I put a new carburetor and it just wants to take off
@BellyUpFishGarage2 күн бұрын
Idle speed is too high.
@Mytriumph650pre-unit2 күн бұрын
ITS A FOAM CANNON WITHOUT SOAP NO FOAM.
@BellyUpFishGarage2 күн бұрын
Yes’r, it is.
@Atrainswrld4 күн бұрын
Whats makes you think regular news wouldnt lie about every aspect of any type of news
@BellyUpFishGarage3 күн бұрын
What makes you think I don’t think regular news wouldn’t lie?
@PiperBuilder5 күн бұрын
Can’t you just move the stalk up and down to flash it ?
@BellyUpFishGarage5 күн бұрын
Nope. I got none blinks, regardless of what I did.
@rikeshkaushall45806 күн бұрын
Hello sir i really need your help can i get the files you modelled it on its for a school project im its too late for me to learn how to model one
@BellyUpFishGarage6 күн бұрын
You can find it at Makerworld by the user Christiansotelo2244. "Hydroponic Tower." makerworld.com/en/models/65860?from=search#profileId-78967
@joshhouse15597 күн бұрын
did you print the parts with supports?
@BellyUpFishGarage6 күн бұрын
No, I didn’t use any supports.
@melissasmithfe90969 күн бұрын
Wilson Scott Garcia Jason Thomas Nancy
@Bmount_359 күн бұрын
You are the man. I’m about to dig in. Have had no issues besides it getting stuck sometimes since new. My guess is shift motor has zero grease on it. Gonna put white lithium grease in there and clean the assembly. Also going to trickle charge the battery based on your advice. Will hopefully remember to update on how it goes!
@AndToTheRepublic4WhichItStands12 күн бұрын
Brother you could have kept the whole outer assembly and just popped the pin out of the top and only replaced the broken handle part.
@BellyUpFishGarage10 күн бұрын
It’s been a minute since I did this, but as best I remember, that wouldn’t work. I had to go in from the interior.
@AndToTheRepublic4WhichItStands10 күн бұрын
@@BellyUpFishGarage yeah you still have to get the whole assembly out to do it and it's a bit extra work but if you do want to keep the color matched outer shell piece you can swap the handle part out into the old one. There's a video on it. You have to cut the pin that with the spring on it that the handle pivots on to remove it but the pin from the new one should slide right in. Do you still have the Integra? I've had mine since 2013. It's a 94 ls bg33p color
@BellyUpFishGarage10 күн бұрын
I literally sold it earlier this month.
@AndToTheRepublic4WhichItStands9 күн бұрын
@@BellyUpFishGarage oh damn lol hopefully nobody ruins it. They've gotten really rare around where I live.
@BellyUpFishGarage9 күн бұрын
@AndToTheRepublic4WhichItStands Guy who bought it said he plans on restoring it.
@SlowDelSol14 күн бұрын
Just be careful not no move around the rod for the lock too much or you’ll disengage it like I did and turn a 10 min job into a 10 hour job
@BellyUpFishGarage10 күн бұрын
Good tip.
@jonag868817 күн бұрын
Thanks, your video made my project a whole lot easier now! Keep on sharing tips brotha!
@BellyUpFishGarage15 күн бұрын
Glad you found it helpful!
@prestonlove341119 күн бұрын
Saved me so much time you ARE the combustion wizard my friend thank you for your teachings 😂🙏
@peachezplaitzlyfetingz19 күн бұрын
Thank you so much for this video. I'm doing everything myself.🫶🏾 new subscriber
@orangielegros19 күн бұрын
I’m running tubes…. Thank you. I’m out
@monkee105621 күн бұрын
Thank you I've been have problems shifting it for about 2 weeks
@ThunderPickled22 күн бұрын
"When they eat the lead, the reaction is somewhat energetic." 😂 If you have a pet carrier to transfer them into, you can then place the pet carrier in a bucket of water and wait 10 minutes. No lead needed.
@BellyUpFishGarage22 күн бұрын
Rumor has it a long length of rope and a bridge works. #waituntilbubblesstop 😆
@dustinrossi938427 күн бұрын
Thanks 🤘
@maxvanrunkle105227 күн бұрын
Thanks!
