@@Slidelikely Not likely…you talking about the air injection pump right?! It’s not uncommon to have air injection pump fail, it should sound like a vacuum cleaner wen on, if it’s abnormally loud you should change it

@@valentinhristov264 I would assume so but I guess the m271 motor doesn't have it when you search it, you'll find info on c300 / 350 or just different Mercedes motors

@@Slidelikely you have to go to actual shop and have it diagnosed properly, there are many things that make abnormal noises when engine is running.this video was for low boost fault,if there is no low boost fault then u have different problems. Good luck

@@bsultan77 🤔 check on the back of the supercharger by the throttle body ( driver side) u have a plug there for vacuum booster that is capped on yours because u have sbc system . Also pipe for evap system close next to the cap. Did you du a good smoke test?I would not start changing parts yet. If smooth idle values are good. Other not nice place for vacuum leak is the bypass throttle body seal.

@@Tommygunn1 don’t overthink it . Like sed to the other guy. Snug it , give it a 1/4 turn and you are good. It’s not rotational mass or cylinder head bolt so it has to be absolutely to spec

@@bsultan77 Hello, make sure u du leak down test on the delayed cylinders, Check for vacuum leaks.This fault is very tricky and it can virtually be anything. I also changed throttle body later on. Good luck

@@DeryaOzgunYalcn low boost pressure fault. Light will come on after the second Time I start the car

@@tweedledee5850 snug the bolt , give it 1/4 turn pass the snug point and u should be good to go. Don’t know exactly what the torque spec is , on bolt this size not more then 30 foot pounds

@@joshv7109 that is correct you will need to replace everything I replaced. ABC suspension cars don’t have sway bars, that’s why Arnott is not advertising this kit for ABC suspension… I must say it was totally worth duing this , it’s been several years since this conversation, it’s so nice that you can park your car and not find it sitting on the ground after 2 days. Arnott also makes a more sporty kit with bilstein shocks for w220 . The kit I installed puts the suspension in comfort

Thank you…I spent a lot of time realigning everything, I just have to push through the long sanding process.take care

Yeah… I just need to not look at the car for couple days and regroup…trouble is I used this to fix couple spots on the rear bumper and side skirt. So that has to be removed and redone…anyway thank you for the support

You have to check for vacuum leaks before replacing anything. Smoke test first. Common vacuum leak is seal ring at brake booster hose . Or it’s maybe a cap on e55 because e55 has different brake system.

@@valentinhristov264 i have 82mm tb but stock tune,

@@endri15255 that will not work…why did you go for bigger throttle body?! The restriction on these engines is in the manifolds. You should put headers before anything else. Throttle body is probably good for up to 650 horse.

@@valentinhristov264 i have headers also but i mess up somethin with ecu but now all good i replaced my ecu from a cls55 2005,car runningbgreat only this eerror im seeing load limit active p1999

@@endri15255 so runs and drives fine but the fault appears? Triggers check engine light or just sits in the ECU memory with out check engine light

Hi! It’s a second gen hood that I am modifying to fit first gen pop up headlights

Hey! Well the thing is I don’t have much free time and it will take forever to film the process…. So ideally you will have a press to press the cup flange out , if not then u can use a crankshaft pulley puller, just find 2 long bolts that u can bolt to the cup. Punch mark the splines with the cup before anything…I still have the old support bearings, will make a video later today or tomorrow

kzbin.info/www/bejne/Z5ywmquaZZuMj7ssi=k0Wll1XP2O25xw3W Here is part 2

Hi! Well that’s the point of this video, it’s a failing valve block

I don’t understand

Zdravei ! Pishi tuk, kakvo iskash da pitash

Hey ! Sway bars are not needed with the hydraulic suspension system. They are absolute must if u install conventional suspension , especially on heavy and powerful car

@@valentinhristov264 No, they are not.

What du u mean by “drops away “ ? The car drops on the ground after hitting a bump and won’t recover?!

Yes it fits… that is not a part listed that fits this car. Double idler is sold as un assembly from mercedes Benz . It’s not ment to be serviced

@@valentinhristov264 thank you so much 🙏

You are welcome…just don’t by used throttle body, I did that at some point and got misled, also know that idle in park on these cars is not as even , idle is steady wen u engage gear and hold the brake… good luck

Thank you! Please look at the second video, it end up been combined problem with throttle body. There is a link to cheap OEM throttle body at second video…

Hi ! I believe you asking for the 6s electronics car. ESC pad,servo mount , offset servo horn and steering link is all u need for that. These came in every 1/8 scale arrma 6s buggy (typhoon, kraton, ) up to version 4. I think the change design for version 5. . Here is everything you need 13$ …. www.ebay.com/itm/225164875090?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=JILWqMHDS7e&sssrc=2349624&ssuid=kCwRfMH7R36&var=&widget_ver=artemis&media=COPY

@@valentinhristov264 Thanks man 👍

@@SethMaetric …forgot you also need the receiver box… u can use anything there. If you are racing , make the saddle pack car , if you are in to more having fun then make the 6s car. Both cars are competitive and fast in a different manner,saddle packs is easyer to drive, 6s car is more fun to slide around the corners

@@valentinhristov264 im racing with my 20' xb8e with single brick battery layout. Wanna try your layout to see if is more balanced. I'll arrange the radio box with a 3d printer.

Yeah it was fun experimenting. This setup sounded very clean and not to loud. Almost no drone

@@valentinhristov264 it makes me want to cut up my Borla S pipes. I found the video and the Corvette Forum thread when looking for ideas on adding a dual in/dual out resonator or pair of resonators mid-line before the axles. Your work is awesome.

