K M Workshop

Пікірлер

@rustandoil Күн бұрын

I like a bit of Oak.... Nice job 👍🏼

@rustandoil Күн бұрын

Stand alone diesel heater is a bloody good idea! Can't help you've missed a trick not welding a few "tie-downs" in the rear body frame. And I'm a bit concerned that there won't be much thread in the tapped holes in the box section 🤔

@rustandoil Күн бұрын

I've watched plenty of Land Rover builds.... It's great to see someone doing something a bit different.... Purpose built as a working vehicle 😎

@rustandoil Күн бұрын

You're doing a nice job on this.... Certainly chucking lots of new parts at it! 😂 On my 110 there's a spreader plate that goes on the inside under the bolt heads, it's not thick enough to cater for the over long bolts though

@rustandoil 2 күн бұрын

Part one?.....you should have invited us along earlier 😉

@paulsharp1679 2 күн бұрын

I have a 606 in my landrover, things you need to watch, change the Glow plugs, whilst you have the inlet manifold off, pin the front crank pulley, my key sheared, took out the internal bore of the pulley, and lastly look to increase the water volume of your cooling system, these engines run hot when running hard 👍. Superb content

@rustandoil 2 күн бұрын

Nice job 👍🏼

@KeetonMarine 2 күн бұрын

Thanks! 👍

@rustandoil 2 күн бұрын

@KeetonMarine I landed here coz the KZbin algorithm.... I'll go and watch the rest in your Defender build series over the next couple of days or so 😉

@judzantn 4 күн бұрын

Hi,I would like to ask if its a good idea to use the automatic mercedes gearbox when doing these conversion?

@judzantn 4 күн бұрын

Hi,I would like to ask if its a good idea to use the automatic mercedes gearbox when doing these conversion?

@KeetonMarine 3 күн бұрын

I wanted manual because we do a lot of towing, the issue with using the Mercedes transmission is we would need to run an TCU to control the gearbox and then a divorced transfer box. We may use a ZF auto in a future build there are stand alone tcu's available for these. Thanks

@michaelfraser5723 4 күн бұрын

Old man near me used to put a Ford Transit engine in everything he owned, the 'banana' one, because the timing belt was easy to replace and they used to be cheap. Your choice opens up new possibilities.

@KeetonMarine 3 күн бұрын

Thanks we turbo'd a few transit di engines they were a strong unit.

@michaelfraser5723 4 күн бұрын

Did you replace the rear crank seal ?

@KeetonMarine 3 күн бұрын

I haven't replaced the rear main it was dry and I'm going to fit an r380 stumpy later this year so I'm planning on doing it then, Thanks

@rentalift3625 5 күн бұрын

where can i get a om606 engine

@joeedwards627 4 күн бұрын

Pet shop?

@KeetonMarine 3 күн бұрын

I bought a complete car, Mercedes E300td (W210) I could drive the car test the engine then sell all the parts I didn't need, I thought this was the best option for me, Thanks

@ilbelvaramirez3495 6 күн бұрын

r380, change for a zf please

@KeetonMarine 3 күн бұрын

We might go ZF route on our next build 👍

@tuningemporium 6 күн бұрын

Interesting build, nice one 👌

@KeetonMarine 3 күн бұрын

Thanks 👍

@raycrocker2844 8 күн бұрын

Great video just subscribed and am now binge watching. I like your approach for lots of reasons but mostly because you explain calmly and in an easy way to learn without all the foul language normally associated to some of these types of videos.

@KeetonMarine 8 күн бұрын

Thanks for the subscribe, and thanks for the positive comment, I'm looking forward to getting some more projects filmed this year, Sam

@stephenlyttleton9032 8 күн бұрын

Did you not need to change the rear oil seal or spigot bush? Nice work.

