Should have left the nails and sleeves in place as well with them

If the drip edge is brown with the drip white paint on it. Then what is the apron that is supposed to be on the fasica board. The drip edge I thought was suppose to be on the edge of the house that has no gutter. Am I wrong?

The drip edge is NOT for keeping the water from going into the facia wood. It's to cause water to DRIP off of it into the gutter without adhering to it and causing it to run against the facia at all. If you make your kitchen faucet produce a thin stream and touch it, it will curl backward, it's that affect a drip edge is meant to destroy.

This is exactly my scenario. They installed these hidden hangers on my roof that already had those same drip edge. Now I have leaks between the gutter and the fascia in a lot of places.

Thanks! I needed that info. My 330T is putting out too much oil and making a mess when cutting.

for when the fascia is capped with metal

Your one of "those guys"

Not sure what color of load was used but try Green load (lowest amount of power load) if still to much force drill and tapcon lag screw.

What kind of dog?

Framing ?

thank you algorithm

YUM!!!!

Thanks Glenn

Interesting stuff

I love the security system on the hose

Cool Trick!

MORE dog

U could have put the rain gutter below the drip edge. Then you could have used a piece of straight metal flashing as an extension. Put it under the drip edge / and over the rain gutter. Ur drip edge looks short / the capillary action may wick water into your house. Perhaps using a little sealer under the drip edge would make it 100. But good u got it tucked.

More of this dog pls, shes so cute!

Shouldn't use those hangers!

Drip edge and Gutter Apron are 2 different materials for 2 different locations. Drip edge is for Gable/rake sides of roofs and Gutter Apron is for the aeve/gutter sides. Gutter Apron runs down and into the gutters.

drip edge needs bent out more . I just decided since Iwas putting on a new roof to get 6 inch gutters and they are great . Drip edge is bent out and my house is 100 feet long . Ice and water shield on whole roof and new shingles and gutters cost me 11 thousand dollars . Plus all new custom bent drip edge , not the cheap garbage you buy in lowes or home depot that has almost no drop and no decent drip edge

Not only do you not know how to install a gutter properly, why would you ever lean a ladder against a gutter? SMH

Whatever you do, don't silicone that top! I've seen it many times. Personally id get it up under that drip edge but you could just flash it as well. I use that as a last resort if the level brings the gutter down below it.

well it’s called a concrete nail. i wonder what material you’re supposed to use em on?

Had the same issue with my 2011 nv200. Sprayed CRC engine start into the air filter compartment for 3 secs and start but in a weeks time it does it again

Had the same issue with my 2011 nv200. Sprayed CRC engine start into the air filter compartment for 3 secs and start but in a weeks time it does it again

Both hangers represented here are junk , one weak as hell but both carry the same liability. Allow water to wick back towards the fascia, speed hangers are junk carry screws in your bags like a man. Remember to your penetration should always be as high as possible without missing the back of the gutter. This will minimize any moisture getting to the fascia, if you live in a cold freezing climate align drive longer screws that will allow penetration into the rafters.

Thank you. I was wondering why my gutters were in such bad shape. I pick up the brackets at Lowes but you are correct its the same brackets at Home Depot.

Working on gutters and drip edges right now. I appreciate the advice

I honestly think this is a good idea. I’ve had a couple gutter I’ve installed myself and knowing the fact that one side must be higher in order to get the right slope, u deal with this issue where the edging is. I’ve tried tucking the screw under the edging but it can only go up so high . Thumbs up bro . Question do u put those hangers at every 16” ? Or even when there is a fascia is there a certain distance u should have them @??

The AC Guru was counting on positive thinking to hold those pipe together...maybe he got sad...

im not tyler

Excellent

So the hangers should be installed under the drip edge? I looked at how my neighbors gutters are installed and they screwed the hangers right through the drip edge. Im not sure if that is right or wrong, but he had a gutter install service install his.

You have exposed fascia wood, and incorrectly installed gutter hangers. Water will get into those screws and rot the wood. Just pull the drip edge away from the fascia and put the gutter hangers under it. That's why the hangers have that gap there towards the back. Admittedly all the gutters on my house are like this, I've made some repairs and while I was there corrected the gutter hangers. But honestly they've been like that for probably at least 20 years, so I'm looking at major repairs to the fascia boards. I'm no expert, but the number one rule in roofing is to shed water and protect fasteners. I think the reality is that the drip edge should be installed with 1/2" or better space between it and the fascia. That would allow room under it for gutter hardware and would prevent any water wicking up to the fascia.

Menards still sells the good ones.

bruh

Mine don't bend in, but they do bend down and let the gutter escape... Except mine are 30 years old maybe it's just an older style? I agree the reviews for the amerimax ones are lackluster compared to others...

Problem is that i have seen 90 percent of the drip edge is installed wrong, it should be off the fascia board 1/4' or about your pinky finger width off the fascia. This way you can install the gutters correctly using those hangers

Those electric vehicles have so many problems

STOP CALLING and Blaming it on CON-VID ... It was and is a "PLANNED ECONOMIC RESET" words from James Bullard in March 2020 President of The Federal Reserve Bank (Private not owned by the USA Government) for those who didn't know that. aka...The Greatest Theft Of Wealth In The History Of Man.

We always used a ladder stand-off like a professional would.

They are supposed to clip over the gutter, not be screwed through the drip edge.

Home Depot sells a lot of inferior products.

The only bad thing here is you and that garbage rigid brand

You possibly used the wrong charge, sir. Plus that doesn’t look like inch and a half block.

good video glenn.

I has some morons do my gutters, I hate moron gutters. I had to tear mine down and put them back up to get the back of the gutter behind the drip edge.

*PromoSM*