Como faço pra traduzir em português, sou fã das válvulas bray
@CantizeSay Жыл бұрын
you didn't put back the springs before inserting the end caps
@MalangPartschina2 жыл бұрын
Nice video,if you need cheap and good-quality crankshaft or other truck accessories,pls contact me,our company have a discount and free gift this month
@anilkumaryadav28852 жыл бұрын
Very good
@evgeniyzakharov95752 жыл бұрын
Thank you
@Hewagej2 жыл бұрын
Nice video Thank you so match for share your video
@roadhog883 жыл бұрын
Springs?
@ikechinix95243 жыл бұрын
Many thanks for the video. How about the spring cartridges on both ends? I didn’t see any when you dismantled the valve. I believe the valve should be a double acting position type.
@ymoatassimbillah3 жыл бұрын
We have many of this actuator in different sizes here in morocco. This video really helps..
@johnjustice88603 жыл бұрын
Why didn’t you put the springs in?
@klyetry25272 жыл бұрын
No springs, double acting.
@mr.nizamulhoq8514 жыл бұрын
Hello Sir, Have a good day. I have recently facing problem in a newly buying Siemens PS2(2wire, 4-20ma, 2 wire, without HART) smart positioner connect with my existing Single acting, air to open linear actuator(pneumatic control valve) having 20mm stroke when I am going to newly calibation. During commissioning this new positioner with existing control valve/actuator in initial condition its display shows P 85 and NOINI mode, at that time when if i press (+) and (-) button then the actuator totally doesn’t not move.only small clicking sound hearing inside the positioner and little air Release from actuating pressure line(Y1) of positioner , however pneumatic(4kg air pressure) and electrical(4ma , 24VDc) connection is ok there. Interesting matter is, if i place old existing positioner there then it easily move the actuator after pressing (+) and (- ) key in P85, NOINI mode. Is there any problem of lever setting or restrictor setting there.i don’t change any restrictor setting in this newly buying positioner during commissioning there.i am confused if there any setting required in restrictor at positioner during newly commissioning? I depreciating if anybody here who can advice me kindly please to fix this problem.
@narayanjagtap66854 жыл бұрын
👌👌👌👌👌
@chrisrobinson54845 жыл бұрын
A LITTLE BIT CLOSER? O MY GOD!
@chrisrobinson54845 жыл бұрын
PLEASE tel me you have not been endorsed by EMERSON......
@duramax785 жыл бұрын
Can anyone tell me what the main body on these are made of, also the ends and insides I have a few I’m scrapping, one small one like this and some bigger ones.
@shivakumar-zw1gp5 жыл бұрын
How you aligned the piston with pinion ?
@BingeDrifter5 жыл бұрын
Ummm can't you lift the actuator off the square drive and install it back one flat over on the valve shaft?
@judyzhao47346 жыл бұрын
Great video. Guys also can contact me at sales@ veson-valve.com for more information about this kind of pneumatic actuator.
@duramax785 жыл бұрын
Would you know the materials in these units.? Thanks so much.
@cristaljin74246 жыл бұрын
pneumatic actuator AT 52 DA USD20/pc
@GearsyGGAA8 жыл бұрын
Great video. This just helped me out a ton on a project that we're involved in. 169 actuated units and 10 had to have this done. Thank you for the video
@Jeffreyp035 жыл бұрын
,
@proval-dorukendustri78628 жыл бұрын
Hi from Turkey. Great video. Check out our pneumatic actuator animation as well.
@savagesosa9 жыл бұрын
These are a pain. The video really did help alot thanks
@tri-statevalveinstrumentin86179 жыл бұрын
+Javier Sotero Hi Javier, no problem, I'm glad the video helped
@chrishowton19 жыл бұрын
dude, thanks for making this video, we have a ton of these things at our facility and when i rebuild them I always get my a$$ handed to me when putting the pistons back in. Thanks to your video and that little teeth skip trick the one I did today went smooth. thanks again
@tri-statevalveinstrumentin86179 жыл бұрын
chris howton Hi Chris, I'm glad this video was useful. This is the first feedback we've received.
@chrishowton19 жыл бұрын
Tri-State Valve & Instrument, Inc. Thanks again, showed it to the rest of the guys in the shop, they found it very useful as well.