5 ай бұрын
5 ай бұрын
7 ай бұрын
11 ай бұрын
Жыл бұрын
Пікірлер
@AdrianGtz 22 сағат бұрын
What tires do you have on it?
@robbsgarage 22 сағат бұрын
@@AdrianGtz Nitto Ridge Grappler 265/50/R20. I love the way they look on it, and they handle pretty good in dirt, rock, and snow.
@MatthewFlint-v3p Күн бұрын
My 2024 GMC sits for weeks at a time. Do you think this will draw my battery down if I don’t drive it often? Definitely don’t want to connect and disconnect every time my truck sits.
@robbsgarage Күн бұрын
@@MatthewFlint-v3p you may want to contact Range Technologies directly to confirm, but I don’t believe this module draws any power whatsoever.
@MatthewFlint-v3p Күн бұрын
@ I appreciate the response, will do. Thanks
@TheCarCrazyGuy 4 күн бұрын
I hate to be the bearer of bad news, but that device will not prevent lifter failure. If you want to prevent lifter failure, you need to have your engine deleted of all that hardware and a tune installed so it doesn’t look for it. I just recently sold my 2022 Silverado 1500 refresh with the 6.2L engine. Although I didn’t have any problems with it because I really didn’t drive it much. I’m sure eventually I would. I currently own a 2024 Silverado 2500 diesel. None of that nonsense is on my truck however, all that emissions crap is on there so unfortunately there’s no way to get around this stuff.
@robbsgarage 2 күн бұрын
@TheCarCrazyGuy I have my doubts as well, but am subjecting this truck to this test specifically to see if the module will help prolong the lifters or not. I’ll be posting updates every 25K miles (or until I experience a failure), so we’ll see…
@infirmux 7 күн бұрын
"notify your card issuer that you'll be travelling abroad" - yo, what now? Must be a US thing :D
@robbsgarage 7 күн бұрын
@@infirmux yeah, it’s a US thing to prevent fraud by restricting international transactions; however, getting less prevalent now with tap/chip technology and with card issuers coming up with more ingenious analytics to spot fraud.
@TimCox-u4x 10 күн бұрын
I installed the same device on my ‘24 GMC Sierra and have been pleased with the results. GM should consider removing DFM all together but glad Range offers a solid solution.
@robbsgarage 9 күн бұрын
I agree!
@jjung2005 11 күн бұрын
Thanks for the video! Has your fuel consumption gone down since the install? So, this device will keep all 8 cylinders running all the time?
@robbsgarage 11 күн бұрын
You’re welcome. Yes, this keeps all cylinders firing by disabling DFM but it doesn’t disable “0 cylinder mode” whereby fuel delivery shuts off when coasting at low speeds (which I don’t experience very often). I’ve now had the truck for 6K miles-first 3K without and last 3K with the module. Haven’t really noticed any difference in fuel consumption (good or bad), but it could be because I babied the engine during break in period and have been running it much harder the last 3K especially after installing a proper exhaust. So, theoretically if I drove it the same before and after I might get better mileage with the module but can’t say for sure.
@CSHOPSHOP 12 күн бұрын
your intro blew my ears out LOL
@CSHOPSHOP 12 күн бұрын
your intro blew my ears out. LOL
@BigSexysHouse 13 күн бұрын
I’m waiting for decent weather to install the same product on my ‘24 Denali Ultimate. Also have a pending install for the Borla Atak when it arrives. Can’t wait!
@Thatairlinepilotguy 15 күн бұрын
@robbsgarage what exhaust do you have on your ‘24??
@robbsgarage 15 күн бұрын
@@Thatairlinepilotguy AFE 0FG-I spent a lot of time researching catback exhaust sounds before buying this one and felt it produced the best sound available.
@Thatairlinepilotguy 15 күн бұрын
@ great to hear! Exactly what I’m getting ready to put on my ‘24 6.2 trailboss. Installing the range DFM tomorrow when the unit arrives. Your video helped a lot, thanks!
@robbsgarage 15 күн бұрын
@ I should have made a video about the exhaust mod. Install itself wasn’t so difficult, but removing the stock pipe wasn’t as easy as you’d think. 6.2 may be different, but the 5.3 pipe is very long with several bends that had to snake out the rear. American Truck produced a video that makes it look simple, but it is not. I eventually gave up and cut the pipe out.
