Where in the vehicle is the BCM and how do you remove it? 04 VW Passat wagon 2.8 litre

You should have shown where the orange latch was from the inside while the trunk was closed because I don’t see mine. My tire must be in the way and I cannot move it.

so if old flywheel is smooth no need to replace it ? im doing a base 2.0 2014 jetta and just want to get another year out of it ty

I have to replace my alternator on my ladies patriot so its easier out the bottom. Thanks KY

Thanks for the uninformative video.

Where you located fam

1:38

Felt anti-corrosion rings work marvelously. After installation, spray the terminals and connectors with protectant spray. It also works marvelously. If your battery doesn't have enough terminal to handle 1/16 of an inch, switch to an American made battery which does. Dielectric grease can help prevent corrosion, but the protective spray works better. (Sheesh. Are you a Biden voter? Everything you said/know ias wrong.)

This guy is giving bad advice ! !

NOOO! QUOTE No, dielectric grease does not conduct electricity. It is an electrical insulator in fluid form, used to prevent electrical connections from shorting out and to protect against corrosion by preventing moisture ingress. end quote

Will any mark6 Jetta radiator fan work on mark6 Jetta TDI?

How long after doing the oil change does it take to show the level. Got the oil/filter all done and it's saying unavailable.

how to reset the ASSISTPLUS when oil change is done

any idea if it is the same part for a 2014 jetta sport wagon?

Useless video...

Oil level sensors are different I think. I believe the ccta has a hole where the sensor goes on the bottom oil pan while the cbfa doesn't, it's on the block. The sticker on the timing cover should display the code unless the cover was replaced.

Right On!!! Do I have to empty the AC pump or just move it to the side?

I like how you explained everything about the job beforehand. Told me what I needed to know. Thank you.

I already managed to turn it on, I discovered the code. Now I need to know the functions and how to adjust them.

Good afternoon or good evening. Congratulations on your video. I live in Brazil and I have this radio model but I don't have the manual to show how to use it and the functions. Could you recommend a video showing me how to move? thank you very much .

Congratulations on your video. Do you know what type of plug I can put on this radio (I'm from Brazil), I bought this radio for my Audi A4 Avant 2005 (because it came without the radio) but the plugs that are in the car are different, do you know if I can buy some plugs that they sell on Aliexpress. Can you tell me the correct model, thank you. Could you also recommend a video that shows all the functions of this radio.

Can i just replace the blades ?

Yikes lol.

how did you fuck it up that badly?

holy smokes you want some taco shell with all that inside lol

dope stuff. greetings from germany/the netherlands.

big boy

That is one hefty taco buddy

don´t want to sound like dick but thats pretty normal on bmw atleast newer one

Good.job

Hi do u have a vw touareg bumper available

Great video finally someone with a jack getting it done !

Max, This is coming from a former shop teacher. You missed making this a valuable video. You went over not stripping out the bolts as you remove them.......at least three times. I get that. What you did not tell anyone is how to remove the bolts safely. You did not say anything about how to feel if you were having a problem. You did not say that you might work the bolts back and forth slightly and increase the stroke each time until they feel free. You did not say what to do if you feel like the bolt was seizing up. You did not say what you had to do if you did strip a bolt taking it out of the manifold. You did not say that once you get the manifold off, that you could take a 5mm and 6mm taps and clean out all the threaded holes in the manifold. You did not say to wire brush the bolts to clean them up if they were bad. You did not say that the cost of six new bolts is about $10-15.00 and you could simply use new bolts. You did not say that you could use anti-seize compound on the bolt threads when you reinstall everything. You missed a great opportunity. I'm sorry if this seems blunt, but you left it hanging.

That’s not how you get to the relay bro 🤦‍♂️ you take the 3 torx screws out of the bottom panel..

Oil level on instrument cluster? Lol no that's the oil pressure. If you have no pressure I bet it's your oil pump. This engine definitely has internal damage though likely because of this oil pump failure. Adding oil will do nothing.

Yea that shits fucked new engine or rebuild for sure

Moonrock Silver. Same colour as mine

It’s unbelievable that something that literally takes 10 seconds, is neglected by people. Than they go and say German cars are unreliable. Truth is, most of those people treat their cars like shit and think they’re indestructible and require nothing whatsoever.

Thank you for posting, very informative video.

That’s actually an egr not a throttle body

Omg. Shut up already. You repeated the samr thing 20 times and didn't say shit

Very helpful

Awesome two years later imma check this out!

what is the hose connected to located just below the gas filler tube on a 2006 VW New Beetle

Still got it?

What causes this to happen?

It does have that infamous Kia clacking like mine. I have a 2012 Forte EX 2.0L 4cyl 110k miles, only thing I had to fix so far was the tranny. Otherwise runs great still.

Thanks

good job

Got anything in Houston tx ?