10 жыл бұрын
10 жыл бұрын
10 жыл бұрын
Пікірлер
@Cdaprod Ай бұрын
Love the technique of pulling the wires out through the shield. Thanks for that!!
@365Condoms 8 ай бұрын
what is "an inch" ?
@foesfly3047 9 ай бұрын
I envy your precise and steady hands. You are an artisan with the pencil iron ♠️
@paulmorrey733 2 жыл бұрын
Thanks
@tyke23vids 4 жыл бұрын
Your solder-fu is impressive. This was super useful!
@foesfly3047 9 ай бұрын
“Solder-fu…” Hahaha, good one!
@avflyguy 4 жыл бұрын
What is the advantage of this type connector vs the crimp on BNC? Parts are cheaper and crimp method is so much faster....
@loyndsy 5 жыл бұрын
Thanks for posting as I'm making new p leads for my 0-200
@1967250s 5 жыл бұрын
Navy trained Avionics tech here, worked on everything from MD80s to C130s, 767, 757, 737, on and on. I have never used, or would be allowed to use, a solder joint like this. Any shielded wire would get the ground wire with at least 1 /4" join. That is way too short on the ground strip back, and is probably a brittle joint since you are moving it as it solidifies, don't care how carefully you are trying not to move it. And modern solder splices completely make this an outdated.
@Crunk99ify 4 жыл бұрын
Remember, solder is an electrical connection, not a mechanical. Also, Isodyne backshells replace solder sleeves now.
@LTVoyager 2 жыл бұрын
@@Crunk99ify Who told you that? Solder is both electrical and mechanical. What do you think holds PCB components in place?
@foesfly3047 9 ай бұрын
I thought the same thing about the creation of a brittle joint in the soldered shield. If I used this method, I’d be extra careful to leave a significant portion of the twisted shield/braid unsoldered. I would also add a second layer of heat shrink over this section to add support (add some resistance to flex) to the joint. But we aircraft maintainers can certainly obsess over which hairs to split.
@FourT6and22 5 жыл бұрын
Nice video. I do prefer to leave the shield intact around the conductors, though. Then you simply solder another lead around the shield like a ring and heat shrink all of that. Keeps the shield intact right up to the end of the conductors instead of leaving 6 inches bare. The shield is there to block noise after all. Stripping it away sort of defeats the purpose. Also soldering a separate lead around the shield instead of "tacking" the ground connection is much stronger.
@SzymonSayzProduction 6 жыл бұрын
Jeff can you run thru the wire diagram (focusing on how the current flows (which directions it goes vs blocked) thru the resisters, capacitors+ diodes, etc)
@JN03QO 6 жыл бұрын
Excellent tip for how to determine how far back to strip the jacket and the dieletric!
@hanearlpark 7 жыл бұрын
Wow. Serious virtuosity.
@dannymorgenstern1654 7 жыл бұрын
Great instruction, thanks! I'm well acquainted with solder sleeves, and a couple different techniques for using them; however, there's room for error if they aren't used correctly. The technique you demonstrated leaves little room for error and likely results in a more streamlined harness when numerous pigtails are added to a connector.
@samsungw200 9 жыл бұрын
thanks for posting
@seattledutch 9 жыл бұрын
Very helpful, thanks! Had no clue how to put it together.
@tedwaltman1 10 жыл бұрын
Another very well done "how to" video Jeff! Thank you very much for your helpful tips and for sharing your insight into this process.
@tedwaltman1 10 жыл бұрын
Jeff...nice job on your video. Nice, crisp, video. I appreciate your excellent use of the black background to focus/highlight the overall process. Well done!
@goooooort 10 жыл бұрын
Very helpful well put together tutorial, thanks.