Money!!! I was able to restart a down AP and save a trip. Thank you!

Thanks for these videos mate. Quick question dont we need to provide option 43 for APs to get the controller IP address ? Also which Access point you are using

could know how to add AP cisco on EVE ?

Can anyone please tell me what image is used in the place of "Link to physical AP"?

Why you didn't assign ip address to vlan

Thank you Sir

after the setup my radios go to up state for a sec then go back to down, any suggestion?

I got it one new command ❤❤

pls bring on more

very useful. thanks

My router is OPNSense. I have a TPLink switch between the Router and the 9800-CL. I can get the plan set up and clients to connect but cannot get them to have IPs assigned by OPNSense. Where might I be going wrong? Thanks!

Great job. Thank you.

Great. Thanks

Thank u Bro !

All to this day, I'm still waiting for someone to setup the WLC without using the wireless setup Wizard

Thanks for this video. Clear Concise To the point Nice music

Thank you.

how to make AP associated with WLC sir?

what is the default username and password on the C9800 on lab sir?

what is the default username and password on the C9800 on lab sir?

thanks so much bro

do you know hot to add new AP in EWC?

best video about WLAN ever

Thank you Sir,

Please share cisco 9800- controller Flex mode configuration video and how to adjust RF parameters values in both2.4GHz and 5 GHz.. Good video 👌

Please share cisco 9800- controller Flex mode configuration video and how to adjust RF parameters values in both2.4GHz and 5 GHz

Can you make a web authentication video please

can we install WAP in EVE-NG?

How to restore wlc back to ap?

Hi there can you please share the eve Img ?

Hey, can you share the best practice config for 5Ghz and 2.4 Ghz, please? I can assume that this is the "Typical" RF config you mentioned.

Vedio is really good but this background music is so annoying

Hi, thank you so much. as far as I understod Interface eth0/0 where AP connected is a trunk or access with vlan 10 ? it should be access? Interface eth0/1 where WLC connected is a trunk definitly, with allowed VLANs 10 and 20

Any videos on setting up ssl.

You didn’t show how to enable https management Or how to configure the management vlan on first run!

HI, This was the best video i have seen for WLAN, I have small issue with my Controller when i am using console I am able to go into into enable mode and configure mode but when i am trying SSH i am getting this error %Error in Authentication Can you please let me know what i can do to work in SSH

I can't thank you enough. I was literally struggling for this video. Finally found this. Gratitude 🙏.

Thanks, but how to add the AP ? plz make another video

Your support is 100 hundred times better than Cisco!

Thank you, it work my side

Good job. What is the configuration on the 10-Net cloud? is it cloud0 or something else? How do the host understad that this is VLAN10?

I did the same as you in the video but when I show cdp neighbor details, the switch shows up

hello I ask do you have the cisco c9800 capwap software?, I want to restore the firmware from WLC to capwap... Thank You..

I like your tutorial, thanks! Can you show how you configured your external switch (Link to Physical AP)?

Thank you!!!

sir its really very usefull ,please update more

Sir excellent way of teaching

Hi its very informative .i have issue with AP frequently disconnecting . Wlc model.8510 and version 8.3.150 AIR-CAP3602I-E-K9. Some.of AP give green and red led blanking and some are totaly green and not connected to any user. And iser faces frequently.disconnection can you help me that ..

Great Job, Appreciate it, excellent up to the point explanation.

Please share .iso img 🙏