Пікірлер
@kylemclaughlin1578 13 күн бұрын
I found your Channel in regards to the China diesel engine you put on a log splitter. I got the same China motor and I am looking to put it on a huskee 20t splitter from tractor supply. I also have a 21 Honda rally. I run the Dunlop d606 rear and mt21 pirelli front, great mostly off road riding tire combo for the California desert and mountains where I live 😊
@deankurkov2703 20 күн бұрын
Trailer sticker has the word "Maintenance" spelled incorrectly (maintanence is incorrect)
@dangareau 21 күн бұрын
You should have called this video "Buy new tires instead of lowering pressure" cause the stock IRC tires need to be lowered to 17psi for offroad in NJ Pine Barrens and most of the east coast (not just Florida) cause like you mentioned sand. Now granted my skills have waned a bit but 22psi on my 2023 Rally is for highway use only, less I want to show off how bad I've gotten. I was gonna ask about the mt21/d606 combo but it sounds like your terrain couldn't be more different than mine. I might as well live in Florida terrain wise it's identical.
@ThriftyGarage Ай бұрын
I bought 2 tanks a few years ago and one of my tanks leaks pretty substantially now. Can you still say you haven't had any leaks?
@toddcarpenter4237 Ай бұрын
Yeah , twenty eleven four fifty has that same issue
@son-of-a-gun 2 ай бұрын
I own a small Chinese diesel generator. I put it in a small shed made of concrete blocks for silencing. Starting the thing is not a problem at all even after a very long time . I put some lube oil on the cylinder and start it using the decompression device. It never let me down, but it smokes in the very beginning, later it's running smoke-free and smooth. Hurray for small chinese diesels and generators. Some people believe chinese products are crap... They are not!! You pay what you get
@MrFictionfactory 2 ай бұрын
Does this booklet also contain the valve lash clearance? I really need it for the service on my engine, I can't find any information or tips about it anywhere on the internet. Thank you in advance.
@sjf67gto 2 ай бұрын
Did you tear this down without a manual ?
@higordaniel7793 2 ай бұрын
Thank you very much for your video series, it's invaluable content! You were the only one who I could find doing it, but not only that: you teached very well! Thank you!
@joenuclear4445 2 ай бұрын
Thanks, Travis I eenjoyed the vido!
@hawaiiantimes7702 2 ай бұрын
👍🏼👍🏼👍🏼👍🏼
@joenuclear4445 2 ай бұрын
Nice! Informative and well "filmed". Maybe in the future you can discuss the bike setup layout your gear on a tarp.
@jydog57 2 ай бұрын
Did you find a replacement piston or is this a different engine?
@user-tj3sy5ug8k 4 ай бұрын
have you thought about converting to an electric start
@tigerelectronics5966 4 ай бұрын
Im really surprised by the quality of the parts. Considering this engine only costs 200 bucks... This is pretty good, I have to say. Ive got one of these engines myself, using it in a low rpm generator setup, considering that I only run it at lower RPMs (below 2000), I think it will last just as long as any other engine would!
@zapmaster207 4 ай бұрын
Nice hat thank you for your service. Good BIW ship.
@mossycreekvids 3 ай бұрын
I was glad to serve, but that was early 90's. The Carney DDG64 is the ship my Daughter is on. She just got back to states after 7.5 months in Red sea area. Proud Dad!
@BobBlu-wn9cp 4 ай бұрын
I just got one of these about 2 weeks ago from Amazon. I went thru the first time start up and it went well. It started 3 times in a 2 hour time frame. A week later I tried to start it and it would not start. In fact diesel fuel started to spit out thru the air filter. What would cause this? I messaged the seller and he suggested I clear out the air filter and fuel line with carb cleaner to dry it out and start it again. Same thing happened, fuel spitting out thru the air intake. Second message from the seller was to take it for repair. They would pay up to $30. Any ideas? It's still under the 30 day return policy
@mossycreekvids 3 ай бұрын
Have you figured it out yet.
@nellhikk8542 4 ай бұрын
Made from Chinese monkey metal
@nathanmandeville3205 4 ай бұрын
So do you order your parts from wsepo? If so who did you talk to and how was the experience? I’m trying to decide on ordering the new model of that engine
@mossycreekvids 3 ай бұрын
All email communications, sent exactly what I needed.
@Krazycat321 4 ай бұрын
Found the Problem! It says it right on the side….. “ made in China”
@fixitandfloatit5915 4 ай бұрын
wd40 has worked great . my original 196 must be close to 100 hours
@chuckvoss9344 4 ай бұрын
Very interesting how well the hot water worked. Thanks for sharing.