@@brett31979 it makes your ears ring for half un hour after u drive the car I bet. I sill have the pipes that go over the rear axle with a t pipe welded on them. Regular metal pipe is better than stainless for the muffler end of the system… it’s a lot to say about it. Let me know if u are going to build something, we can talk so I can explain what was the most effective way to build this

@@valentinhristov264 my daily 99 is a stock engine with headers. It does not bother me at all, though the car is sound deadened and insulated. Both are, actually. But the 03 Z06 is going to be a blown 402 with moderate cam, headers et al. At 43 I no longer enjoy noise for the sake of noise and want to better muffle the Z06. I probably won't get into changing the exhaust around much until the project is finished over the winter and I know what dimensions I have and where since it also has a 6060 and C6Z diff which will require some pipe cutting. I appreciate your offer and may take you up on it when ready.

There is no idle air valve , idle air valves were used on older vehicles. Bypassing the cable operated throttle body. This is computer controlled throttle body. Takes signal from gas pedal potentiometer and applys voltage to throttle body motor. Throttle body potentiometer tells the computer throttle body position and air flow. It throws lean fault because it opens the throttle body more then what it tells the computer and allows more air .computer then adds fuel to correct condition. The signal from throttle body is incorrect

Hey glad to hear from you! I have been busy past probably 4 months now getting this car going back from the dead. Cl55 is fine , it needs new a/c compressor but otherwise it’s been great and you are right it’s hard to replace it,wen I have a crappy day and sit in that car after work to get home feels like all the problems are gone , it’s simply one of the nicest cars ever. As far as getting W222… I got to tell u I work on Mercedes every day and anything newer then 2006 got problems that it’s gonna make u Hate these cars. No access to ECU options coding, trans problems, Engine timing chain problems, turbos failing…beautiful car but even I can fix them I don’t want to own one. Vr4 is gonna be my new daily driver and it’s 4 wheel drive so I can drive it winter time. How are you been ?! Hope all is well

@@valentinhristov264 good to hear you're doing well. I'll take your advice on the w222 into consideration. Hey Valentin, remember how your using the ABC reservoir for the split cooling, I was thinking of rerouting that set up into a tank. Like use that as a un der hood tank. I know it's pretty small but I think it'll help a little. What you think? Cap off the screw on cap so it can still purge and add ice and drill a return line .

@@300zVinh …that’s drag racing stuff , there is plenty of videos where they even route the a/c to cool the intake charge…it is absolutely unnecessary on a street driven car. In drag racing you want the car to be consistent because most of the time is bracket race so you are chasing the time u submitted. So after couple run car gets hot and slows down a bit, there for you put fans to blow on the engine and ice in the intercooler tank to bring the temp down. These cars have protection if intake temp is too hot it will turn off the supercharger. I went 2 wice drag racing with my CL it never had un issue, that’s at 90f ambient temp. The abc reservoir has a good capacity. So it goes like this the bigger coolant capacity the faster recovery time, longer pulls…

@@valentinhristov264 ok, guess I'll leave it alone. Thanks again

Sounds like u have misfire on the whole left bank of the engine. I would check the air injection valve first. These valves don’t fail often but … just remove the hose from the valve and see if it’s black in there and start the car. If exhaust is coming through the valve then it’s messing up the fuel mixture on that bank because it’s adding air to the exhaust gasses…

@@valentinhristov264 I will

@@valentinhristov264 sorry my bad the smooth running test for cylinder 6 and 3 not 5 showing me high values

Tazi greshka e za bedna smes ne za problem sus kuso za benzinovata pompa. Predi sedmica ka4ih video v koeto obiasnih 4e problema e vuv droselovata klapa.Proveri za te4 na vakuum sled droselovata klapa, ako nimash te4 smeni klapata.Klapata e sushtata kato na dvigatela brz kompressor, Sami triabva da polzvash tvoia kabel i da razlepish iZulaciata.ima vtora 4ast na tova video vuv moire videota gledai ia.

www.ebay.com/itm/275027838656?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=0aYESlQHSae&sssrc=2349624&ssuid=kCwRfMH7R36&var=&widget_ver=artemis&media=COPY

Не съм в щатите,но благодаря все пак за помощта. Искам още нещо да питам за SBC спирачките дава ми грешка reservoir pressure p2131 на живи данни показва 117 бара налягане а границите са от 69-110 бара. Какво ще ме посъветвате да сменя сферата или е някъде проблема?

@@bobbyd.7853 tazi sistema ima dojivotna garancia it’s Mercedes benz.poneje e sistema za sigurnost, tuk ako imash problem sus tazi sistema, triabva da otidesh pri dilar na Mercedes i ia popraviat bezplatno.ne mojesh da comunicirash dobre sus tazi systema ako niamash zavodski skenner i shte ti dava greshna informacia. She pogledna utre kato otida na rabota kakvo e obozna4enieto za tazi greska

@@valentinhristov264 тук в UK е 10г гаранцията, след това искат да си платиш. Цената е колкото половина кола.

Watch all I think 5 videos, u will find out everything u need. You are looking at ruffle 2000$ in parts. Arnott is the name of the company and they have 2 options to choose from . One is more comfort what I installed and sport option with bilstein shocks

@@valentinhristov264 Thanks from Northern California!

Oregon. I got a tell you it’s been few years now, it made the car stress free…no parking and go back to find your car flat on the ground