Hy work in time Muscat Oman engineering company i work opperter machine bending opperter i need to meet you jop sir
@terrydaniell2409 Жыл бұрын
That was not prewired into the load side.....
@andygaudet2 жыл бұрын
She’s beautiful, not just cute.
@gford14912 жыл бұрын
Only problem with testing continuity is you can have all the wires broken but one and still give you a good continuity signal
@juliacampos30342 жыл бұрын
𝓹𝓻𝓸𝓶𝓸𝓼𝓶
@manojjayasundara82942 жыл бұрын
hi ,i need your support plz drop your mail address
@kefpull66762 жыл бұрын
this is the reason KZbin is a good platform
@mrow17842 жыл бұрын
Hooray, someone who actually showed how to test for continuity without droning on with irrelevant confusing mumbo jumbo.
@alkamzine83362 жыл бұрын
I like you Girl, Wanna Scratch me with your Lovely Nails? 😊
@fix-it-right51872 жыл бұрын
What will happen if you have a multimeter that does not sound but only gives number? What number should you be looking for then? Great video btw. Thanks
@dodgeshadow0992 жыл бұрын
if there is no continuity it should show OL or open loop. if there is continuity you should see a small resistance value almost near zero.
@MrSeananners123452 жыл бұрын
I really think me and you could have a spark between us
@bikerjon1532 жыл бұрын
Reading from a board.
@RamRam-wb9nw2 жыл бұрын
Wait there's a multimeter in this video?
@enigma18632 жыл бұрын
She is cute
@AceHi8082 жыл бұрын
I wouldn’t miss a day of class
@creekwalker622 жыл бұрын
What if both ends of the wire are yards apart and your multi meter doesnt have nearly enough wire to reach both ends of the wire you are checking for continuity?
@PowerAssemblies2 жыл бұрын
Be sure that the power to the circuit is turned OFF. Next, tie the wire you would like to test into the ground or neutral wire. Next, head over to the other end of the wire and touch one of your leads on the multimeter to the ground if you tied it to the ground (or neutral if you tied it to the neutral), then touch your other lead to each wire until you verify which one is correct. Finally, mark that wire with electrical tape for verification purposes. Continue the process until you have verified each wire. I hope that helps!
@creekwalker622 жыл бұрын
@@PowerAssemblies thank you for the reply 🙏 I will try this technique.
@ghulabkhan7622 жыл бұрын
Good morning
@christophewagner40282 жыл бұрын
Perfect thanks
@edgrrickett1402 жыл бұрын
So it's alfully hard for an old guy like me to learn about continuity lookin at her
@damon123jones2 жыл бұрын
How cute...i love girls
@lewismacdonald15162 жыл бұрын
Your two minute video explained this far better than a 20 min video I just watched, thank you!
@PowerAssemblies2 жыл бұрын
We're glad that we could help!! Thank you for watching.
@ghulabkhan7622 жыл бұрын
Wah
@SeaMonkey1372 жыл бұрын
Simple and straightforward, just like it should be.
@Heywoodj19693 жыл бұрын
I always put my strain relief copper coil “tail” INSIDE the copper wrapped sleeve, just so that it’s tucked in to the wire assy.