@phopnick 4 ай бұрын
I am looking for the Torque Specs for the Connecting Rod, FlyWheel, and Head Bolts. Would you happen to know them or point me somewhere to find them. THANK YOU!
@noyopacific 5 ай бұрын
I appreciate people who aren't the least bit bashful about accepting responsibility when stuff happen. I get tired of people who's first reaction is to start blaming others. You are a good guy in my book. Best wishes, good luck and thanks for the video !!!
@Lawnmowerman02346 5 ай бұрын
I agree that the starting fluid was the final straw but the discoloration suggests a casting flaw . If it was a one time start on starting fluid I don't believe you'd get discoloration , that's usually from previous run time . If it was fresh carbon the starting fluid would wash it out and be shiny . Ive cast Aluminum before and it can be hard to find flaws until machining and when you have a machine pumping them out by the thousands they only inspect maybe one in a hundred .
@tigerelectronics5966 5 ай бұрын
I put one on a generator, mine started right up without any hesitation at all in -10°C! I was seriously impressed! I didn't do any preheating or anything at all, just a normal start!
@scramjet4610 5 ай бұрын
How do you check the air filter? You just glossed right over that point. There is no wing nut holding it down as is usually done. There are arrows pointing both clockwise and counterclockwise on the air filter lid, but it will not turn. How do you get the top off that plastic air filter housing? Isn't it important to have a look at the air filter element?
@mossycreekvids 5 ай бұрын
Mine would turn and lift off, wingnut on filter under filter cap
@handheldgarage3297 5 ай бұрын
Can you post a link to the tachometer/ hour meter on there. The tach/hour meters i u=install on my small gas engines run off of the spark plug wire
@mossycreekvids 5 ай бұрын
amzn.to/3vEe8aQ
@mossycreekvids 5 ай бұрын
Here is the link, I have tried cheaper vibration hour meters and it was JUNK. The vibration on hour meters do not measure RPM only time
@jimalton1564 5 ай бұрын
Fantastic ride! I have done several Iron Butt rides (SS1Ks, at least 4 BBGs, and two SS2K golds) and enjoy giving tips to newer long distance riders to help them streamline their rides and make them a bit easier. However I see nothing I can offer you, you did great with the bike and conditions you had to work with. Other than adding lights for night time riding, which you talked about, there isn't really anything I would do differently. There is no getting around a small bike taking a bit longer than larger bikes- you have lower speeds, no wind protection, and limited electrical power for luxuries like heated clothing. Well done.
@mossycreekvids 5 ай бұрын
Thanks it was a good ride.
@billsimpson604 5 ай бұрын
Buy a new gasoline engine and change the oil a LOT & you will probably get between 1,500 & 2,000 running hours out of it before it dies. The most important thing with a new small engine is to change the oil after an hour of break in. Watch all the metal that comes out. You can't change the oil too often on an engine with no oil filter. If the metal was no big deal they wouldn't put oil filters on cars & trucks.
@doorbash5680 5 ай бұрын
I put a 10 horsepower Chinese diesel with centrifugal clutch on my old Honda 125 drove it for 20,000 plus miles going back and forth to work in the spring and summer for 3 years. Price of fuel now I might have to dig it out of the shed and get it back on the road.
@Bullworm562 5 ай бұрын
What thread size/length were the mounting bolts for the pump? Metric I'm assuming.
@offgridmangogrower 5 ай бұрын
maybe 2 hours on it….
@offgridmangogrower 5 ай бұрын
Mine broke in half
@mossycreekvids 5 ай бұрын
The piston?
@AJRestoration 5 ай бұрын
Starting fluid/ether tends to break diesel pistons in this way.
@Cletrac305 5 ай бұрын
Roll up a rag, remove the air cleaner and spray a little ether on the end of the rag then hold it next to the intake. No liquid can get into the motor. I have done this for years. It also lets you run it for a while with the vapor assisting it. You can control it by pulling the rag away. Also, an electric heat gun works much better than a propane torch in the intake as it doesn't burn up the oxygen.
@scramjet4610 5 ай бұрын
Where is the fuel switch on this? Its says to open the fuel switch before running, but I can't find a fuel switch anywhere.
@mossycreekvids 5 ай бұрын
Mine has a red knob on side of engines loosen knob and.it will allow throttle to move by moving red knob. Lock into engine speed you desire. If loose it returns to 0 fuel injected and engine stops.
@west_adv 5 ай бұрын
Like you said in the end - lower pressure makes sense in sand and in deep mud. Your terrain looks rather dry and rocky, this is why 22psi is good for you, while I prefer 15 to avoid being stuck in some muddy pit. Cheers from Europe. Very informative and interesting test!
