How 3D would you say the flame effect is? It's marketed as 3D but I can't really tell. Also, does the fire appear in the middle of the logs in depth? hard for me to tell

I wish I could turn off my circuit breaker. But in our apartment all the breakers are locked in other rooms and nobody but the manager has access to and he never replies to messages. So going to have to do with just light switch off and hope for the best. Thank you for this.

He is not a fan of plastic, yet he has a plastic fan!

Do you have insert it into a fire place for it to be effective?

Your voltage detector made noise and lit up and you continued working on it?

Filastruder is impossible to find.

Is that an old Hunter fan ?

What kind of mesh?

that sounds like CRAP ! adjust the governor and belt !!!

I just bought one yesterday and need some parts

thanks for video its something I need to do.

I appreciated it. I had messed up the speed order last time I replaced the switch, and your wire color identification allowed me to put it back right this time. Thanks. (Incidentally, it is a 30 year old Hunter fan).

that was a prefect tutorial my friend evn though a few of my wires were a different color, it was pretty easy to figure out once the l wire was installed......once again thanks....

That straight line trick is 👌 thanks!

Nice video. Clear instructions that get to the point. Thanks very much

Great idea, just what I was looking for😊

I will definitely be giving this system a try this summer! Thank you!

You could’ve uncliped the light kit to make a easy installation

Love the idea of the screen. I was about to build one and drill many many drainage holes. But this will be much better. Thanks

Good and good 👍 👌 I love stove big in the cold 🌹 💐 🏵 ❤️ .

Please,please,please give me your phone# mine needs fixing!

Where you located?

What type of wood did you use ?

I just stumbled upon your video while looking to restore my family phonograph. Very well done! Thanks for all the helpful links! Wish me luck....🙂

Thank you for sharing. It was very helpful. I liked your video.

Thanks

Nice I like the idea of window screens. 😁

I just purchased this heater. It works perfectly, but the bail handle is too light gauge, and will not stay in place for lifting. You don't mention this in your review?

I just purchased this heater. It works perfectly, but the bail handle will not stay in place to allow carrying. It is too light gauge. You don't include this in your review?

I did too.

Neat, i have some cylenders, but nothing to play them on. i have the upgrade Flat disk cutter made from bell labs..

I am building this out of pieces of an old bamboo shoe rack. So easy

Looks great, and with a brighter bulb installed that’s all the light you need. kzbin.infoUgkxWF88GpljEn-0o34vtLFazEQ5h5Q33SjU As far as ease of installation- this was my first ceiling fan and it took about 3 hours because I had no idea what I was doing and also it’s helpful to have a second set of hands and a magnetic drill bit. Works great.

I know this is an older post and I'm not sure if you changed this setup... can you please tell us what the GPM and PSI rating for your pump? Also, are you running 12v or 110v?

How to turn off the spinning...tried to pull the string four times and the fan is not stopping

Very nice work. Thinking about doing this in my house and been researching ideas.

I had the same problem as OWILL1, I could not get the wire to lock in place of the new switch. I can not find a new switch with the wires already attached.

To much work of me, I bought a window Birds Choice platform feeder. Like number 5.

Its S1-S5 not 51-55 lol. Speed 1, Speed 2 etc..

Gord I can’t find a pedal sensor replacement. Wondering if you have a line on one? Thanks

I see below many people are complaining about not being able to insert wires into the switch. If you stripped the sheath from the old wire and you find that the wire is stranded type (not a thick single wire) then it will be difficult to push the wire into the switch because the stranded wire has no strength. You will have to coat the stranded wire with solder to bind them all together. Now the soldered end will have enough strength to be pushed into the switch.

My wires won't push in and I returned the switch and got another of the same kind for a 3-way ceiling fan. Don't the wires just slide into the holes on the switch?

Hi there, do the flames get washed out in bright artificial or natural light? I’ve read a couple of reviews of these classic flame units where people mention that

before i move into condo, there was one knob switch . one for fan and other for lights. lights are not attached to fan it separate. After i move in i noticed electrician change switch to flip only, which operates lights only and fan is no longer working or any power going in? how can i fix this? by buying new 2 or 3 way switch or something?

That was awesome! Thank you so much. You made it super simple.

Getting mixed messages from the manufacturer if I can create a frame wall and install this in it. I noticed the top of the unit gets VERY hot. Is this something you can install in a wood wall? If a frame is built and made out of shiplap can you put this unit inside it?

Can you relist on ebay? I'm willing to buy

Why don’t you read the Manuel to see what the controls & codes mean? I have the same unit. Like it very much. “Not a fan of plastic & styrofoam”, huh? Lol What do you expect them to pack it in to ensure safe & dry delivery? Hemp? Lol I’m not a fan of environmentalists, cuz they don’t live in the real world

Nice build.

Good build. Good channel too.