@KeetonMarine 8 күн бұрын

Great point, I fitted a Bronze spigot bush but forgot to film it, and the rear main was dry so I decided to leave it for now because I plan on fitting a R380 stumpy gearbox this year and I'm going to change it then, at present I'm running an LT77 I'm not sure how well that will hold up to the OM606,

@RobinLeveille-i4v 5 күн бұрын

@@KeetonMarine Keep the LT77 only if (suffix G and H) it's very strong.

@katiehinds1648 8 күн бұрын

Well done mate . ❤

@KeetonMarine 8 күн бұрын

Thanks ✌️

@p1k68 8 күн бұрын

Great progress. Coming along.

@KeetonMarine 8 күн бұрын

Thanks, hopefully we can move along a bit quicker and get it up and running soon.

@AngusAbbott-qf8xm Ай бұрын

I have a discovery 200tdi in a series 2a, standard turbo, I run it at 20 psi boost , goes really well without any black smoke

@KeetonMarine 8 күн бұрын

Thanks, That's some boost is it holding up okay. on another note how is the 2a gearbox holding up I have a series 3 I'm thinking about fitting a tdi into.

@PillSharks Ай бұрын

Funny, I’ve just fitted a fox hybrid on my 200tdi. The original covered 320,000 miles and I asked the bloke what sort of condition it was in and he said he’d expect the wear to be half the miles mine had done! Let’s hope the fox one last as long as the original.

@KeetonMarine Ай бұрын

The quality seems really good the one I sent him to rebuild had over 200K and was still good, hoping this one will do the same can't see any reason why it won't and a little more go is good as well!!

@mylesmooney7505 Ай бұрын

Expensive thoes hybrid Turbos ❓️

@mylesmooney7505 Ай бұрын

300 Tdi sound work on it two❓️

@KeetonMarine Ай бұрын

Hi the turbos are £389 at the minute on the fox website. the quality of the rebuild seems very good.

@M94289 Ай бұрын

Turbo technics VGT. Once you’ve tried will never go back to any of these cheap crap! Instant boost at low rev range, no lag or delay. Ran one on a 200tdi challenge truck with 37”tyres would keep up with td5’s.

@KeetonMarine Ай бұрын

Thanks I would love to try a VGT turbo, would you use one on a daily driver ? if you follow the channel I'm currently building another 110 this ones going to be OM606 Powered should be a beast!!

@M94289 Ай бұрын

@ yes absolutely as a daily driver. Don’t adjust the wastegate on them as the internal veins are controlled by the pressure, they come ready set up and bolt on. Allisport are the main supplier.

@fergusmoloney Ай бұрын

Really enjoyable build and some very good editing. The oak looks great. What fasteners did you use to secure the planks? They look smart.

@KeetonMarine Ай бұрын

Thanks for your comment I am really enjoying this build, the screws are stainless screws pre drilled and countersunk.

@garystuart226 Ай бұрын

Hi, newbie here as just came across ur channel, wished to say what an awesome series of videos that ur putting together and massive thks for taking the time to make them, hope it was also ok as shared ur videos on some of the Land Rover forums I belong to, hopefully ur get more subscribers as justly deserved , never seen a merc engine fitted in a Land Rover before so will be following with great interest , had landies some 30+ years and currently have for my sins a discovery 3 , 🤣thks again and look forward to the next video , Gary

@KeetonMarine 8 күн бұрын

Hi, sorry I have just seen your comment. Thanks for such a positive comment. And yes please any videos shared helps hope you have great new year, Sam

@danielharrison5235 Ай бұрын

Love my fox revolution turbo, bought a year ago and still running strong 💪💪

@KeetonMarine Ай бұрын

It Seems really good, its amazing how different turbos can perform, maybe intercooler next!

@davidforbes6250 Ай бұрын

One year, well done.

@squeesmyth9025 2 ай бұрын

Was it originally a orkney with the cabin taken off ??

@KeetonMarine Ай бұрын

It was originally a Sportique XLR a prototype of the XLS but v drive, this hull was a test mule. Paul viewed the hull and the rest was history we started the build from there and now its living its life out as a fishing boat.

