So how do you fix??

Great vid...... just changed my glow plugs on my C15...... couldn't have done it without you!

It’s not meant to go in 😂

thanks

IS this the same principal to change on a petrol engine? I have a 2014 petrol Qashqai and I keep getting a P0090 error code with amber engine light, a bit of Googling tells me the fuel filter might be at fault and I don't have the funds for a garage right now (only 8 weeks since it cost me almost £400 to get it through an MOT!) Great video as well, thanks

C15 furgoneta immortal....😂

Sometimes with sensors now i have more luck with the desgauce....😂😂😂....Meat i Dora ive given up with completely....

I have the same car. Can you confirm the torque setting please.

hi, my blower motor on same care makes a chirping noise, i want to replace blower motor, do i have to take all the dashboard out or just glovebox?

Brilliant, thanks dude.

Great temporary fix! Was hoping that's what my fiesta did, but the stud that holds the counterweight/shift arm backed out

Good videos on the injectors, would have been good if you had shown how to remove the injectors, because sometimes they can be a nightmare, another thing to point out each mark on the leak back bottles are 2.5ml not 5ml which a lot of people think they are, leak back test usually is run over a 2min period and if there is more than 20ml in any bottle then that injector is suspect, even new injectors will have a little leak back, but as pointed out in the videos 100,000 plus injectors may need looking at as part of a big service ? please do more videos on FL1 FL2 and others car thank you for sharing your knowledge

Thank you

Our pellet burner as soon as u turn it on makes the beeping noise with fan failure on display and it’s not even heated up

Excellent videos and attention to detail. Not long found your channel.surprised you don't have more subscribers maybe the channel name should have had something with automotive in it.thanks for uploading much appreciated.

Hi, how do you release the brakes in order to change the rear brake pads? Thanks.

All of sudden my Hyundai i30cw 1.6 petrol 2010 doesn't start. It cranks but show no reading on the RPM-gauge, would that be a bad sensor of some sort?

I will have to do this as soon as I got the replacement regulator. The video is already a huge help, some sequences unfortunately don't show what you are doing since the camera is spotting somewhere else..

Thank you so much for the great video. I have Hyundai i30 CW 2011. I have a weird problem. when the engine is HOT, it struggles to start. How can I solve this problem? TNX!!!

Awesome vid mate, apparantley we are having problems with the compressor. How difficult or otherwise is it to replace that?

Had one in with similar this week. Changed the rail pressure sensor as codes said it was intermittent shorting. However, the connector going to the sensor was in very poor condition - so check that first. Went to bleed the system, very poor fuel supply from filter - close to none. Crank no start. Filter is new. Took off the supply line, applied vacuum - sod all diesel came.. Blew airline back down the supply line & that gave real good diesel supply. My "theory" is either a piece of the tank pick-up is damaged/blocked or there's crud in the tank that is blocking the pick-up when the line is "sucking" - something to be aware of when dealing with this issue. Check the tank/pick-up if you're getting fuel pressure issues.

Hello, what are the torque values, master? Can you help me urgently, I will repair the same engine on Monday :)

Only video to actually help, show all the steps and angles and explain. Just did it! Big thank you!

Thanks. Very helpful teardown.

Hi was it exceisve oil consumption what was wrong with the car

what year is the skoda

halfords advanced anygood in spain? all i use back home in uk, how do you get on with replacements.

Great job

Thanks for the video. Very helpful.

Good video! But 28:28 hurt me abit

Did you change the turbo buddy? Great vid btw. Much appreciated 😊

Im working on the same kind of car, it crank and doesn't start. I checked the fuel supply is ok but the nozzles doesn't spray. What may be the cause of the problem

You need the canbus wiring loom for cars with cameras and i think thats the one you changed ti

Thank you for the great video Keep it up Very informative

State on it!!

There is a drain valve and notice underneath a red release with flat head screwdriver. Will not spray everywhere and less mess.

great, thanks!!!

Have you done the rears yet? The rear has the twist in caliper piston. I was asked to provide a tool list to do the rears but without the vehicle in front of me I can't. If you are able please post.

im trying to fit a unit in mine but struggling to sort the audio there no plug for it so brought another loom of ebay still no audio connection would no where i can get same harness as you had

Great video, dude. I just collected my car from having gearbox work done and now the reverse lights, camara and parking sensors do not work. Is it safe to asume that this switch is the cause?? Thanks a bunch

Can I drain the water by unscrewing this thing On the side?

Hi Sir, who many km have the car? I think I have the same problem. I lose power when the engine is cold, past much time since I stop it (8-9 hour). After 400 - 500 meters the problem disappear

Thank youf or this, I'm looking at buying a C4 Grand Picasso second hand and it needs this done.

Nice ppl existe, its just harder and harder to find them ... stay cool

I have hyosung 650 new starter solenoid doesnt crank and start its making click noise in solenoid do you think starter motor is busted ?

It says no signal for the backup camera because you did not plug in the RCA and signal wire. The harness @ 29:30 is the backup camera harness. For the steering wheel control to work, you have to enter in the " steering wheel control " app and program the buttons in.

Have you got a link for the disc and pads that you've used?

Great job, however, it’s easier to use a bird beak players to bend the lock pin . And no need to cut the pin. Bothe side can be bent . But I guess it’s a matter of choice. Great job

Thanks mate enjoy the video

trying to find out why I am still getting fault code when I have replaced all the glowplugs.