What gears were you running in that and was there any precocking?
@tipzy773012 күн бұрын
Retro arms 20:1 dsg set and precocking to the max
@wyz228514 күн бұрын
Solink is running a promo on their budget brushless which makes it even cheaper than this. From my experience they are more ETU compatible as well.
@tipzy773014 күн бұрын
You didn't see the v5 sitting in the top right? Or did u comment n move on. Rude.
@wyz228514 күн бұрын
@@tipzy7730 Sorry, didn't mean any harm. I only commented because I saw your description said to use only with T238 ETU
@tipzy773014 күн бұрын
Yea, it's t238s legal disclaimer. They asked I put it in the description. I used Levi in this vid. We've spoke in the ASM discord about the response briefly, so u knew this. Sorry, no harm ment by me either, just found it a bit rude.
@wyz228514 күн бұрын
@@tipzy7730 if so, feel free to remove my comment:), truely only wanted to show the viewers options
@wyz228513 күн бұрын
@@tipzy7730 Sorry, didn't mean so. I didn't know that, and I only wanted the viewers to know there are alternatives that are perhaps better (I didn't have any sponsorship actually to tell me what to do/not to do)
@Mirko-w9f20 күн бұрын
This motor work whit titan gate?
@tipzy773020 күн бұрын
i dont have a titan to try, but with brushless mode it should. but beware, it will void your warranty. i use perun and leviathan no problem, but still voids the warranty.
@JonZis202322 күн бұрын
How do you rank it vs the T238 silver and the paragon ?
@tipzy773021 күн бұрын
Honestly, I would grab a blue over the silvers unless you need the adjustable speed. The Paragon motor is sold out, but from what I can tell it has custom, hand done windings, a pretty can and tower, and the new processor t238 is using on the new blues and new gen silvers. At 80 bucks you can't beat them without running into huge diminished returns. The Solink v5 offers the unidirectional bearing, but is 100 more + the cost of the programing card, so like 220 total.
@T238-u6m25 күн бұрын
Thanks for the review Tipzy.
@tipzy773026 күн бұрын
I was EXTREAMLY impressed by what t238 brought to the table as a budget option to brushless airsoft motors. would honestly recommend it 10/10
@tipzy773012 күн бұрын
some of these motors make a ticking noise, i can cause it to happen when i alter the rof with levi on non brushless mode, but if its on brushless mode rof works great, the tick in my motor goes away quickly, while others report the tick no matter what.
@jerryglez208928 күн бұрын
Toys for children who believe they are soldiers
@tipzy773028 күн бұрын
comments form people that think they better then everyone, come back to reality bud.
@joewaffle566628 күн бұрын
I have the same lpvo on my actual AR and it holds zero believe it or not lmao
@tipzy773028 күн бұрын
Lol, I believe it. That's why I went with it. Amazing lvpo for under 100 on sale.
@tipzy7730Ай бұрын
a perun or titan is needed to use an air break. if you want to use levi or aster the sector gear must be split and the bottom half rotated 180 degrees so the cut off cam is at the end of the cycle ensuring the sector doesn't rotate in the way of the piston at the end of the cycle.
@jondbaptist36942 ай бұрын
Insane
@sherbetdab60662 ай бұрын
This looks just as much,if not More fun than a lot of real firearms you see on here!!👍😁
@tipzy77302 ай бұрын
yea, building airsoft guns brings a fun mechanical challenge. lots of expensive moving parts in these as well lol. at least the ammo is cheaper.
@tipzy77302 ай бұрын
these are the solink 13:1 lightened helical gears on the first t238 i bought. it was off amazon almost 2yrs ago, says 33k but running a bit faster.
@Teotret13 ай бұрын
Nice Paint NOT hahahahaahah
@tipzy77303 ай бұрын
Not another jelly samich. Sorry u are like this.
@exmachina26003 ай бұрын
u a brappa
@tipzy77303 ай бұрын
Idk what a brappa is, so probably not.
@exmachina26003 ай бұрын
@@tipzy7730 classic brappa response
@tipzy77303 ай бұрын
@@exmachina2600 sounds like something a jelly hater would say. sorry you are this way
@exmachina26003 ай бұрын
@@tipzy7730 keep brappin brappa
@tipzy77303 ай бұрын
@@exmachina2600keep getting jealous and leaving me cry baby comments, it helps! Remember to also like and sub!
@reptileguy8574 ай бұрын
My don’t you film anymore?
@tipzy77304 ай бұрын
working with solink 13:1 helical set rn, ill post a vid of it for ya later
@BeWolf.4 ай бұрын
Where's the full auto? 🤷🏻😂😂😂
@tipzy77304 ай бұрын
It didn't survive binary, but was fun.
@BeanMan35995 ай бұрын
how did you get it to basically not sound like an aeg
@tipzy77305 ай бұрын
I hope in a good way. Lol. Follow Paragon armorys shimming guide. Alot of the unwanted sound is removed when you shimm the motor to grip and tower to gb. The only thing I'd add to that vid is pay attention to sector gear height. It can wind up to high for shs pistons
@batzarrosdefijourney69705 ай бұрын
In the thumbnail it looks like you have a normal tooth piston rack doesnt the aztek dsg require to use their special rack?
@tipzy77305 ай бұрын
yea, i took this pic to show what the gears looked like after cleaning them. there was lots of oily rust and lazer etching slag left on the gear. i had random things in the pic to show color.
@batzarrosdefijourney69705 ай бұрын
@tipzy7730 what mosfet did you use ? The website says you have to use a leviathan
@tipzy77305 ай бұрын
@@batzarrosdefijourney6970 i used a levi, but i think aster and perun should work also, as long as it cutting the cycle from the cam and not teeth i believe.