@Specky12 3 ай бұрын

Superb idea with the 2kW heater.

@KeetonMarine 2 ай бұрын

Thanks hopefully it will keep us warm 👍

@MwajumaJohn-f5d 3 ай бұрын

Very good ❤❤

@KeetonMarine 2 ай бұрын

Thanks 😄

@alexdavidson3344 3 ай бұрын

I didn't connect mine into the existing exhaust. But I did get a 3m section to route it out the back of the vehicle next to the exhaust. I found the heater fumes leaked into the cabin when it was side exit, because we all know what defenders are like for sealing

@KeetonMarine 2 ай бұрын

Thanks I have taken your advice and we are running it away from the cab to stop any fumes, going to try utilise the rock slider as part of the exhaust. Thanks 👍

@philss1 3 ай бұрын

Starting to look good! Very interested in the diesel heater fitment as I’ll be doing that when I get one. Waiting to see if you route exhaust into truck system or whether that creates back pressure on the heater so it doesn’t run properly. And waiting to see how the painting turns out.

@KeetonMarine 2 ай бұрын

Thanks I'm going to try and run it to the back or at least try get it away from the cab so it doesn't cause an issue. 👍

@migueldelaguardia 3 ай бұрын

Thinking ahead saves money and time.Good video.

@KeetonMarine 3 ай бұрын

Thanks, it sure does.

@DarrenOkeeffe-t3q 4 ай бұрын

Just wanted to say I think you’re doing a beautiful job, your attention to detail will really pay off in the end , thanks for taking the time to share it,

@KeetonMarine 4 ай бұрын

Thanks its a big build for us, we are really enjoying building this one.

@Wiltonmarines 4 ай бұрын

Cool as hell keep up the good work

@KeetonMarine 4 ай бұрын

Thanks Will 👍

@p1k68 4 ай бұрын

It’s great the way your design is integrating the bed with the chassis in a sympathetic/factory ethos.

@KeetonMarine 4 ай бұрын

Thanks for the comment, I'm glad you like the design we are trying to keep it looking like it could of been a factory option.

@노아-x4u 4 ай бұрын

Moore Jeffrey Hernandez Nancy Gonzalez Larry

@stevenquigley4208 4 ай бұрын

very nice to see a father and young son working on an engine....

@KeetonMarine 4 ай бұрын

Thankyou, It was really good to have Eddie with me on this video..

@Chris-uu3cp 5 ай бұрын

Great video, thanks for sharing! Looking forward to seeing more of your work!

@KeetonMarine 5 ай бұрын

Thanks, I'm going to try and get videos out on a regular basis on this truck build.

@rustandoil 6 ай бұрын

Simple fix..... Good result. Will save your clutch too! 😂

@KeetonMarine 6 ай бұрын

Thanks, I cant believe I waited so to repair it, the clutch is thank full of the repair😂

@rha4374 7 ай бұрын

Ye ,ye it says headline is it best UK river boat, but owner as usual referenced it English!! Always the same ignore, wales, Ireland, and Scottish dont they? I've stopped buying after 25 years my motorboat n yachting magazines for exactly the same reasons,also motor bike guide, always bloody England 99% of the time. And the mbm went up a £1 , previously it was £5.75 after last increase. We all have rivers to suit your lovely boat, shame it's taking me years to do mine on a miserable pension. From a very pissed of Scotsman

@squeesmyth9025 2 ай бұрын

He says English style fishing lol considering we are using bass boats in perch and pike comps

@darrenwalker6712 7 ай бұрын

That's a brilliant set up!!

@larrynatano7178 7 ай бұрын

So where's the video 😢😏

@KeetonMarine 7 ай бұрын

It's uploading now unfortunately our internet is a bit slow, it will be on today

@fireclown1225 7 ай бұрын

Hi Sam, Hi Brendan.

@KeetonMarine 8 ай бұрын

Testing the twin 225 OPTIMAX outboards after a service and some work to sort running issues

Ең жақсы KZbin

Пікірлер