This worked for my HyperX cloud wireless as well... Thanks <3

i like this professtional version, but i can't find the version to support Ender 3 Neo Max , please tell me how can i download it

I made almost the same light today, but used 3 led strips on each side, connected one by one. Also I added a button to turn the light on and off, and powered all the light directly from the supply unit. I'm not sure how much power can the motherboard supply via that connector.

For 2024 is good ?

Could just depin it

Same here. No need to change rails or anything else. Another tip, it look even more perfect with presure advance setting in CP

СHC PRO from triangle labs more powerful! 2x time speed heating! Side fan only for PLA bat this printer more powerful to print simple plastics. I use this fan for heating camera to print ABS and complex composit plastics! If you hit camera to 60-65 C power printed items rise about 40%! Think 40%!!!! And you dasn't change pulley!!!!! Ho ho its MAST HAVE upgrade!!!!

hotend stl file ?

On all of my machines, none are inverted. Red is always positive.

Nothing here is worth the time it took to watch this. Certainly nothing worth doing to your printer.

is it ryzen 7 or 5 ?

Hi. Is it original LCD? What mods did you make? What firmware you use?

Interesting hack, but in typical fashion, there is no mention of some pitfalls of doing this without doing the math. You didn't say what voltage the board puts out, nor did you state the current capacity of the board. Cheap LEDs can work perfectly fine, but when you cut them down or apply higher than optimal voltage to them, they run hot, which means high acreage. This high amperage can damage your new printers main board. Be careful!

What acceleration do u used?

Is there any downside to installing a custom firmware?

I CANT BELIEVE THIS FKNG WORK, ty dude

I have a K1 Max and I'm having issues printing a good benchy with 95a TPU. It is all good, until the chimney. Then it gets bad and looks all melted and squiggly. I can figure it out. I challenge you to try it on yours. Let us know how it goes.

What if you had the diy inclosure what then?

Bro, are you still using it?

WHEN YOU PUT A BRAND NEW FILAMENT ROLL OF 1KG IT FLEXES THE POLY SHEET THAT HOLDS THE BLOWER FAN INSIDE AND WHEN IT FLEXES THE FAN POINTS AWAY FROM THE BED AT A 20* TO 30* DEGREE ANGLE WICH IS VERY HORRIBLE AND THE FAN IS USELESS BECAUSE THAT AIR IS DOING NOTHING SO I QUICKLY REMOVED THAT HORRIBLE SPOOL HOLDER WHEN I DISCOVERED THIS FAILED SPOOL HOLDER SO I ADVISE ALL OF YOU THAT NEED A SPOOL HOLDER TO GO WITH A TABLE TOP OR ONE THAT MOUNTS DIRECTLY TO THE PRINTERS FRAME TRUST ME YOU WILL THANK ME LATER. DO NOT USE THE ONE IN THE VIDEO I REAPEAT DO NOT USE THAT FAILED SPOOL HOLDER

You need to print out some 270° door hinges. I like the look of those covered side panels.

Can I use this for my 3S Plus

Ok question. Doing this mod then doing all metal hot end am I able to do pa6 cf? Or is the remaining Bowden tube still an issue for melting?

My ender 3 v2 neo is just stuck on the creality screen when trying to update to profesional firmware but when i try creality firmware it updates

Have you checked out K1 Max side Run Out sensor Plate on printables by smaug?

Hello, at one point you're not sure about the 24v, can you confirm that it's really that, it's important to know before buying the LED ribbon, thank you. And so that the light can be switched on and off as required, it's possible to put a switch near the front panel to turn it on only when we need it, while waiting for the firmware to take into account a LED bar when it's updated.

Can You share the config?

i been having some trobule with the latest firmware, i can´t calibrate the bed. Can you do a review?

I was searching for a solution for my direct drive extruder. Thanks for this!

Merhaba söylediginiz gibi site üzerinden ender 3 v2 neo yazıcım için bltuch olan yazılımı indirdim. Ama sd kart takınca crealty yazısında kalıyor yükleme yapmıyor. Anakartım 4.2.2. Crealty sitesi üzerinden orjinal son sürümü yükledim kurdu başarılı. Ama sizin gthup sitesinden yüklediğimi kuramıyorum isim değiştirdim yine olmadı. Lütfen yardımcı olurmusun bir haftadır bununla uğraşıyorum🙏🏻

Wow I did a different one but I could barely clear 5.5

Hi! Please help! I recently upgraded my Ender 5PLUS with a 4.2.7 32Bit motherboard and a colour LCD, of course i uploaded the best firmware ever, the Mriscoc 😅 My problem is, the firmware is locked at 230mm printing size, and i want to increase it to 370mm on what ender 5plus have. I tried to do it from slicer, but the printer firmware overrides the GCode and stops at 230mm. How can i increase the printing volume ?

Are there any updates on this firmware, as it works great

what if i donwload it and the picture is just pages?

Link light strip you used?

Needed this video, just grabbed a ender 3 V2 neo used last week that needed a new extruder, installed the micro swiss NG. These settings was all I needed. Gained a Sub!

Does the CR Laser module still work after this update?

I'm CONVINCED my model is SCRATCHING the bed plate during that initial "scrub" where it scrubs, then sits there while the temp is CHANGING. FF has HORRIBLE bed leveling FW inits, and I have visible scrapes in the back scrub line area as well as the back right corner in a T shape. It has already ruined ONE nozzle (while doing this during the initial printer setup brand new). How do they expect to "scrub" the nozzle on the back bed, at the start of the bed level calibration, WHEN IT HAS NEVER BEEN CALIBRATED (or after changing nozzles if things aren't quite the same or a new bed plate is put on that might be slightly thicker or smooth PC vs. powder coated). Seems like FF has some work to do there.

Same for me, did Factory Reset updated firmware, rooted again and reinstalled mainsail again, did inputshaping in klipper , sliced with creality Print 5 and boom ringing gone, do Not unterstand it but i‘m happy 😊

You should, if not done already, switch to klipper. It is by far the best upgrade I’ve done to mine. If you have Rpi laying around , that’s really fast to set up.

Would this work on the Ender 3 Neo (V1)

Still have this hardware sir? Can you tell me, probe setting for this.. because my hardware setting gone.

no way slamming the mic against a table few times actually worked

Hey, this seems like about 40mm/s, sure not 150mm/s maybe you have limited accelerations. To achieve these speeds , acceleration should be above 2000mm/s^2

Didnt showing loading screen when updating touch pad

Hi, great video. Just bought the Ender 3 V2 Neo on sale for my kid (24 years old, jajaja), and also live in Mexico. I see you have made lots of upgrades for this printer. I want to ask you, in your experience with this printer, what you think about it and witch you feel are a must-upgrades to do.

Gonna try this out on my next print. Thanks for the video!

Hi, can you share what fan connectors did you use? I want to buy them but idk which

Sweet thank you! It goes on the opposite side no issue as well!

It’s in the description