Thank you for your comment since then I bought the Meta glasses. It really helps me do these videos. I hope you liked it and if you can leave me a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment I haven’t had that issue so I’m not sure but if I was to guess I would think it’s the board. Also, I hope you enjoyed the video and if you can leave me a thumbs up.

Thank you for your comment. I believe I use the 30 amp in-line fuse. I’m glad you liked the video and if you can leave me a thumb thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

That’s what these videos are for just take your time. Remember not to touch the bulbs with your fingers. Let me know how it goes, and if you can leave me a thumbs up.

Thank you for your comment. I don’t know what state you live in, but I live in South Florida and I have installed many dryer vents with the city doing all the inspections and I have not failed the inspection and they do not allow you to put a screen on the outside vent because all it does is block the blower The blower forces out the lint so it does not get trapped inside the vent pipe. The blower that I use states are cannot be more than 8 feet away from the dryer and no more than 15 feet at the exit point. I am curious of what blower you are using.

@@buildingwithpapa Hi. I'm a DIYer, so I appreciate any advice that is given. The directions for this Dryer Booster Fan show the secondary lint trap. The Amazon product listing states the following (See below). I would suggest placing the fan too close might create a negative effect, pulling too much heat away from the dryer. "Installation Example VK PS booster fans allow for duct runs longer than 25 ft. Install the fan at least 15 ft. from the dryer, as close to the duct termination as possible. If installed closer than 15 ft., use the VENTS DLT454 Lint Trap to prevent lint from clogging the fan. Refer to the installation manual for the correct pressure switch angle."

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

You’re the coldest we got here this year so far is 55° and it only lasts a few days so we only use about 8 inches of lime rock than the sand than the brick. Thank you for your comment and if you can leave me a thumbs up.

@ yeah will be good for a few years, you shouldn’t even use stone dust, washes away too easy

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment and if you can leave a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

Thank you

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment. I hope you enjoyed the video and if you can leave me a thumbs up.

Thank you for your comment and thank you for the thumbs up. I hope you continue watching.

Thank you for the information. I hope you enjoyed the video and if you can leave me a thumbs up.

Well, these blades are very expensive at Home Depot and I go through a lot of them the saw all used to be my favorite tool and now the multitool is my favorite tool. I know once you get the machine you’ll like it. It does work takes a little bit to get the blades exactly the way you need them, but it’s really not bad. It does save on the blades on my blades up and then do them all at one time let me know how it works for you if you see on the video I made a little pocket for the machine to sit on otherwise it moves too much and the one part where you put the blade on is a little flimsy. I think he could’ve done something better but other than that, it works really good. I’m glad you enjoyed the video and if you can leave me a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

@@buildingwithpapa I did, Papa! Thank you again : )

Thank you for your question. Yes I found that stix is a better primer. Remember, though the most important thing is the cleaning you must clean thoroughly after you put the primer on put two coats of the Benjamin Moore advanced paint. I hope this helps you and if you can leave me a thumbs up.

@@buildingwithpapa Yes, I saw you saying to wipe the degreaser off with a damp cloth. I have a habit of wiping everything down with denatured alcohol before I paint. Is there any reason denatured would be a bad idea for removing degreaser residue, does it react with thermofoil?

Thank you for your question. What cable do you have? Is it a non-tangle does it have a swivel? If so, it could be part of that but usually if it’s a non-swivel type it would not be the cable I hope this helps you and if you can leave me a thumbs up.

@@buildingwithpapa no swivel, at least I don't think it does. It looks like the exact same one you have based on when I removed the impeller cover for cleaning.

Thank you for your question. I re-watched the video twice because I didn’t remember saying that it knew it was out of the water. It doesn’t have a sensor and re-watching the video. I don’t see where I made that statement. so I don’t believe there’s anything wrong with your unit. I hope this video helped you and if you can leave me a thumbs up.

Your motor might be jammed

Thank you for your comment and if you can leave me a thumbs up.

@buildingwithpapa 👍

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your question if they are flushed with the exterior, you would still do the exact same thing if you’re going to use these panels or you can do an accordion which sets it a little bit off the face and they are better than the panel system, but they do cost more. I hope this helps you and if you can leave me a thumbs up.

Thank you for your comment and no, I don’t mind you asking in the description. There should be a link to purchase the switch. I got it on Amazon Amazon. I hope this helps you and if you can leave me a thumbs up.

@@buildingwithpapa already did and subscribed. 👍

Thank you for your comment. What year is your Escalade?

Thank you for your question. I used contact cement. It worked really well. I hope this helps you and if you can leave me a thumbs up.

Thank you for your comment. I hope that once you watch this video you were able to put it back so you can leave me a thumbs up. It really really helps the channel.

Thank you for your comment and if you can leave me a thumbs up

Thank you for your comment. I didn’t have a microphone back then I made a couple more videos on how to do this process that has better volume. I hope the video helped you and if you can leave me a thumbs up.

Thank you for your comment. If you would watch the video all the way through I put silicone on all the joints and the screws. It works very well. I hope you enjoyed the video and if you can leave a thumbs up.

Thank you for your comment. I did use silicone on all the joints and on the screws. I hope you enjoyed the video and if you can leave me a thumbs up.

Thank you for your comment. I’m glad you enjoyed the video and if you can leave me a thumbs up.

Thank you for letting me know. I will contact them and find out what the issue is.

Thank you for your question. It could be the amplifier I was unsure of mine. My speakers would go in and out. They would work sometimes and not others. They would make some static noise and I found out it was the amplifier you need to remove the amplifier. follow the video numbers on the amplifier I showed in the video, and then you can one. I think I got mine on eBay and follow the instructions. There’s one screw that’s a little tough to get to but you will be happy once it’s done. I hope this helps you and if you can leave me a thumbs up.

Thanks so much I built up the confidence to tackle the radio no sound and you were 100% correct. The 2 cylinder parts that's wrapped in a coil type style has burnt up 😞. All I need to do is find myself a replacement 👍🏾

Thank you for your question. That junction box is a transformer if it’s heating up then it’s possibly getting ready to go bad if you have swish ball colors switch it to a lesser one and see if it stabilizes. If not, I would change it out. I hope this helps you and if you can leave me a thumbs up.

No, I haven’t had any issues with it. I hope this has helped you and if you can leave me a thumbs up.

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment. I’m 68. It’s really not that bad to get in there. I’m glad this video helped you and if you can leave me a thumbs up it really helps the channel.

Thank you for your comment and if you can leave me a thumbs up.

Thank you for your comment, but I’m not inside my house. I am outside on the porch. I have stayed away from it. I’m not concerned about it. I have worked with these things many many times. Thank you for your concern and I hope this video helped you if you can leave me a thumbs up.

Thank you for your comment and yes, I do have a tripod now and also even the metaclasses it is helped extremely. I hope this video helped you and if you can leave me a thumbs up.

I’m sorry to hear you’re having some difficulty with yours. I don’t know the brand of saw that you have you should be able to order that plastic piece that broke. I hope you’re able to locate that piece. Let me know how it goes.

@@buildingwithpapa mine was a Ridgid as well. The laser is discontinued. Looks just like your laser but a 3 piece assy. The top piece is in 2 pieces. I'm going to try and drill it out and re-tap it