@Thatairlinepilotguy 15 күн бұрын
@ good to know. A buddy of mine owns a body shop, so we’ll throw it up on the lift and install at his place. Shouldn’t be too hateful for us.
@BR549_o7 10 күн бұрын
@@robbsgarage "AWE 0FG" out of Pennsylvania...
@monettevarela584 17 күн бұрын
Thank you Robb!!! This worked like a charm! Unfortunately I had the RR towed prior to seeing your video but nevertheless thank you for posting this, cotter pin worked great!!!
@robbsgarage 17 күн бұрын
Sorry you had to tow, but happy to hear you fixed it! Be sure to subscribe for more RR info in the future.
@smartassandy 21 күн бұрын
Just happened to me and the tow guy said he towed another RR the night before for the same thing, This worked like a charm thank you so much. For what they charge for these cars it is disgraceful how cheap some of the parts are
@robbsgarage 21 күн бұрын
@@smartassandy sorry to hear, but so happy to know this trick worked for you!
@AmandaMama-wx5gh 21 күн бұрын
Congrats! 🎉
@edgardohernandez7248 24 күн бұрын
How I have to do to put the car on auto lift Do you have any tip to protect the air bags suspension
@robbsgarage 24 күн бұрын
@@edgardohernandez7248 sorry but I haven’t had to put this on a 2 post lift yet so I don’t have any advice to share.
@landenpratherart 26 күн бұрын
Thank you! You saved us a HUGE tow and service bill!
@robbsgarage 25 күн бұрын
You’re welcome!
@yassinediallo431 27 күн бұрын
Youre the man Rob!!! I Was stock in a snowstorm on christmeas eves hating my life. That video is a real gift to any range rover owner. Thanks again
@davidl7672 27 күн бұрын
lol! so my kid just called me, he was stuck in the middle of the street, he just pulled out of the driveway. well, your video saved me a ton of hassle. I can't thank you enough. I didn't have a cotter pin, but i did manufacture something out of a hardwood flooring staple. I got the car moving again after we pushed it back in the driveway...i also didn't know about the lever under the cupholders, so that was also awesome to learn. thank you!!!! Found someone on amazon that makes these out of aluminum, so that might be a forever solution.
@robbsgarage 27 күн бұрын
@@davidl7672 fantastic! Glad my bad experience can help so many others.
@Everything-k3y 28 күн бұрын
Range does say coasting foot of the gas does use the collapsible lifters to go into zero cylinder mode, however it’s not Dfm. Dfm also uses the collapsible lifters. Both modes share the same hardware, the collapsible lifters.
@robbsgarage 28 күн бұрын
@@Everything-k3y here’s what Range told me: “The engine will still enter 0-cylinder mode while coasting at slower speeds. Contrary to what many think, this is not a DFM function. It’s actually the engine shutting off fueling, so the cylinders don’t actually fire. It’s not the DFM system turning on and collapsing lifters to prevent the combustion cycle.”
@Everything-k3y 27 күн бұрын
Correct, that’s exactly what they told me, zero cylinder coasting does not use the Dfm program but it does use the collapsible lifters to keep the valves closed in zero cylinder mode.
@WRCWRX 28 күн бұрын
O2 sensor socket with a good offset works great for the upper nuts on the motor mounts.
@robbsgarage 28 күн бұрын
Nice, thanks for the tip!
@jongwoo 28 күн бұрын
I was seriously thinking about trading in my GX for this.
@robbsgarage 28 күн бұрын
@@jongwoo do it!
@jongwoo 28 күн бұрын
@@robbsgarage checking measurements on the bed for my splitter and height for my garage at work. lol
@robbsgarage 28 күн бұрын
Did you hear how good the exhaust sounded at Buttonwillow? Factory exhaust is too quiet, now it roars!
