My name is Bill and we live in Lancaster CA. I have the same problem that you describe in the video. Can I send my circuit board to you and have you test and then replace the capacitor and flywheel diode. Obviously I will pay you to do that.

Beat solo sucks, is expensive and is a waste of Money, the sound quality is suck, money grabber, greed as fck, and this is not even easy to fix, its belongs to the bin. Suck as fck

My backlights don’t come on when I disconnect that cable. Do I replace my power supply board instead?

Nice Video! Clever Fix! I have no doubt that this would work on most DVD / Blu Ray / CD Players. Some combination of and / or variation of Clean Disc - Check / Replace HDMI Cable / System Reset seems to work in most cases. My late 90's / early 2000 Sony Discman and Philips portable CD players mostly responded to the 'clean the laser' fix. In my case: Sony Blu Ray Player (rack mounted), I did the 'Thirty Second Fix': (more like 3 Mins...) (You need to have either a can of compressed air, or portable mini-hand-blower, for this to work. I suspect that a hand vacuum with a (CLEAN) blower port would work as well) 1 Eject the current disc inside the player and leave DVD Tray OPEN 2 Unplug power and HDMI Cable 3 Take unit outside or into your garage 4 Make sure that the unit is secure (won't drop or fall) 5 Look on the underside, in my case (Sony 4K UHD Upscale) there was a series of 4-5 vents (presumably for air-flow or cooling.) Locate those vents and... 6 Alternate compressed / FORCED air through that series of vents, and occasionally through the OPEN DVD tray. 7 Do that for approx 30-45 secs. 8 Re-connect your device (HDMI & Power) to TV and test. REASONING: CLEAR OUT POSSIBLE / PROBABLE DUST CONTAMINATION INSIDE UNIT May be all that you need to do 👍 : - ]

Men what a great video!!! Thanks you so much that's the quality I was looking for in a video

I love you! It helped me to get my stuck button fixed!

I have the exact same tv, with the exact same problem!

Instead of using the popular "tape" fix which takes some guesswork can't a simple JIG with a flat ribbon cable and DIP SWITCHES be used instead? This will save applying and then moving the tape until the bad traces are found.

What type of led did you use?

I have a xbox One S digital edition that I put to work, but I opened and cleaned to maintenance found a liquid inside use alcohol 99.9% to clean and use as well compressed air, replace thermal paste, now the console doesn't turn on, just make one beep light on, in a second turn off. what you could recommend me to do.

The goddamn controller is DEAD... 'Nuff said! 👎

My Samsung 65" was sprayed indirectly with a cleaner by someone painting the house( it was mounted on the porch under roof. We immediately brought it down to dry it off. It won't boot up completely but looks like they squeezed the edge of the screen to hard because there is like a broken glass pattern in the right corner and the screen just faintly flashes.The back of the TV was dry so I am trying to determine if the power supply, main power board or the panel is bad? Help?

Well it doesn’t restart anymore but the lcd has no picture. Lights are on

And no update because its rubish

My X800MKII wont read most of the MP4 files. Sometime it reads fine but 9 of 10 times not

Great tutorial 👏🏽👏🏽!! I have one question, if the glass round lenses comes off the led light strip, do I glue it back on to the strip ? If so, what type of glue do I use ?

Mine was made in September 2005 so after almost 20 years. It just starting to have the issue where press power button. It turn off shortly after.took few tries to get it to turn on once it was works normal. One day have to get those capacitors. Old Electronics tell ya

I hope you or someone sees this that could help, so I done everything and I’m at the tape spot and I am 4 hours into this. I found a spot where it doesn’t boot loop but it doesn’t show color I had it happen one time but no matter what I do nothing works. I covered 1 pin 2 pins 3 pins in the 5 pin area that doesn’t boot loop with tape.

Firmware is quite big and should be in flash memory. Staying in bootloader means the last update deployment was unsuccessful and it has nowhere to jump. Usually, update process takes 2 steps. First, it downloads new firmware and stores it somewhere in flash memory. It should verify that the downloaded file matches online one. Probably using MD5 checksum. Second, it sets some flags saying update is ready to be deployed and reboots. Bootloader knows there’s update so it will deploy it by overwriting the old firmware (I heard about systems that use incremental firmware locations but never worked with them). At the end, it will clear update flags and reboot the system. After rebooting, bootloader will jump into a new firmware. The problem is, when deployment fails (can be many reasons actually) there’s no valid firmware. Your firmware is corrupted so your system will be scheduled for reset by watchdog. The only solution could be reprogramming your flash memory with proper firmware but I doubt you can do this without special tools and firmware itself(reddit)

Dude your instruction are so confusing lok

What an interesting, clear, and useful video! Thanks a lot!

