7 ай бұрын
7 ай бұрын
7 ай бұрын
7 ай бұрын
7 ай бұрын
8 ай бұрын
11 ай бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
2 жыл бұрын
2 жыл бұрын
4 жыл бұрын
6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
9 жыл бұрын
Пікірлер
@jgarrison6526 2 ай бұрын
What oil do you recommend?
@OceanBreeze2022. 2 ай бұрын
Do the pioneer 1000 have the same issues? Thanks
@cryoheatmetaltreatment3025 2 ай бұрын
Yes, unfortunately they do.
@jsimm4587 5 ай бұрын
Just put your foot on the brake and stop before you yank it into high gear . All you need to know . You can also grind the dog catches right back too .
@davehoward3645 7 ай бұрын
How much for total rebuild inside case?
@cryoheatmetaltreatment3025 7 ай бұрын
Please contact: cryoheat.com 760-231-1394
@marcleblanc3602 9 ай бұрын
Looks cool, not my problem, I hope.... the hi was difficult to engage, often grinding on half position till pushed. Now the low left engagement, so ajusted the rods, but the hi seems on low speed.... didnt push it yet.
@cryoheatmetaltreatment3025 9 ай бұрын
Contact CryoHeat and ask for Josh. He can help you with what could be your problem with your machine.
@fomocowboy 10 ай бұрын
How do you disassemble the final drive? There's a washer on the end that I can't figure out how it comes off
@danielgarvin8615 11 ай бұрын
Ate the dogs off the high gear last summer, rebuilt the transmission and added the cryo heat shim. One year later, no high range again.
@cryoheatmetaltreatment3025 11 ай бұрын
The dogs are blowing off the gears, because of one or two reasons. Shifting into gear when the transmission is still moving. shift linkage or shifter out of alignment, or got bumped. This sometimes can happen in a really bad G out. The high speed gear shim is not a device to keep the dogs from blowing out, (most of the time that’s operator error.) the high speed gear shim replaces the snap ring that is not designed for a side load. Our shim gets rid of the snap ring failure issue.
@danielgarvin8615 11 ай бұрын
@@cryoheatmetaltreatment3025 okay. Well, my shift linkage was adjusted correctly after the transmission was re installed, and I never move the shifter while the vehicle is moving. So I'm not sure what's going on. It had issues popping out of gear even right after repair. Maybe something linkage wise inside the transmission is bent or something?
@armedfarm3429 Жыл бұрын
I see way too many people using a heavy gear oil in these splash lubricated transaxles. So it's too thick to splash around in the case these parts wear out, esp. the side load shaft bearings & thrust washers & snap rings that hold them together. Use nothing heavier than a 5w-20 or JD hy-gard low -vis, or AGL. No more 80-90, or 75-90. 75w would be ok, remember oil in splash systems has to be thin like most all trans/diff/axels.
@happydayz5321 Жыл бұрын
Correct..........Just use AGL and forget about it. Stop trying to be cute and saving a nickel.
@Hastings_Racing Жыл бұрын
Just threw some bearings in my turbo s thanks for making a good kit
@N-Lee Жыл бұрын
Why? Nitrogen?
@ME-pb2gf Жыл бұрын
What a crock. Now you will just shove the bearing into and possibly through whatever pocket it's sitting in.
@joshlahaye1102 Жыл бұрын
No, I’m sorry that you’re wrong. The bearing is already being sideloaded from the entire shaft into the bearing race. This high-speed gear shim has never failed, or has the adjacent parts that it is working with. also, the inner bearing race is getting the exact same amount of load without the shim However, the shim replaces the snap ring that is 100% not designed for a side load. When giving a snap ring, significant sideload, it will slide out of the snap, ring groove and cause failure to the high gear. If you have any questions about engineering or metallurgy regarding CryoHeat products or services feel free to contact our engineering staff.
@joemartinez3613 Жыл бұрын
How much for one of ur transmissions, mine blew right side bearing and housing
@DontComeToMyHouse Жыл бұрын
I hear about some folks putting 75W-90 gear oil in the sub-trans and it runs a lot better. Thoughts?
@Nickvanscandal Жыл бұрын
I've heard that too, but haven't had any first hand experience
@stgraves260 Жыл бұрын
So are yall going to do a gear reduction as well ?
@dsadosomthingawesome5386 Жыл бұрын
they should create parts that dont cost more than the whole machine new
@Bars_on_wheels Жыл бұрын
Hello yall.. how can i do a warranty claim with honda having those issues help pls
@horaceboone2817 Жыл бұрын
𝐩𝓻Ỗ𝓂Ø𝓈Ｍ 🤤
@ryankeplinger6226 2 жыл бұрын
How much would it cost to have the stuff you have done to this talon trans done to mine?
@cryoheatmetaltreatment3025 2 жыл бұрын
Hi Ryan, go to cryoheat.com and select UTV/SXS then go to Honda. From there select Honda sub transmissions, then sub transmission parts and services. If you need any more help please call us at 760-231-1394 or email [email protected] 👍🏼
@mikebrown41182 2 жыл бұрын
Is it safe to cryoheat lets say akadize products like Hinson clutch?