@jongwoo 27 күн бұрын
@@robbsgarage I don't remember it... you should have rev-ed it when you drive by
@mattmccams Ай бұрын
MPVI3 and some credits and this problems solved
@chrism1157 Ай бұрын
When I bought my 2022 RST Z71 5.3, it was when they determined AFM finally had to go. My truck came from the factory without AFM or DFM. I'm happy I don't have any of it. Everyone i know with a 5.3 has had lifter issues or needed a full motor replacement. The failure rate is way higher than GM states publicly.
@robbsgarage Ай бұрын
@@chrism1157 I’m so jealous! You bought at the right time.
@MattJones1829 Ай бұрын
The 2021 and 2022 models had a run during the hear of the infamous "chip shortage" where some of the V8s didn't have a functioning AFM or DFM system. So yea...no DFM issues. But not so fast...the DFM would not function because of electronic/tech reasons. But unfortunately those miserable AFM or DFM lifters are still in the engine. So while they don't function as designed, they are still present. Perhaps the lifters not constantly collapsing, reactivating, etc. will help prolong the life of these crummy lifters............................or maybe not. Time will tell but one thing for sure, you folks get a much better quality driving experience and for "free!"
@excelerater Ай бұрын
These pricks are killing the V8...This is why I wont buy a new truck..Keep it,it does not save shit and I am paying for 8 cyls and I want them 24/7
@robbsgarage Ай бұрын
Amen brother, these auto manufactures and the EPA are killing the industry. I wouldn’t have bought a new truck if I didn’t need one. Hope to keep this one forever because I can only imagine how much worse it’s going to be 10 years from now. I got this DFM Disabler to help make this motor last as long as possible!
@markfrench3665 2 күн бұрын
I have a 2013 Sub LTZ 5.3 with 187k. Had the Range product since 40k miles and never had any issues. Motor runs like a champ giving to my son. Just bought a 24 Sub HC with a 6.2 and will put this on when it arrives.
@robbsgarage 2 күн бұрын
@@markfrench3665 great to hear you’ve had good experience with these things. I’m hoping this module prolongs the motor life. So far so good, and I’ll keep posting updates along the way.
@jloutz Ай бұрын
Oh, hell no not doing this to my new Silverado 1500 RST.
@BR549_o7 9 күн бұрын
why not?
@nachig4336 Ай бұрын
Can you suggest a local coolant for Velar 2019, I-4 ? Is Dex-cool orange compatible with the car ?
@ederromero289 Ай бұрын
One thing I noticed is the oil pressure goes up when you accelerate and decrease when you start breaking. I thought it would stay at a constant rate.
@BR549_o7 10 күн бұрын
its called RPM. higher rpm - more oil pressure. This happens even with v8's from the 60's era. Normal operation
@ThePlotts Ай бұрын
I wish they would have left it as an OBD plug in.
@robbsgarage Ай бұрын
@@ThePlotts I thought the same at first, but once I installed it I actually prefer this better-only takes 10 minutes and doesn’t clog up the OBD plug area.
@BR549_o7 10 күн бұрын
why? the OBD port one drains the battery I hear. This newer one does not drain the battery.
@MyCCW 6 күн бұрын
With the 2022.5 refresh that extends to the 2025 MY, GM changed some things electrically so they had to completely redesign and re-engineer as their product could no longer do its job through the OBD port...
@JP-ec8fe Ай бұрын
Man everytime I get in my f150 since buying new in 2017 I push that stupid auto start button. Curious - is the DFM system still active even with tow/haul mode on?
@robbsgarage Ай бұрын
@@JP-ec8fe nope! This thing disables it at all times including that stupid auto start!
@louismartinshaombouwe7523 Ай бұрын
You are the best ❤❤❤
@IrvingNolasco Ай бұрын
Thank you so much brother saved me 🙌🏻🙌🏻🙌🏻🙌🏻🫡🫡🫡
@robbsgarage Ай бұрын
@@IrvingNolasco great!!!
@Haribo_UK Ай бұрын
Great vlog looks amazing
@damianpasour Ай бұрын
Nice looking Range Rover I’ve always wanted one of these 😊
@T13RA Ай бұрын
Hey Rob, Where’s your shop?
@JP-ec8fe Ай бұрын
Nice work! My first thought in the intro was “that’s not the inside of the Rover” then boom….new rig alert!
@robbsgarage Ай бұрын
Haha, yeah new truck in the garage bro! Just installed my Christmas present on it-“Zero F**** Given” catback exhaust.
