No - the course that I've uploaded here is like a draft, unfinished and not complete - this video is the updated full course - you can find the link below

While rendering, at least only in the process of rendering I observe this - the laptop begins to heat up and the sounds inside sound like a plane that's about to take flight - I guess it's increasing at that time the clockspeed - I didn't test exactly that - I believe it's 5.8 GHz - you see the main idea it's that I don't want to link 100% to technical numbers, I wanted to show from an intuitive pesrsective of how it feels the work rather that sticking to some +/- seconds of it's activity. I guess that it has to be at least close to that number Intel writes on the processor - anyway if it gives around 30-40 min / render view - it's ok for me 😉 - previously I was getting a view in 1.5 - 2 hours

Actually I was looking for PC - but the idea is that it's almost twice as this laptop ((( - it's my next target !!! For now I can say it's doing what it has to do - by the way I think they are at least for 5 years working, hope it lives at least 5 )))

@@interiordesign3dsmax well u have the best designed laptop. I mean inside and then out. But I see super io bios chips die right after the warranty has passed, that or it will be dead mosfet on mono charging port. So that is my advice.. Do not take the charger out of the port bc they are designed to fail and u can do that bc u want to use the laptop as pc so congratulations on the new beast and have fun using it ☝ ☝

@@ChudGippity ))) I will write u back in 2 years - we'll check the health of this beast ))) - thx man !

O it will work for 3 yrs for sure dont worry it is a Strix@@interiordesign3dsmax

@@ChudGippity Hope it does - he got a lot of work ) 👍

thanks

activate it in Vray frame buffer - watch the video - you will need a realistic 3d model if you want to see a realistic effect

@@interiordesign3dsmax thanks bro, I have a problem when taking the photo in vray the jpg appears white

@@antonioch1135 all the images appear white? or just one in particular? your vray is installed properly? you use vray frame buffer? your alpha chanel is turned on?

@@interiordesign3dsmax Yes I use the Vray Fram Buffer, and when I put save history, the image appears with black shadows

@@antonioch1135 I need to see the image - it's hard to tell - can you record a small video and share a link?

final render it's a mix of layers - and there are layers that are activated after the entire render is ready - they use the info/data that was calculated and after that apply a smaller algorithm to calculate additional features you see in Vray (for example - I'm using only Vray) - I'm not sure about clouds - I work only with interiors - my tasks are linked to interior design projects mainly - but - if you don't see it in interactive render - perhaps that layer is only activated after full render calculation Do you use new Vray 6 clouds? I watched a bit how they work - but it's not my direction - I dig in depth in my main interior direction, I don't have time now to be a learner, except for some small features that can increase my image level ... hope it was useful )

@@interiordesign3dsmax thank you for replying on such a short notice.. to be honest the main problem is with the sun.. I get the bloom/glare in the process of IPR, but can't get it in the end of an HQ render, doesn't matter if it's for a minute or for many hours, the lens effects is just greyed out and I can't even enable it. also yes I'm working with volumetric clouds which are a part of an environmental project I've been working on lately 🙂, but that's just fine, my concern is the glare

@@davidchalabian469 success )

hello - no problem - you can use it )

Only Brute force (use it for renders - gives a lot better results) - it is based on calculating the light bounce points - the algorithm of Irradiance map it's a bit different - still, keep in mind - it won't help too much if your lights are out of balance - try interactive render and light lister before your final render

Thanks for answer. Brute Force better but longer, I choose IR for my project deadline. I just play with my setting and now it work with Irradiance map already.

@@vjaygroup8759 I use only Brute force - you will deal in quality favour vs speed with time if you seek to grow - anyway, glad it was useful - success !!!

ok

@@interiordesign3dsmax I am waiting for the AutoCAD files

@@hazratumar1824 write your e-mail - I will send you the plan - although there are the dimensions at the start of the video

thanks - this was a "compressed" fast version of the process - I will try to add more details in future videos

Glad you liked it

thanks