v1 had replacement for gimbal, slider to latch button, and PDB. And now the gimbal needs replacement again. I like its form factor, but it's junk. Meanwhile Zorro is tempting but I hate to buy battery other than 18650 for remote controller, and the screen is also too big.

And that folks is why the T-lite is better :D

Are the new buttons and the big buttons on front above scroll wheel still momentary? Or are they 2 position? Momentary is so stupid!

exactly what i was looking for. thanks

I also have this v2. I haven’t checked the clock reset Both my 3 way buttons click correctly Button #1 of the 6 buttons also doesn’t click Weird! I also noticed the usb-c charge port is very picky on which wall-wart & cable. When it’s working correctly the controller will light up: green power button x:6 lights for, I assume level of charge, and a light right by the usb-c inlet.

Perhaps there is no sr1220 battery inside, it does not allow time to go astray, most of the remotes go without a battery

Were the problems solved? Are you happy with the controller now? I just ordered it today because I like the form factor and output power but I'm pretty concerned from quality control

I had a problem when trying to update edgetx, and it bricked the radio, now i can not have the internal elrs and appears multiprotocol.... And i can't find the 2.9 self build edgetx firmware. Do you have the same problem?

My V1 the usbC charging was very slow and would only charge to 8.1 to 8.2 volts. Does the V2 charge faster and will it charge to 8.4 volts?

Have gimbals improved over V1 / T-lite?

I haf the same issue with clock and date, the buttons too, mine also doenst charge

Only one interest for v2, the screen, black screen i like it. I hope v2 screen can be install to v1

Cześć planuje zakup, wyjaśniło się coś z RTC i przyciskami funkcyjnymi?

Those six buttons are enabled in the model settings and can be set to on or off when the radio is turned on.

I noticed another problem, after some time after the start of work, the app heats up and the calibration of the center of the sticks shifts. Do you have the same problem?

Have you look inside the jumper ? to solve the issues

Looks like some screws on left side is just overtightened and it’s blocking buttons and switches from normal travel.

I see no problem. A comparison may be better possible if the min/max values ​​are fixed on both devices.

co to za radio do jakich modeli pasuje ?

Qual o preço desse cachorro de mentira?

Sensacional

To ja 🙌😆🥳

Nice place, need to fly theree)

Fajnie polatane 👍

Fajnie się bawicie. Pozdro 😉

You found out that here's no such thing.👍

200e?!?!

Valor