@mixerngzishot5 ай бұрын
Can someone please tell me how to swap my trigger, I recently bought a new trigger, dont know how to replace it, and cannot find any tutorials. Please give me a short explanation.
@tipzy77305 ай бұрын
Disassemble your gun and remove the gear box from the reciever. Open gearbox, while doing this make sure no shims on the gears get out of place. After this it's a pretty straightforward swap. Just make sure all the shims were where they were when putting it back together. May have to re use the old trigger spring.
@bubula15446 ай бұрын
go laser game....
@tipzy77306 ай бұрын
What dis mean?
@strykergaming99666 ай бұрын
@@tipzy7730I think he means laser tag but that’s gay😊
@DSG_DRC6 ай бұрын
did you just jb weld it back together and leave no screws? cuz i had the same thing happen i didnt check the screws and they came loose and stripped
@tipzy77306 ай бұрын
i use'd new screws when i jb welded it to gether. i have also jb welded a sr25 sector with no screws and it lasted. you should be good just let it cure for a good 48hrs
@reptileguy8576 ай бұрын
Hi
@tipzy77306 ай бұрын
sup
@thegermanbadger83916 ай бұрын
How much for you to build me a tsg gearbox that shoots 350
@reptileguy8576 ай бұрын
Thanks for liking my comment!
@reptileguy8576 ай бұрын
Cool!❤
@peeque99046 ай бұрын
What fps do you get?
@tipzy77306 ай бұрын
i didn't get to chrono it. put a couple mags threw it and when i switched to binary it pme'd into shearing a spur axle. was great while it lasted tho.
@reptileguy8576 ай бұрын
BRO WHAT HOW IT DOESN’T’T EVEN LOOK LIKE ITS MOVING😮
@tipzy77306 ай бұрын
😂
@reptileguy8576 ай бұрын
@@tipzy7730 Thank for liking my comment
@justplainjosh.7 ай бұрын
where are the siegetek gears in stock? also how much did you pay for the set?
@tipzy77307 ай бұрын
lol, i may have gotten the last 2 useable dsg sets from stampedetatical for 145. seigetek's websites says: Due to various disruptions to our manufacturing capabilities, there is currently no ETA for our out of stock gear sets until everything is resolved. Thank you for your patience, understanding, and continued support.
@ccddtt1237 ай бұрын
meal team six
@tipzy77307 ай бұрын
🤣
@andrewcarp78427 ай бұрын
Short stroked?
@tipzy77307 ай бұрын
1t
@MK05098 ай бұрын
Can you please give parts list I literally love this 😻
@tipzy77308 ай бұрын
the base gun is an emg f4 sbr, falcor straight jacket outter barrel, buffer back plate of buffertube off of a ares sr15, pts eps, pts epg-c, bifrost, RA split gearbox, solink 12:1 gears, paragon armory j cage bearings, fps softair piston head, guarder cyl head, vfc m4 noz, guarder tappet, mec tappet spring, leviathon optical, aztech hybrid arl, fps softair cyl, retroarms piston, m135 spring, maxx hop, madbull shark bucking, edgi 300mm inner, max adj trigger modded for levi, t238 33k, or warhead 31k ovonic 50c batteryt28 3
@s989589 ай бұрын
Nice build. Where do you get Solink gears from?
@tipzy77309 ай бұрын
brillarmory.
@DeliciousDogMeat10 ай бұрын
gaming
@tipzy773010 ай бұрын
for 30 bucks these solink gears are very nice. noticeably nicer then shs/rocket. the bevel has tons of room for shimming. just wash the protective oil off before using them and lock tite the sector gear screws.
@TotshotAirsoft9 ай бұрын
i was told they are just shs gears rebranded
@tipzy77309 ай бұрын
@@TotshotAirsoftthen explain the helical 13:1's prtty sure thats not shs. i got a set them also but they require a lot of room for shimming and all my gearboxes have ezo bearings. gonna get sum flt bushings n retry them sum time later. i thought the ezo's would be stronk enough to handle the axle load but the play in the bearings just doesn't let them mesh well under load. 10/10 quality tho.
@TotshotAirsoft9 ай бұрын
@@tipzy7730 i’m really not sure thats just what I was told when I asked about them. Multiple people seemed to agree with the dude.
@tipzy77309 ай бұрын
@@TotshotAirsoftyea, the parts world is weird. But solink also has slim brushless motors which are the first Ive seem. I truly don't believe shs is solink OEM. Maybe ko ventures. The OEM for warhead. I recall warhead posting about gears they had coming out that never saw the light of day that had similar packaging to the solinks. Not to mention warhead went quiet like a yr ago
@anzu6086 ай бұрын
@@tipzy7730There's not that many OEMs for airsoft parts, Solink gears might very well be made by the same factory as SHS, just to a higher standard. I'm not familiar with gear cutting though, might be that they're buying them from a different place so that they can get them helical cut, or have the machinery to cut them themselves. Doesn't really matter in the end, they're better gears for a similar price.
@jaxattacks-rp5vo10 ай бұрын
what safety’s are those?
@tipzy773010 ай бұрын
pretty sure the bunny ears are am style 4 and the palm is the stock one that comes with the nightshade.
@punk857010 ай бұрын
that brushless changes the noise so much, I might have to invest lol.
@AshmalFloresAtoma10 ай бұрын
Sir is it airsoft or a gel blaster?
@tipzy773010 ай бұрын
Airsoft. But the only real difference is the noz and inner size