4 ай бұрын
6 ай бұрын
8 ай бұрын
9 ай бұрын
11 ай бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
2 жыл бұрын
2 жыл бұрын
Пікірлер
@nigeldonaldson1647 Күн бұрын
what's wrong with using vaseline as a release agent, I find that works
@dr.frankensteel2759 Күн бұрын
I haven't tried that
@ronamer1 6 күн бұрын
how many volts for the start? 12 or 24? I see 2 batteries...
@dr.frankensteel2759 6 күн бұрын
24v
@dr.frankensteel2759 6 күн бұрын
And pull start
@ronamer1 6 күн бұрын
@@dr.frankensteel2759 thank you.
@superfirereptiles1041 13 күн бұрын
Are these available for purchase?
@dr.frankensteel2759 13 күн бұрын
Yes I have a few left. 40 a piece for the aluminum
@danielbutler6823 17 күн бұрын
The Yellow flame at the end was that the zinc ignited and burning? I'm asking cause this happens every time to me and it looks almost the same as when magnesium catches fire.
@dr.frankensteel2759 16 күн бұрын
Yes that's the zinc getting too hot and burning off. Be careful the fumes are very harmful to your heath
@discuswithdavis 18 күн бұрын
I really like the low cost set up. I want to build a small furnace without spending big money.
@dr.frankensteel2759 16 күн бұрын
I built the one I have with what I had or could get from home depot
@BongWaterTrader 27 күн бұрын
Would a headlight restoration kit work?
@dr.frankensteel2759 26 күн бұрын
I haven't tried it
@AznRyda001 Ай бұрын
Ooh look at the burnt zinc fumes you could of just melted empty bullet casing forba shinny scrooge McDuck coin
@dr.frankensteel2759 Ай бұрын
I did that aswell... this was an experiment
@FavoritesJ2 2 ай бұрын
Those are awesome 😎
@andrejagrujic9810 2 ай бұрын
Is glass good replacment if you can fit it?
@dr.frankensteel2759 2 ай бұрын
Actual glass.. no. Spatter sticks to it
@robconcep644 2 ай бұрын
I just put a motor on mine. It's a far improved machine now.
@gerard_3864 2 ай бұрын
Wish I has saw this video before I got some tanks.
@SilentCoyote 2 ай бұрын
This video helped me out tremendously. A buddy of mine who has owned his xA since 2006 asked me to help him work on it this weekend and I encountered the same noise you had coming from the water pump. This breakdown and diagnostic troubleshooter you produced allowed me to narrow it down before he even got over to my home shop. Immediately pulled the serpentine belt and fired it up to check if the sound vanished and it did, dropped the engine mount and lifted the engine a few inches to allow easier access to the pump and pulled and replaced it and got it back on the road with hiccups.
@IYar56 2 ай бұрын
Nickels and pre-1983 cents are the coins this Rule is meant to apply to. Just to be safe, don't destroy good zinc filled pennies. I have dug up 100's of zinc pennies that have corroded to the point of being worthless trash. My bank won't take them so they are legal tender no more, and not cents. So I toss them away(there is no away), or melt them down. What say you?
@dr.frankensteel2759 2 ай бұрын
I'd say it's better to use something that is already trash. But I don't do this regularly. Just a one off idea I had. Didn't work
@xenonkaizoko08 2 ай бұрын
sir, im filipino, may i ask you about axetylene tank inner’, is the inside fiber can iritate or dangerous? because its bad smell and i think its dangerous to our lungs
@dr.frankensteel2759 2 ай бұрын
I go over that topic on my acetylene tank re-edited version
@kylebarns 2 ай бұрын
Good video, thank you. Just went through this issue. Water pump was completely broken. Car runs like a champ now
@danielrobles3990 3 ай бұрын
Very helpful using it today
@feliciaalexander5032 3 ай бұрын
Awesome new video!
@NeBoFoRiOn 3 ай бұрын
Thanks great vid I just got a ace tank n figured I see about cutting it open I saw it was full of some thick foam looking stuff n after your vid it might not be worth my time
@piyushsonker7687 3 ай бұрын
Gjkllhh
@adamvanderlinden1477 3 ай бұрын
What did you use to reseal the intake manifold when you reinstalled it
@dr.frankensteel2759 3 ай бұрын
I used some gasket material from the auto parts store
@karthickselva6989 4 ай бұрын
Share spray model
@karthickselva6989 4 ай бұрын
Image also
@truman4956 4 ай бұрын
How many uses do you get out a mold when welding? Have you tried molding with concrete?
@dr.frankensteel2759 4 ай бұрын
I'd say 3 at most with this method. I haven't used concrete or drywall joint compound
@XiamaraTheToxicMu 4 ай бұрын
I had to cut mine as the scrapyard did not take it otherwise. I took my time, used a hammer to get the valve off... tried to flood the tank but failed. Grind the body with care and dealt with the core... it was carbon in my case. The drive stunk like acetone for 3 days but job done.
@tobe4141 4 ай бұрын
Enjoyed it, thanks
@dr.frankensteel2759 4 ай бұрын
Thanks for watching
@TheCraigMac 4 ай бұрын
the doctor is in!
@handleton7219 5 ай бұрын
Cool video, but what really caught my eye, was, is that starscream in the background? Did you make it yourself?
@dr.frankensteel2759 4 ай бұрын
Thanks. Yes I made it. Gargoyle sculpture. Have a few videos of me working on it
@frank6dnb 5 ай бұрын
I see a dude clean his cover with a hand blowtorch. Burning the fog off in passes
@browill9 6 ай бұрын
That was beautiful. Thanks for sharing
@dr.frankensteel2759 6 ай бұрын
Thank you. I'm glad you got something from it
@caroleselig303 6 ай бұрын
Beautiful!