Thanks for the video. all I had to do was press the first button lol

Just bought a DeWALT radio, love it, 😊thank you for this information 👍!!

gahhh! it worked!! ... I went from Vizio customer service telling me I needed to replace my TV this morning to it working again this afternoon. THANK YOU!

I purchased a used LG blue ray and when I put a disc in it just said check disk and then I did what you instructed and it works !!!!

Good how how can I get that Hdmi tester

Easy fix😂

Thank you very much … I Just finished fixing my QLED Q60A 50 inch, which I bought exactly 2 and 3 months before the on/off problem started …. I literally followed the video and made the exact same tape in the exact same place you put it and it’s working perfectly… before that I took it to a repair shop … I live in Germany… and the shop told me there is no hope for repair and that its the motherboard and he saw it several times in the same QLED Samsung… I was traveling the past 3 months … so I made this as a last hope before ordering a new tv… I was doing some digging the past couple of months since the problem started … and I found several similar people with the same exact problems like mine and every one said that the problem started exactly after the warranty have expired… it is really awful how can this happen unchecked… but anyway .. again can’t thank you enough.. you saved me 600€ for a new TV 🙏🏼🙏🏼

I have the same problem with my GU50TU8079 and partly fixed it. I taped up some pins and found out it's the first one all the way on the left (if you see it from the frame at 4:12 where it shows the connecter with the tape on). If I tape his one up, the boot loop is gone the backlight stays on, I can turn the TV on and off and I hear the starting sound and the sound of the tv programm, remote works if I press "home" so on.. However the screen stays dark :( Did anyone had the same issue? Is the first pin like a special pin or do I have like two seperate faulty pins? I hope someone can help. I'm close yet so far :D

Thank you! This video was so helpfull. Cheers

Just don't, send it out for reball repair, seen on ebay $65 plus shipping, you may damage board by baking, beyond repair and then you will need to buy another TV.

It fixed the boot loop, but my screen don't show anything

Good work my friend

Glue gun or special harden plastic glue???

My mom thanks you SO much for this!!

Tour phone requires NFC to be able to work- if your phone is capable of NFC, you'd know...since it'd most likelly have a "wallet" app already installed. Turn NFC feature on/off in settings....

While pressing and holding ZONE 2-CONTROL of the input selector on the main unit with the unit turned on, press the STANDBY/ON button , . "Clear" is displayed on the display, and the unit returns to the standby state. Do not remove the power cord until "Clear" disappears from the display.

메인보드 구매처 알수있을까요?

I know this is old but to buy TV 2 yrs ago and this happen is messed up! If I would of bought the 3yr extended warranty, that started After my 1 yr Samsung warranty I would of been able to just go trade it in for a new one! From now on it's worth $59.99 or even little more because so many of Walmart TV's screw up! I spent the day, then found the tape thing and worked it down to 3 pins or whatever you call them that hooks the 2 bottom panel boards together. I believe in Mexico where mine is made they pushed the plastic connector in to deep and messed up a few of them. Now i got a couple horizontal lines going across the screen but i can't hardly see them from my bed. I wonder if I could buy just that plastic cable somewhere? I don't know what it's even called, does anyone here? At least i got it from cutting on and off, and learned how to test and make sure it was not the power board. Thanks for the video

I have did the tape trick, the tv stays on but I still have no picture

Follow the instructions to troubleshoot same issue. I get audio from a streaming signal but no image whenever either ribbon cable is disconnected from each side of the screen. Backlight is ON all the time, but no image. Does this means a bad screen?

would you be able to add file type i can 3d print instead?

The easy fix in the title is a nice little bit of comedy there

so what if you don't have a single pc in your house to do the offline update

hi i have a problem it beeps but won't start i'm not smart enough to fix it so can i send it to you to fix it from finland

i’ve found some pins that do prevent the tv from continuously power cycling but the image is barely working. but that’s the best i can get… all other locations covered, the tv still just power cycles.

wow, very cool! thanks for sharing!!

Hero!!!!

WORKED, THANK YOU!!!