Bleach works

How do you get the rope back out

Vielen vielen Dank.

THANK YOU SO MUCH ITS 3:55 am and within seconds im not itching anymore, seriously dude thank you so friggin much I’ve been DYING, baking soda for the win!

Great timing! I bought this off Amazon a few days ago and haven't gotten around to installing it yet. Thanks for the video, I'm looking forward to getting mine installed

They list this 24000 btu as having the cooling area of 1500 square feet. Do you think that is accurate? If not, what do you think the actual cooling area is?

Did this come with freon or did you have to add freon yourself?

If you value your hand, don't use gloves when using drill press

I had the exact same issue, and I followed the info here and replaced the capacitor, and the issue is fixed. Thanks for the post.

Why don’t you show the set up?

Your using it wrong. You work a mini tiller backwards.

Thanks a lot. Wish I would read this before buying a new battery. And just remark - I measured capacitor after removing it - it was aprox. 110uF. This leads to 3 possible reasons for this problem: 1. designer mistake (usually designer must put twice higher value than required to compensate aging); 2. Capacitor parameters doesn't correspond to marking; 3. Capacitor temperature environment is too high (higher most of the time than normal which is supposed to be 25C). So, when you buy replacement buy the one with temperature grade 105C, not the one for 85C. And if you find higher capacity in same form factor - better use it (of course voltage must be 35V+)

This was a pain to do but i did it. Tipped it like you did but onto a car seat which helped. Deck came off like a champ but was a pain to get back on. PTO clutch nut was a bit but a hammer on a socket wrench took care of it. Engine pulley luckily slid right down belt went on easy but the idler spring fought me but i got it. Then the deck was a pain to get back on but i eventually got it. Had to attach the back j hooks first then use the triangle piece of metal on the front to tighten it up then i needed a ratchet strap to get the belt back on the idler wheel on the deck but i got it and i now have a working mower. I cleaned out the deck all the grass and fluid filmed the deck and greased the blade bearings and everything works.

Hi. I just wanted to Thank-you for posting the capacitor problem in the base charger! I have a Roomba 630 that was showing ERR5 also and after replacing the Cap it's alive again!

Kodiak how do figure “the pull cord go through the metal bar” when there is no metal bar for the pull cord to go through. At least on the MC33 model shown in the video.

Your video helped a lot! Watched a video where the guy loosened his engine bolts so he could get the belt on the front pulley, sure glad I watched yours and found out I could just slide the pulley down a little. 👍🏼

Hopefully, it's reliable. If this internet service doesn't work 99% of the time, I would be pissed.

Well done.

Video no good

Thanks, I thought that was how you wired it, what was throwing me off was L2 was a blue wire and that is usually a neutral wire, but both L1& L2 are hot wires, thanks for making the video, you're the only help I've found!

I'm having trouble seeing where you hooked the 220 wires from the breaker box to the outside unit, do you hook the 2 hot wires to L1 & L2 and leave the "S" wire blank? I see where ground goes, Thanks Ira

ANOTHER one who DON'T READ assembly instructions. The pull cord go THROUGH the metal bar, per assembly instructions.😆

I love my century welder I have same model and vintage...

So now you have a cat that goes outside, but brings in fleas and ticks into your home. Just great

Made one out of two wheel barrow wheels about 4 years ago.....but i dont get it, you said you didnt have a few days to wait on the well guy but spent about 4 days building the thing, unless you change clothes 2-3 times a day? If the emergency was really that bad, why not three wood poles some rope and a pulley to make a tripod for the emergency....nice roller for the poly pipe though.

Hey John, I have the same tractor. My tractor will not start. The oil and battery light come on but the glow plug light doesn’t. I replaced the battery because it was 11 years old. Still won’t start, won’t even crank. Have you had issues like this with yours?

Simple and effective. I think I may try this myself.

If it's jetted for natural gas, do I have to reject it for propane?

That weed killer is toxic. FYI

One needs to remember which treated bushes were poison oak. The dead plants still have the active ingredient, urushiol, for a long time afterwards.

Hi, How did you know it was the capacitor and not the battery itself? Thank you.

What headlights did you use?

Unfortunately these are not available on Indians Amazon 🙄😖😫

That looks like that was a big job.I hope to buy a tractor like that one day

Thanks for sharing.😊

I think they are a great little saw, I purchased one for brushing some overgrown fields. I put a 18" Laser bar & chain on it just for more reach and replaced the standard clutch with a cartridge type to help keep the chain from being thrown by grass and brush. I love the saw, it starts so easy and runs great.

I tried to give you 10 thumbs up,but it would not let me,THANK'S. You saved me a lot of grief!

Thank you very much for your help.

Where’d you get the lights? I cant find the LED headlights anywhere. I don’t need the whole black plastic part. Mines good but I can’t find it anywhere

Thank you sooooo much!!!

Why has there not been some type of class action lawsuit against cub cadet with these mowers? This has been going on for years and they are still making junk. I for one will never own another cub cadet of any shape or form. JUNK PURE JUNK.

How long did it take to get this all hooked up?

Will the seeds from an October Glory produce an October Glory or just a red maple?

It's cotter pin and impact

We are considering this tree. How messy are they during the year. I know all trees are but how would you rate this one?

Cheers John 🙂

Thank you!!!

You should have bought the AGKNX Model 400 auger. They are made for these sub compact models.

Should you grease the needle bearing before you reassemble?

They are definitely related to autumn blaze. Magnificent color