how did you get the drywall lifter to tilt the other way? I am doing the same ;ift up to a 22.5 degrees ceiling and my lifter dosent tilt in the longways direction.

Hey man I don’t know if you’ll see this but I’m trying to do this on my floor soon with no experience. I’m trying to overlay it on top of planks ( 2” width) that run across the floor, I’m going to try to fill in the gaps between the planks before I apply primer and then the leveling compound. Can I do it that way or does it have to be applied directly onto plywood? I was hoping I wouldn’t have to remove the planks because that would require ripping up major sections of my house to get to them fully.

Im using a ryobi brad nailer so far is working great

But how

Super confused. How does this show how to cover exposed ducts? Suddenly they got painted?

So after describing you technically lower the height of the base (from the bottom) at the high poins of the floor to even it out. What happens if the adjacent walls are flat & level? The base for those walls will now be much taller than the scribed base.

Doesn't seem to fix the problem I wouldn't think

So.. you moved a single plank about 2mm, if I understand your Queen's Canadian, and joined the broken lock on this end. So... what happened at the other end of that plank?

Genius 😉

Nice, but too slim.

* low whistle *

Greenboard mold resistant drywall above the shower kit and on the ceiling?

Great job you did. I love that you're very organized. I'm about to install 2"X2" black hexagon tiles inside the shower pan, but the corners of the shower pan aren't squared. How do i handle this issue? Thanks.

I need to get those tile nippers, but I don't know what size or particular brand. Suggestions?

Just install secondgary glazing with acrylic glass

Shoudn't the side wall tile be started in the center of those walls so you end up with equal cuts on the ends?

I would of at least re sealed the sink😂. But then again I probably would have ripped it all out.

Nice vid! Very helpful.

If I designed my own house, I would have walk-in showers measuring 4 x 4

I was a custom home builder. I have found high mass vinyl or these best lead drywall or lead sheets as used in x ray rooms for dentists is the greatest . You are informed and I. Commend you because you must measure the entire assembly as a unit. On my office I added mechanical drop down door sweeps and double doors ion. My office entrance

I've done DIY and basement finishing on mine and 3 of my kid's houses, and it never fails when I install a pre-hung door, then take it off to paint it, that when I put it back on there is all of a sudden an alignment problem. I'm very careful not to get paint on/in the hinges, or put to much on the door edges. Videos like these, as well as a couple of others, always let me fix the problems. It always comes down to one of 3 solutions: 1. Remove and reinstall the door stops. Usually the hinge side and/or top (as shown in other videos) 2. Either bend or stretch the hinge (as shown in other videos) 3. Add shims behind the hinges (like this video) I've also seen videos where they move the hinge out, fill the old holes with wood splinters, and then re screw in. I think it's easier to move the door stops and less risk with too many holes in a small area. You really need to think of it as a "rectangle in a rectangle" and look at the whole picture to see what your specific cause is and the best solution. Glad there are videos like this still to help the DIY'ers!

I caanot find ur 1st coat video

I have tiles half way up the wall in the bathroom that are really ugly. If I remove the tiles like you did could I add wainscoting over the old tile glue instead of making the walls all drywall?

An awesome makeover!

kinda worked. door is not hinge bound and will close, but now latch side edge rubs

excellent

If im using penny tiles, can i just put thinset over the levelquick stuff and call it a day or do i have to put down a sheet membrane?

How tall are you?

Thank you for a straightforward, no frills how-to!

What are the tools you used? Maybe we need those names, douche. 🤦‍♂️👎🚶‍♂️‍➡️

Bro where do you get the parts? Like the frame and glass can we customize it? Length and width

Hi! Where did you get the tile? Could you list the info for it?

I just called their customer support and thye said schulter ditra cannot be installed on tile smaller than 2"x2". Do you think it works okay?

Did you use a 1/4" trowel? Also, is it necessary to fill in the sides with 1/2 pieces if it will be covered with trim?

Im 5 ft 11 83 kilo. What size would you recommend? Thanks

Looks fantastic.. another nice “,clean “makeover”👍

The client is pleased.

Great job mate, the hood comment has prevented me from making an expensive mistake on this one. This is the kind of review we need for every product! Sick of over produced sponsored videos reeling off a fact sheet with a fully grown man pulling an idiot face in the thumbnail.

Kitchen counters with cigarette burns really bring me back lol

Thanks for sharing the video. 🫡🫵🏼 I’ve been trying to get sono panel in Pennsylvania, but it was only sold in Canada now they’re doing sales in the USA only at Home Depot‘s so I’m excited to work with it. 💪🏼🤙🏼💯💯

4:20 I like the swirled swear look best 🤟

The Milwaukee will turn off on you after a certain amount of time, the Dewalt is ready to go as soon as the trigger as pulled. Milwaukee won’t sell you parts to repair their gun, DeWalt will. Both nail guns are fantastic but getting up on a ladder on a high ceiling for whatever and not having the gun ready is a pain in the ass. Either way they both blow Makita nailers out of the water.

For better bonding it’s recommended that you make a “primer” by mixing 4:1 water:redgard and painting that on first

Awesome video!! Getting ready to do my 40 x 40 pole barn/garage !! Thanks for the great ideas!!!!

Are the GRK screws better because they have that extra fancy thread on the top half???

How do you ensure the lift hinges at the top and doesn't just hinge as you lift it, dumping the drywall off the end?

Awesome work

man you should have used the orange schluter membrane for the tile, we sell it at lowes and its LEAGUES better than your ready set

This is done incorrectly. Should be using the orange underlay to avoid cracking. The underlay costs more than the tile but you only do it once.

The door jamb is probably the most important line in the room but i cant help but wonder how you finished the opposite corner and got out the room 😅😂