@cryoheatmetaltreatment3025 2 жыл бұрын
Absolutely it is. We process Motercycle clutches all the time. Outer basket, inner basket, Pressure plate, springs and all of the fiber and friction plates. It makes a huge difference
@tigwelding123 2 жыл бұрын
💪👍💯
@shawnthomas1603 2 жыл бұрын
Hey where are you guys located..
@cryoheatmetaltreatment3025 2 жыл бұрын
2913 Oceanside Blvd. suite B Oceanside, CA 92054
@aw9680 2 жыл бұрын
You guys should create a dog selector that has 6 dogs on each side. 6 to drive low and 6 to drive reverse.
@drmarkintexas-400 2 жыл бұрын
🏆🏆🏆👍🇺🇲🙏 Thank you for sharing.
@aw9680 2 жыл бұрын
Would you call this "bulletproof" now?
@cryoheatmetaltreatment3025 2 жыл бұрын
Yes. By a long shot this is way better than stock !
@isaiahpropps6578 2 жыл бұрын
First here
@clodnut 2 жыл бұрын
I wanted to buy that shim, but it's not listed on your site
@cryoheatmetaltreatment3025 2 жыл бұрын
Go to cryoheat.com, select UTV-SXS, then choose the icon for Polaris 👍🏼
@clodnut 2 жыл бұрын
@@cryoheatmetaltreatment3025 will that work for a 2001 scrambler?
@clodnut 2 жыл бұрын
@@cryoheatmetaltreatment3025 scrambler 500 sorry. I'm not seeing my model bike on your website
@SavageBunny1 2 жыл бұрын
So basically the only things that will survive a nuclear war is these brakes and the cockroaches lol
@wicked.mainah5994 2 жыл бұрын
Would this cause the transmission to make a clunk on take off in high gear only?
@cryoheatmetaltreatment3025 11 ай бұрын
No, this would not make a clunk on takeoff whatsoever. The high speed gear shim is a device to only eliminate catastrophic failure due to snap ring failure because they are not designed to be sideloaded. By installing the high speed gear shim, the snap ring is no longer needed.
@ritchie709 2 жыл бұрын
What does it sound like when this is happening?
@cryoheatmetaltreatment3025 11 ай бұрын
Garbage disposal with silverware in it
@americanlawdawg3609 2 жыл бұрын
Bullet proof that sumbitch! Don’t forget to stud the heads with ARP! 🇺🇸
@glennbrown8213 3 жыл бұрын
Is this for the 2018 850 highlifter
@tbirdage 3 жыл бұрын
No reverse chain upgrade?
@120dn122 3 жыл бұрын
I have a noise between acceleration and deceleration which sounds like play in the trans. After seeing this video I have an idea this might be related to this problem? Would it sound like “crunching” when letting off the accelerator if the high speed gear had movement from side to side from a bad snap ring?
@cryoheatmetaltreatment3025 11 ай бұрын
Possibly however, you wouldn’t be able to go much further in high gear because eventually they would be a catastrophic failure. The crunching that you hear may be a bearing getting ready to let go. We highly recommend you addressing this issue and fixing it before it could cost you thousands more in damaged parts.
@riotwarrior 3 жыл бұрын
Hey. I just blew hi gear and feel it's same issue as shown here...can you tell me more about this shim you have?
@cryoheatmetaltreatment3025 11 ай бұрын
cryoheat.com/collections/turbos-hispeed-gear-shim/products/polaris-xp-rzr-high-speed-gear-shim-br-ch1002
@andrewz7441 3 жыл бұрын
Will this shim work in a 2017 Polaris XP 1000 EPS?
@cryoheatmetaltreatment3025 3 жыл бұрын
yes. It will fit all RZRs from 570, 900, 1000, Turbo and Proxp
@neilkaye081 3 жыл бұрын
I emailed Presion concepts twice about getting my suspension work done they never even responded
@bird4dbk420 3 жыл бұрын
Try calling them (951) 697-8488 👍🏼
@fitnessathome92 4 жыл бұрын
I want to learn more . And I want to work with you sir . 😊😊
@Willie_MN 4 жыл бұрын
Where does the "heat" part come in?
@JonesCrew576 4 жыл бұрын
Love what your doing for all things desert, gotta keep this industry alive!
@drjhunter 4 жыл бұрын
When is can am going to put a DCT in the maverick x3?
@hopehacker9536 5 жыл бұрын
He is my family friend! I am famous
@hopehacker9536 5 жыл бұрын
It is Hope!
@hopehacker9536 5 жыл бұрын
Hi
@Stryker882 5 жыл бұрын
Do you sell these transmissions or would I have to send mine in to have it rebuilt?
@cryoheatmetaltreatment3025 5 жыл бұрын
The choice is yours! We can order a new transmission for you or you can send in the one you already have. 👍🏼 Feel free to check out our website www.cryoheat.com or you can call us at 619-940-4227 with any questions you may have
@rememberussliberty1822 5 жыл бұрын
Is that a random ar15 barrel?
@SSMaynerd 5 жыл бұрын
that's an axle shaft
@florianschwarz8811 6 жыл бұрын
top notch!
7 жыл бұрын
Has anyone out there had you're suspension revolved by them, and did it help?
@rookiefmxrider 5 жыл бұрын
Hell yeah it help's
@cryoheatmetaltreatment3025 9 жыл бұрын
CryoHeat Treated knifes hold a sharper more than 3 times edge longer.