@michaelhulas9801 5 ай бұрын
Shit man, that was fantastic. I’m surprised you still have mirrors left on that bike, Ha. Really impressive video, thanks for making this.
@mossycreekvids 5 ай бұрын
Thanks, That was a fun little rip. This bike will very seldom see that type of riding I am usually a very laid back dual sport rider. It is nice to know the bike is set up properly now if I have the need or want to ride it fairly aggressive. Even with my tank bag, front saddle bags and rear rack less luggage loaded with tools, tube, compressor, riding gear insulation and other day ride needs the bike handles very well. I am 6ft weigh in at 240 ish geared. Before doing the suspension the sag was waaaaaaay off and extremely soft. It pushed so bad in the front I would have struggled going 1/2 that pace and would have most likely lost my mirrors. LOL
@Chris-yy5pj 5 ай бұрын
What tires are on the rear of that rally?
@mossycreekvids 5 ай бұрын
D606 on ride portion, irc stock on impact test
@babar69110 5 ай бұрын
i run a 390 beta RR at 0.5 bars front and 0.3 rear. You just need two rim locks on each wheel, an ordinary tube and spray silicone on tube. Period. 5 years without ANY pinch... Of course some dents on rims, but i don't care. Survived mid center Albania tracks where you just dream to have even only 50 m to ride without a stone :) update... A Pro told me once to more inflate front, whatever the terrain, because the plush of lo pressure tire would interfere with suspension work... So sometimes I increase to 0.7 to 0.8 front and yes on rather small rocky tracks forks work better
@mossycreekvids 5 ай бұрын
That's impressive
@bajageorgia6933 5 ай бұрын
Good info. Did you have it loaded with your typical gear? Were the bags close to the actual weight they’d be if you were on a multi day ride?
@mossycreekvids 5 ай бұрын
I had it loaded with my typical day ride gear for this time of year. Quart extra water, top and bottom riding gear insulation, cold weather gloves, tools, extra tube, compressor, lite hiking tarp to cover bike and or self if I get in a bind. Sawyer squeeze kit. Heat controller for electric gloves and first aid kit. That stays pretty much all the time on bike till it gets consistently warmer. This time of year I need my duffle on back for multi day camping. But I don't pack really lite. I plan on doing a video on my packout for day riding and camping in the not too distant future. I could multi day camp without duffle on back in summer as long as I have known water sources along the way so I don't have to pack water for cooking or can eat out along ride.
@mossycreekvids 5 ай бұрын
I also tend to ride solo unfortunately, this prevents sharing of equipment and gear which helps a ton on keeping down what needs to go.
@rickyzoom8059 5 ай бұрын
Great video. Found yourvideo very helpful for my CRF 300L Rally. Applies worldwide including our Australian trails.
@mossycreekvids 5 ай бұрын
Glad it helped!
@Enviromentalist1952 5 ай бұрын
I was pleasantly surprised that your route cane down here in piney country. (I live in Smackover on hwy 7.) Well done! I think it was extraordinary that you did the ride this time of year and gave up the extra hours of daylight. Good Riding to You!
@mossycreekvids 5 ай бұрын
Thanks, I have found very few places I don't enjoy riding. I had 2 places on the trip that I really was tempted to stop and camp. Not because I was ready to stop riding but because I saw some cool spots to camp! The spots were in the souther piney part, and the other was a ridiculously tempting levy road in Stuttgart. Lol
@HappyHands. 5 ай бұрын
definitely a casting/metal quality fail
@stanleybest8833 5 ай бұрын
I turned down the limiting screw because I just don't want my motor turning too fast.
@logarithmic_simplicity 5 ай бұрын
How was the stock seat? Is it worth upgrading to a SeatConcepts one?
@mossycreekvids 5 ай бұрын
Everyone is so different. This is the most comfortable seat stock I have ever had. Including Aftica Twin, GL1500 and V-strom 650. Others hate it. Worth giving it a try.
@illernpiller 5 ай бұрын
Oh do you have the link to the tach you have on it? I need one for the diesel i'm buying.
@mossycreekvids 5 ай бұрын
amzn.to/3vEe8aQ
@MmmHuggles 5 ай бұрын
You are the most organized person I've ever seen tearing down an engine. Most people are a lot sloppier lol.
@jimb032 5 ай бұрын
Yea, i dont think you blew it up...that would have happened anyway sooner or later. You just accelerated it. I dpubt that would jave made it to 100 hours. Chinese just are not good at casting metal.