Thank you... work fine..🎉😮

Hello! I know this video is years old but I recently had to change out some coil packs and ran into the issue with the connecters. You saved me time and money. Thank you very much. I followed hours instructions and it worked. ❤

Thank god i found your video ! Thanks so much if its higlithed neans is not functioning well right ?

Hi! Can a loose connector cause misfire even if it does not come completely off?

Good information, thanks

Worked like a charm. Thank you sir, super like !

Great video especially the recalibration of blend doors ..

My engine us just like yours, where does the rpm wire connect to? I took the harness off and now i can't get the rpm to work, thank

Great help,and camera work!

Ford parts are so chinsy. Ridiculous!

Is it possible to utilize the power balance test with Forscan? I cant seem to find any information on it.

Got it! Saved me $$ and accomplished it myself.

Big thanks! I too seen your vid before I tackled number 8...I did have the reducers and worked perfectly....cant thank you enough.

For rx8s you do this then shut the key off and then start it untill it runs it wont go away

Great video!! Saved me much @$$ pain, scraped knuckles, bruised arms, and more. A quick trip to Napa for a $5.00 1/2" (F) to 3/8" (M) socket adapter, and was able to remove and replace #8 spark plug in 10 min. Would love to buy you a beer, my friend!

Terrible video not showing how to dismantle center console or putting in new act 👎👎👎👎👎👎👎👎👎

OMG... you are So Good... it Works

❤

Bro you don't know how much you just helped me out

Do you have a video splicing it back in the harness

Thanks

Mine isn't going off. I knew it was too good to be true 😂 lol

Didn't work

Bought new cam positioning sensor pig tail, wires are white an black ,don't knowitch goes to mine,orange, an orange with Grey line

Cool,can u do same with cam positioning sensor

You just saved me so much stress, headaches and aggravation. I was getting cylinder 2 & cylinder 4 misfire. Haven't had the truck long, but figured the coils were bad with the truck having 140k on it. I replaced all 8 and drove for a short while and felt the hesitation come back. Check engine light began blinking and the engine power was down to where my a/c quit and power steering was cutting out. I got 3 of these clips that broke as yours did. I pushed them back on as best I could and figured it would be ok, but obviously not. Thankfully I found this video and plan to hit the junk yard on my way home today. There is a few of these in the yard there. Hopefully I can find some that are still decent enough. No way was I going to cut and splice, but figured I would have to replace the whole harness and or take it to the shop. I am so relieved that I can fix this myself. I am good with cars and almost always repair things myself, but I do not like messing with electrical because things are so finicky. Thanks again. I feel so lucky to have found a video that was the exact problem and solution in 1 short video.

Thank you so much. Just had this after replacing the battery. I thought something else was wrong.

Legend thank you so much❤

Took you 10 minutes just to get the second one off...

Maybe been asked before but what OBD reader are you suing? Great video

Why didn't you show how you got the house off in the back??

wow, the only video I have found on KZbin. My problem is that I'm not hearing any clicking noise. I didn't know that it was possible to recalibrate the blend doors so I am going to try that this afternoon before I go any further. Thank you.

This saved my life. Thanks so much!

thank you so much bro

That one behind the radio is so easy. Took me 20 minutes start to finish. Charged the customer $50 labor.

Straight to the point no bullshiet thank you

De pin kit off Amazon is definitely a must have.

TURN ONIGNITION !!!!

Thank you very much. You helped me repair a broken trim center in a boat that I’m installing a trim gauge in that never had one in it before you save me a lot of work and money.

THANK YOU! saved me a trip to a mechanic. Guess it's all to do with the electric steering needing to be repositioned/reset.

Just break the tail off the spark plug, simple as that.

Does the ECU on a 1998 Ford Explorer record misfire data for each cylinder or is this car too old for that? I can find total number of misfires on a bidirectional scanner but no cylinder number record. And I've looked in mode 6 but test 53n the misfire one, isn't available. Same issue when using a computer-based generic OBDII scanner.

My wire broke. How do I fix that? Thnx

Great video

Thanks for the video I have been wrestling with the idea of pushing the wires through the hole without removing the whole outdrive. 😮. This is a much better option...😊

Good video still helps me in 2024 tanks

After all this year, yes, it is very useful, thanks

I have 2005 f150 leriet with center console would it be that easy

My f150 is the only vehicle I’ve had that I’ve literally taken the entire interior apart over the years fixing various issues 😩

Wow, it worked like a charm