@totalannihilation9065Ай бұрын
I'm actually using these for work and I need them to be a little shorter. Very good idea
@BillyBergesonАй бұрын
Now how do I do this when it won't run without being choked ? It's a brand new carb.
@BellyUpFishGarageАй бұрын
Are you sure it’s getting fuel? I’ve seen brand new carbs come clogged, depending on the make of the carb.
@billhill839Ай бұрын
Good job!
@jamiehalifax4954Ай бұрын
You can slowly unratchet ,ratchet straps using the othe lever..
@AudreyWalker-m4rАй бұрын
Thank you. This is the ONLY thing that worked for me with no see ums. Many thanks.
@TWMTradeАй бұрын
kinda late to the party and im no one of mention. but i would combine the face groups inside the cylinder before converting the mesh. this should allow you to select all the contraining boundries inside as a group after you convert. so you should be able select the inside boundary of that cylinder. create a copy then push/pull to measurement, then extrude.
@coolmre158Ай бұрын
do you run the pump 24/7 ?
@BellyUpFishGarageАй бұрын
No. I had it on a timer. However, when I was researching this, some people said they run theirs 24/7.
@benmignano9332Ай бұрын
I boiled a pot of water and added some alcohol and some Eucerin, and bathed in the shower with it. And for the finale, I placed body powder over the affected area. I felt like a Mint Peppermint Patty after that...Thanks
@bradleypeters6202Ай бұрын
Slayyy
@matthewzombies1458Ай бұрын
37,000 people have now been injured....
@BellyUpFishGarageАй бұрын
*Saved from injury.
@chrisespinoza2554Ай бұрын
Great video
@BellyUpFishGarageАй бұрын
Thank you.
@aidenaull9133Ай бұрын
Do you know if there is a way to convert these 420s to a standard foot shift? I know on the 2000s ranchers and foremans you could but I can't find anything on the 420s
@BellyUpFishGarageАй бұрын
I don’t. Wish I could help.
@Bmount_359 күн бұрын
You have to change the cases sadly. So it would be a full engine tear down. Not worth it imo. I’m sure there’s more stuff to change as well gear wise in transmission. I regret not getting a foot shift big time. Don’t fix what’s not broken! More wires=More Problems😂
@ballervision13642 ай бұрын
did your gear light use to blink whenever u turned it on?
@BellyUpFishGarage2 ай бұрын
Yes. I don’t remember the sequences and what they mean, but I got shift motor issues.
@joucellvelazquez15222 ай бұрын
Bike wont even start how am I supposed to tune it like that
@BellyUpFishGarage2 ай бұрын
If it won’t start you have other problems to sort out first. What is it doing when you try to start it?
@joucellvelazquez15222 ай бұрын
@@BellyUpFishGarage it just cranks but won't start. I replaced a ton of parts already on it and it just cranks . It does have spark but I'm guessing it's getting too much fuel
@BellyUpFishGarage2 ай бұрын
@@joucellvelazquez1522 So, it’s either fuel or air, if it has spark. Pull the carb and see if there is fuel in the bowl.
@joucellvelazquez15222 ай бұрын
@@BellyUpFishGarage thanks brother I'll definitely check that. I also opened the bolt on the bottom to bleed gas through the lines and it goes through with no problem
@BellyUpFishGarage2 ай бұрын
@@joucellvelazquez1522 Ok. Thats your drain, so there is fuel in the bowl. Is the carb new?
@JamesTaylor-lx9nv2 ай бұрын
So will a pz20 carburetor fit a atv that normally runs a pz19
@BellyUpFishGarage2 ай бұрын
I don’t know. Wish I could help there.
@joestamper56492 ай бұрын
good video very helpful
@Gkir12 ай бұрын
How would you work out the ratio it dilutes?
@BellyUpFishGarage2 ай бұрын
Easiest way, I think, would be to know the flow rate of the water going through the pressure washer, which could be timed by spraying into a bucket. Then time how long it takes to empty the foam cannon container. That should give you both flow rates. Take those flow rates and work out a ratio between the two. Should be able to reduce that to a dilution ratio.