@AutomaticProductions Ай бұрын
nice driving, Ill see ya next season!
@Ricky50scJustalil6cylinder Ай бұрын
Great video man thanks
@robbsgarage Ай бұрын
You’re welcome, hope it helped!
@ddallgood1383 Ай бұрын
Excellent video! Pump out first, then remove the drain plug, and show the amount missed by pumping, which would be interesting to know. Less messy. Also, anything that could be done to determine the electronic oil level accuracy would be great. Im sceptical it reads in even 1/2 quart intervals.
@robbsgarage Ай бұрын
Thanks! Planning on making that video with my next oil change. Just finished replacing the motor mounts today so about to publish that video which is promised to be the most comprehensive on the subject.
@ddallgood1383 Ай бұрын
@@robbsgarage looking forward to that.🙂
@joe_ferreira 2 ай бұрын
5k for one rear quarter panel seems crazy to me You could have bought the entire hgk euro fighter kit for around that.
@robbsgarage Ай бұрын
Yes, it was ridiculous. Wish I could have cut one out from a donor car but body shop said it wouldn’t have maintained structural integrity. I don’t know… but, at least the finished product turned out excellent.
@williammcneal3471 2 ай бұрын
Great video. What is your cargo box lift system. Looks easy to use.
@robbsgarage 2 ай бұрын
@@williammcneal3471 thank you, hope it helped. It’s a Thule system. Can’t remember the actual model number, but it’s designed for use with most Thule cargo boxes.
@danielnoggle7949 2 ай бұрын
Had this same coolant leak on a 2010 Mini Cooper S! Thank you so much for the video!!
@robbsgarage 2 ай бұрын
Glad it helped!
@osman_wants_speed 2 ай бұрын
nice video. thank you. how long does it take the put these camber plates on?
@robbsgarage 2 ай бұрын
I’d estimate 1-2 hours per side depending on your level of experience. Let me know after doing it if you found the video to be of any help.
@GeorgeCreasy-rl9lc 2 ай бұрын
Just saved me £700 for a new radiator. Thank you
@robbsgarage 2 ай бұрын
Yesss!!! Congrats.
@orangefishy-original 2 ай бұрын
Mine won’t work
@MrAzulikit 2 ай бұрын
What did you pay?
@joe_ferreira 2 ай бұрын
You should create a playlist for the rebuild. Thanks for the videos
@robbsgarage 2 ай бұрын
Done! Great idea, thanks for sharing.
@joe_ferreira 2 ай бұрын
@@robbsgaragethanks! I have saved it so I will get notifications when new videos are added. Also subbed. 😀
@robbsgarage Ай бұрын
@@joe_ferreirathank you!!!
@richardlove1420 2 ай бұрын
Where do you get a cotter pin from?
@robbsgarage 2 ай бұрын
Any hardware store will sell them. If you’re located in the US, you can buy them individually at Ace or True Value; whereas Lowes and Home Depot will likely make you buy a boxful.
@jacksonbell325 3 ай бұрын
Great video! I'm having trouble finding the replacement (rivet?) for the cross bar that adds support to the box - the cross bar that you used to get some leverage to put force on the lid lifter. Any help?
@robbsgarage 3 ай бұрын
@@jacksonbell325 try etrailer.com and see if they sell it.
@lean71841 3 ай бұрын
It's pronounced Tooly
@robbsgarage 3 ай бұрын
@@lean71841 I had no idea! Thanks for informing me.
@lean71841 3 ай бұрын
@@robbsgarage No problem, great video by the way. There really is little information on these lift arms.
@angiebarthol1431 3 ай бұрын
Amazing! Thank you!
@robbsgarage 3 ай бұрын
@@angiebarthol1431 you’re welcome!
@Marzee_theCreatør 3 ай бұрын
You didn't actually show me how you disconnected the hose 😅to put the o ring on 😑
@robbsgarage 3 ай бұрын
On my car it just pulled straight out but one of the viewers said there’s a clip that squeezes on his. Will come off fairly easily if the o-ring is broken, should press on very tight with a new o-ring of the proper size. Check out my update video for a better size I subsequently installed.