where did you get that conversion chart from? Ive been looking but cant find it on the net mr factotum uses one but the image isnt clear enough to use
@iankoegelenberg46828 ай бұрын
Well done, thanks for the video.
@RustyInventions-wz6ir10 ай бұрын
Very nice engine
@tomgullan356511 ай бұрын
Yes, this is my first video. It's a very easy process, good luck.
@rikabob Жыл бұрын
Thank you for showing how to do this. It is the first video I have seen where someone changes these gears to cut metric. I have the gears but never used them. Now you showed how easy it is, I will try to cut 2.5 and 3.5 mm pitches.
@rcurry8531 Жыл бұрын
Very nice job. The only thing I got built Is my gas tanks. I made two. Thank you
@gwheyduke Жыл бұрын
Good video. Sounds and runs great. Beautiful machine work.
@gwheyduke Жыл бұрын
Nice engine. I met Ham Upshur at the Cabin Fever Model Engineering Expo when it was held in York Pa.
@MadeInGreatBritain Жыл бұрын
Very very nicely done
@andrewdolinskiatcarpathian2 жыл бұрын
You did well to find a windscreen wiper motor without run out problems. Neat solution 👏👏😀👍
@jamesthemotormaniac28073 жыл бұрын
What kind of ignition system did you use?
@jessestrum3 жыл бұрын
nice one tom
@johnmcdyer72973 жыл бұрын
Where’s the renewal
@EvoKeremidarov3 жыл бұрын
Did you scrape the bearing?
@mikew32325 жыл бұрын
Superb.. I have the same milling Machine I'd like to fit a Power Feed to. Do you have a circuit diagram for the electronics you used?
@tomgullan35654 жыл бұрын
Sorry Mike, I’ve just come across your question. The answer is yes I do. If you still want it, please let me know.
@baljinderkainth98535 жыл бұрын
V v nice
@stuartsurkitt25856 жыл бұрын
is that a wiper motor? if so, great idea.
@tomgullan35656 жыл бұрын
Stuart, yes it is. There's another movie on my channel with the finished item. It no Ideal but it works fine.
@stuartsurkitt25856 жыл бұрын
cheers Tom .
@tomgullan35656 жыл бұрын
natalefr Natale NOVELLO, drop me am email at [email protected] and I’ll talk you through my build and some photos if you like.
@natalefr6 жыл бұрын
Hi Tom what is your electronic ignition ?
@natalefr6 жыл бұрын
GOOD and cheap idea :-)
@natalefr6 жыл бұрын
Nice job :-) One question... I Want build same engine and my question is: Your top plate is in aluminium ? If yes how tickness is it ? Regards from France
@tomgullan35656 жыл бұрын
This is a four stroke petrol engine... because there is no sump, I add a very small amount of 2 Stroke oil to the fuel. I used Viton O rings instead of cast iron.
@natalefr6 жыл бұрын
Hi nice engine your fuel is what ? This engine is ith or without rings ? Regards from France
@gordonmuir50516 жыл бұрын
Verry good tom, works perfectly.
@tomgullan35656 жыл бұрын
The same again but horizontal and it will be converted to gas. It will require modifications but it is doable.