Great Vid here, helped me a lot in changing the servo, really thought you have to disassemble the whole chassis..thumbs up vid

Hello ! my problem is the throttle neutral. impossible to adjust... is this the way to trim it ? (I have to push a little bit the trigger to be at the neutral, but it i don't touch the trigger, le motor is running forward...). If someone have an idea... thanks !

Hello, I have a SLT2 (with an Arrma Gorgon) and i change my esc. My throttle neutral seems to be not well calibrate and the esc won't initiate. How can I do ?. Thanks.

Great instructional video. Can you keep them coming, on the IXSR transmitter. Would be awesome . Thanks

Thank you

Wtf? SNH(Super Not Helpful)

and what are the advantages for Straight vs portal axels??? iam new in Crawling, can someone explain?

Please take a new typhon and plug that junk in and just show us all how good it does not work . guess thats why you dont have a video on that cause it does not work TRASH. dont buy this trash

What happen to Smart telemetri... Thats annoying Spektrum Has "cancled" the "Smart" function like in the only thing NOW smart .. WFT happen

I have the Arrma Typhon 6S. So much easier than the manual. You are awesome.

Hi I just purchased two of these. Unfortunately, both of the body clips have stopped functioning on both cars after a little bit of fun in some dirt. Normal dirt, nothing crazy. It was a dirt road. Neither body will come off without an unbelievable amount of effort. Had to water down all 4 points on both cars to get the bodies off for access to the batteries. Any suggestions of how to prevent this in the future on these cars? Every single time we take them out now they both stick basically locked onto the cars. Thanks and I look forward to hearing your suggestions..

I turn it on and set the neutral put when I try to do the forward and reverse it won’t flash

How come when I talked to Losi/Horizon support, they told me the transmitter couldn't be reset to factory or calibrated like this? Sounds like some more training is in order.

So I did this and I did center my throttle and the car is running at like 15% throttle even if I turn down the th trim. What would my next step be

Been through this three times, DX6e, and it's still not right. I wish phone support was available like in the old days. For now, I own an expensive, useless helicopter.

My manual tells me to plug my flap servo into # 8 is this correct?

my batter that came with the charger only has one plug in not two so i have nothing for to plug into the negitive side

Can you set servo end points?

Lol i just broke mine, 2nd day of driving the thing. I was flying down the street and had an awkward angle and didnt see it heading towards disaster (also night time) and smashed it into a wooden stake the city puts in the ground for snowplows to avoid on the edges of the road. I hit it perfectly on the lower arm right between the wheel and bumper of course. Snapped the stake off the ground and the lower arm completely snapped and a piece busted off it lol.

Thanks, Horizon.. We love you !!

Make it easy on yourself and just set all of the expo and rates on the f switch just use 70 per on then 100 off

Would the procedure be the same for binding the SLT3 transmitter?

Is this needed out of the box? Or should it come calibrated?

What sort of range should i expect on my SLT3 transmitter to the SR315 Receiver on my mojave 4s. Some times i get half of a soccer pitch and my the car stops. I walk closer and then it establishes comms again. Is this a normal range? It seems short to me. If not, what could be affecting this. I changed the Transmitter batteries just incase it was that. Would it be worth me trying to rebind them?

Just bought heli! Could someone please tell me what my I-button does now? Which flight mode has SAFE on? Thank you!

What if you have a arrma gorgon and when you hit the throttle on the esc it goes red when you power then when you stop the red stops with the transmitter after that and noting works HELP PLEASE

Hi, my Losi micro b was linked to the transmitter when it came out of the box. I had one run then when I switched on again only the steering would work and the ESC was flashing. I tried to re-bind but I only have steering now and a slow flashing light after attempting to bind. Batteries are fully charged. Any ideas thanks

My charger never goes green and my car wont run, help!

Can I take my clipless section out and add it to a chevy 2019 proline body. Has anyone tried it?

i have the gladiator and the power wagon the power wagons great works perfect but the gladiator is stupid slow in revers speed, yes i know there crawlers but there identical trucks, both set the same f/b one just keeps in revers nothinfs twised or boggin works great in drive just super slow revers what do i need to do?

Thanks, Brad...

I’m trying to calibrate a Firma 70amp brushed esc with a Firma brushed motor. The radio is a Graupner 4ch surface radio. I turn the radio on,then the car. As soon as I do that,the motor just starts running,then stops. I go thru the calibration and still I only have full throttle,by just touching the trigger. No reverse.

Get mine tomorrow and o can't wait

Folks, use BRAKE CLEANER. Saturate it, and wait a few hours >>>> you'll see! EAZY-PEAZY!!!

Well finally figured out how to set the knob to go from 0 to 100 through the full travel. Used a mix on aux 1 as the master and the slave. Set the rate to -71 on the left and -28 on the right. Of course, the only way to set those individually is to set the mix using the steering as the master, and then switching it back to aux 1 after adjusting the rates. Also set the sub trim to 100 on aux 1

TIP: if your transmitter is beeping after you turn it on you means that the left stick/throttle stick is not in off position If helpful 👇

Firmware and drivers for a charger? What a nightmare. Who the F thinks this is a good idea when its almost impossible to charge. Mine never gets out of white so i read install all this crap on my computer and buy another usb cable bla bla bla. F yourself!

a query, change the spektrum 25 amp of the Son Uva of my son but the control does not manage to link, is an SLT2 control, what can I do or how do I to make them work

Cool! The only problem I had is that the hook and loop tape in the plane doesn’t stick

which port is it

Need to video the battery installation from the side, as you can't see the installation.

I did this and it didn't work. I did every step in the video. I've changed the servo and servo saver. My problem is the same. It turns to the left sharply and barely turns to the right. I always let the servo center itself before installing the servo saver. I had this turning problem before I replaced the servo and servo saver.

Where was the sr dial at the start? Was it fully clockwise or counter clockwise?

My gorgon was turning sharply to the left and barely to the right. I replaced the servo and servo saver. I still got the same issue. How do I fix this if as far as I can tell I can't adjust the end points on the servo

How do you change a speed gear ⚙️ in a karton 8s

Great job. Fast forward through the parts I need to see.

How do you bind this transmitter to the power wagon?

Heey,,,, I bought 4 power wagons for my kids and 2 already do not communicate.. No "bind" button on the controller,,, Something about a "bind plug" could you guide me to a video about the bind plug

My micro-B is suddenly starting in reverse! Halps! The instant i turn my transmitter on, it is full reverse if i don't have my finger on the throttle in just the right spot!

Thank you so much! I just finished collecting these new trucks, loose transmitters everywhere!