Very helpful. Thank you for taking the time to record and add any adjustments you would have made along the way.

Make sure you use the emergency break because when you pull the sway bar links it could roll away on you.

cool :)

Great job! This video really helped and I was able to do it successfully. Thank you.

How many trips to Lowe’s did it take lol

😊

Solid video, thanks Bro. Question, I do a lot of driving. Sensor went dead 3 days ago, fluids are good. Was hoping to change out this weekend. Would that cause more problems?

Nice job you are a real shade tree mechanic moog looked sketchy to me but you cleared that up thank you for the video

Clean work man, great job!

Thank you! Exactly what I needed. Trying to surprise my bf with some LED headlights and couldn’t figure that side out 😅

Thanks i was trying to find a video to see if i needed to remove the tires 💪🏽

Thank you. Straight to the point.

Bro you literally showed the sensor hole with the filter inside it after you removed the sensor. At the very least you need to take that old filter out and clean it well and then put it back in if you didn't buy a new one.

It looks to me like the long baffle on your air intake is cracked. At 3:44

How do you get around that damn plastic shield in front of the sensor?

🎉 thank you 🎉 I always turn the ignition to the on position but not start pump the gas three times turn it off and start it does the same thing. But I like your method it’s a lot easier.

This proved to me more awkward than trying to undress a lady in a triumph spitfire with the roof on, and not nearly as rewarding, but we got're done.

Thanks for the help , got done in about 10 minutes ! It sure beats all the other BS I saw on youtube !

You’re a life savor! Thanks love!

Thanks bro appreciate it man

@ 6:11 the black plastic you can see in the bottom of the hole IS the screen that you said you were not able to see. Most folks use a small pick to hook into it and pull it out, but I took a tip from another video and used a 1/4" coarse thread lag bolt about 4" long and screwed it into the plastic with my fingers only, then pulled it out. That worked well but I hear the pick works easily too...just didn't have one handy. People say that screen can get clogged preventing the oil from getting to the pressure switch. Other than that I did it the same way as shown here except I couldn't get the special 1 1/16th" sensor socket to go down onto the hex part of the sensor so I ended up using a regular 1 1/16" (6 point) deep well socket and it went on pretty easily. Both sockets fit fine with the part removed. I think that plastic cover was hitting the side of the socket and my regular deep well socket was probably a little thinner walled. Once it was done I still had low pressure that fluctuated when I hit the gas from about 15-35lbs. I'm wondering if I should have poked something down in that hole to clear any possible sludge out, or if I should drop the pan and check the feeder tube O ring. I've heard that is also a common cause as well as the oil pump or possibly wrong oil and/or filter. I'm not a mechanic and not looking forward to the O ring or especially the pump. If anyone knows if you can replace the pump through the bottom of the timing cover after the pan is off (without removing the timing cover), I'd be interested in any tips. I heard someone imply that it was possible, but they didn't elaborate.

Great instructional video. Passenger side bulb successfully changed. Being a 2007 model year (now 16 yrs old) the bottom part of the airbox took a little elbow grease to jar it loose. Thank you 'thatoneguyfrom87'. Well done.

Why would they do this to their customers?? Complete BS.

Nice video. I’ve got to do my 2007 Chevy tomorrow.

Thanks did a good job

Thank you man...

When my heater/a.c blower stops working, I usually smack the blower itself and it works as new 😂

Great Video Thank you for sharing.

6:05 THAT IS THE FILTER RIGHT THERE!! you got to get it out with something like pick or pliers.

Where did you jack up the car

I think you did a great job

I changed visor lights too, it’s the hardest to do imo

Am I the only one getting a kick out of how this guy talks? I’m fn dying over here. Good video and idk man but this shit had me rolling 🤣🤣🤣🤣.

Good job

What issues did you have to make you change it 😊

thanks for the video it helped a lot

Curious. Did you have to replace the screen.😂😂

We have the same truck ... Being broke right now so I'm trying to fix it myself. Wish me luck 🤞 thanks for the video, helped with the spark plugs!

Good video thanks

The best bro!!! Thank you so much!!!

Thanks. BTW, plug torque is 20 ft-lbs.

Thanks for the help brotha...

Hell yea brother thank you 🙏🏽

Thank you for the vid, I’m doing the same job tomorrow

I appreciate this video, I am planning on doing this soon.

Great video Man! You did a nice side attempt..(mean while shops are removing half the motor to get access) Great Job 👍💯

Great! How long did he take you the whole process, please?

Where can i find that sway bar bushing bracket? i need one of those

If you have big hands, this job is a nightmare. Pro tip: DO NOT BUY a CHEAP SENSOR from AMAZON. They break and you'll have to go to Autozone and get another one anyway.

Dudes Voice is all over lol