@mariah1702 ай бұрын
You are a life saver! Just tried this after laying in bed trying to resist scratching my legs and thighs. I finally can lay down in peace. Thank you so much! 😩
@cultfan5227Ай бұрын
Glad it worked for u . Never had .any infections
@ThePl87pll2 ай бұрын
Can someone please help me. I have this exact carb on my coleman at125ut and it fires up immediately, idles perfect , but when I go to give it gas it just goes blurp blurp. Doesn't go fast and bogs down or something. I've tried relentlessly adjusting the screws with no luck. This is my 2nd carb like it. The first one lasted a few rides until it did this and this one lasted a full ride around the neighborhood until it started going blurp blurp. Helpppppp please lol
@BellyUpFishGarage2 ай бұрын
If it’s idling fine but dies under throttle it’s not getting enough fuel. Have you cleaned the carb? Was this a new carb? I always clean a new carb.
@ThePl87pll2 ай бұрын
@BellyUpFish Brand new carb. What is there to clean and where on it to clean? It's so clean looking already lol
@BellyUpFishGarage2 ай бұрын
@ThePl87pll Junk inside any of the passages from manufacturing. These aren’t built under the strictest of quality control.
@ThePl87pll2 ай бұрын
@BellyUpFish idk man. It appears to be getting plenty of fuel. Maybe I just got 2 bad carbs. I'm lost at this point
@sojourn15442 ай бұрын
Next time use butter instead of oil and it won’t stick at all. Great video!!
@BellyUpFishGarage2 ай бұрын
Thanks, I’ll give that a shot!
@longcashdj33812 ай бұрын
I can’t find the screw that adjust is it something covering it?
@BellyUpFishGarage2 ай бұрын
Unfortunately, some of these carbs don’t have the needles that can be adjusted. You’ll want to grab a new carb on Amazon. Make sure you get one that is adjustable.
@LumpyFPV2 ай бұрын
Noiiicceee. Should be ok on an intake plenum gasket, what do you think?
@BellyUpFishGarage2 ай бұрын
I wouldn’t have any issues using Vaseline there.
@user-hayden9992 ай бұрын
Thanks for posting this the kick on my blaster broke and I had nothing to ride now I can use the china boat again
@NoLyinEvry1sDyin2 ай бұрын
Dawn and bleach love each other just fine
@PiperBuilder2 ай бұрын
One of the best colony’s I’ve ever had didn’t do anything for 6 months. Also, they are in dearth conditions. My new bees never did much in their first year.
@BellyUpFishGarage2 ай бұрын
They’re definitely not doing anything in the upper box. We’ll see what happens.
@t1mmy132 ай бұрын
Is that tube food safe? Usually those transparent tubes are at risk for leeching into the water
@BellyUpFishGarage2 ай бұрын
Tygon E-3603 is food safe.
@Ninoo1872 ай бұрын
Smart guy
@richardlange90942 ай бұрын
LOL, I cannot get it to work. Guess I am just too old
@BellyUpFishGarage2 ай бұрын
Where are you getting hung up?
@richardlange90942 ай бұрын
@@BellyUpFishGarage Thank you for the reply. I gave up trying to modify the part and just built my own with fusion. No matter how I tried I just could not get the STL file to come up without the triangles. I do want to thank you for your response. At 80 it is often difficult to get what seems simple to work.
@stevekress95852 ай бұрын
I live with three mature trees over my roof. I put these guards on my gutters and after a year my gutters and the guards are free of leaves and twigs. What is nice is they are very rigid and easily allow debris to blow off. There is no front lip to catch stuff. The more open mesh easily handles heavy downpours. I am very impressed. If you have to take the little extra step to secure them, do it! They are worth it.
@Derek_Garnham2 ай бұрын
my friends car came back from having a new spring fitted, it didn't drive right, when he looked there were still a few heavy duty zip ties compressing some of the coil. Maybe useful as secondary protection once the straps are tight.
@dylanmccullick97102 ай бұрын
Any update? Did you have to replace any parts?
@BellyUpFishGarage2 ай бұрын
No. Turns out it was simply my battery. I have had one other “won’t shift” issue since this video and it was the shift motor getting stuck. I took the motor apart, put it back together and it’s been shifting like a champ ever since.