@cindyolsonkrueger6456 6 ай бұрын
How much does it cost to fix
@dr.frankensteel2759 6 ай бұрын
The where pump is around 70 Dollars bit it depends on where you buy it. Amazon is cheaper
@Stacksz745 6 ай бұрын
In the uk after 1992 the 1 and 2 pence coins are copper coated steel 😢
@browill9 6 ай бұрын
Awesome work brother 👏. Thanx for sharing.
@phantomlexlugan6468 6 ай бұрын
Hey Man !!! Thanks for the shout out!!! Fort Payne Al. Jason 🤘
@dr.frankensteel2759 6 ай бұрын
Hey thanks for watching!
@rafadaranger 6 ай бұрын
Very nice video! Very well edited and great content! 👏🏻👏🏻👏🏻👏🏻
@dr.frankensteel2759 6 ай бұрын
Thank you!
@feliciaalexander5032 6 ай бұрын
Cool video! Keep em coming!!
@Jesusmysavior234 6 ай бұрын
I believe my scion xa is having the same problem. This video explains enough to let me d I y mine. Thank you.
@dr.frankensteel2759 6 ай бұрын
Right on glad you got something from the video
@AlpacaRenee 7 ай бұрын
Thanks to President Brandon, prices
@JIBeats 7 ай бұрын
i’m behind you
@dr.frankensteel2759 7 ай бұрын
Haha
@nathanf407 7 ай бұрын
Why dont you drive 65 instead of 60 on the freeway lol
@dr.frankensteel2759 7 ай бұрын
Because I can
@Junkitup 7 ай бұрын
One k then a hundred,!!!!!!!!
@dr.frankensteel2759 7 ай бұрын
Yes!
@mikesteiner3004 7 ай бұрын
I dare you to mount it to the hood of your car ! Awesome build ! 👏
@dr.frankensteel2759 7 ай бұрын
Haha thanks
@Sitharos 8 ай бұрын
This is the way
@coreyredding1196 8 ай бұрын
Awesome video great diagrams
@feliciaalexander5032 8 ай бұрын
Awesome video!!
@johnpaulheupel5713 8 ай бұрын
I just bought a 2005 Scion XA super cheap from a coworker's boyfriend. He actually got side swiped by a Tractor/Trailer and knocked into a ditch. It really didn't hurt it too bad. I am doing the repairs I can that are cheap or free and going to drive it. So far I've gotten the mirror re attached with a zip tie and a self tapper. I'm digging these little cars. I will probably do some repairs the right way, a little over time. Right now I just need a cheap car to get around.
@dr.frankensteel2759 8 ай бұрын
Right on. That's why I got this car. It was cheap too. Keep your oil clean and full
@johnpaulheupel5713 8 ай бұрын
@@dr.frankensteel2759 Will do. Thank you brother.
@johnpaulheupel5713 8 ай бұрын
@@dr.frankensteel2759 It seems like all of the parts are cheap except for the body parts. I guess it is because it was a 3 year only car. I work for a wrecker service so we always have pieces of old bumper covers, grills, things like that. It may end up with a Town and Country grill cut to fit. Lol
@dr.frankensteel2759 8 ай бұрын
Haha I had to put an aftermarket grill on mine
@johnpaulheupel5713 8 ай бұрын
@@dr.frankensteel2759 That is the only thing mine is still missing.
@shanesplanetshane3795 9 ай бұрын
Forgive my ignorance, but could you not make a complete circle with just one spot to weld? I guess youd have to allow a tiny bit of corkscrew to let it roll by itself for the straight ends? Im assuming you've tried that and your halves method is just easier or ends better results? Thanks for the vid!
@dr.frankensteel2759 9 ай бұрын
The corkscrew is an easy fix if you catch it before you complete your radius. In this style roller your going to have 3 to 4 inches on both ends that will not get formed ( 3 to 4 inches still straight)
@dr.frankensteel2759 9 ай бұрын
All depends on how much material you have to work with
@longdong3889 9 ай бұрын
Subscribed. Good tip.
@dr.frankensteel2759 9 ай бұрын
Thank you
@TheDeadheadable 9 ай бұрын
If you just wanted to add the zink to brass why not just throw in the pennies the way they are. Why the extra step.
@dr.frankensteel2759 9 ай бұрын
Because I'm trying to get away from the copper color
@jonathanozment4523 9 ай бұрын
Isnt car tire weights mainly zinc now. Most are avoiding lead for obvious reasons
@dr.frankensteel2759 9 ай бұрын
I thought they were mainly lead
@derekmcdanold7108 9 ай бұрын
I'm pretty sure you just posted a federal crime on KZbin
@dr.frankensteel2759 9 ай бұрын
I almost deleted this video. Look it up... it is but at the same time it isn't.... look it up
@dr.frankensteel2759 9 ай бұрын
I'd like to hear about what you find
@CleveDawgPound 9 ай бұрын
(a) Any person who exports, melts, or treats 5-cent coins or one-cent coins of the United States in violation of § 82.1 shall be subject to the penalties specified in 31 U.S.C. 5111(d), including a fine of not more than $10,000 and/or imprisonment of not more than 5 years.
@CleveDawgPound 9 ай бұрын
Link to full code: www.ecfr.gov/current/title-31/subtitle-B/chapter-I/part-82#
@CleveDawgPound 9 ай бұрын
This is where you are probably ok as you stated one-time, not going to sell, etc. : (b) The prohibition contained in § 82.1 against the treatment of 5-cent coins and one-cent coins shall not apply to the treatment of these coins for educational, amusement, novelty, jewelry, and similar purposes as long as the volumes treated and the nature of the treatment makes it clear that such treatment is not intended as a means by which to profit solely from the value of the metal content of the coins.