Very nice range test Small but terrible Just imagine he was able to reach 1.5km for the sum of 3km upon returning That's good enough my friend Very nice sharing

Super Mario!

Cool !

Nice one Sir❤❤❤ ..anong app yong unang ginamit nyo Sir?

Ang dami nang mga collection mo bossing. Pwede na e benta ang less important sa line up.

It could be more nicer if the body color is gray or black. But BetaFPV likes white.

Ok lang sa middle ang bracket?. Hindi naka block sa GPS Module.

Saan ang location nito Bossing? Parang nasa pinas kana nito.

Hindi po compatible ang RC-n1 at ang RC-n3?

You did much better at wire management compared to indiatownfpv

Nice video on neo .just got today with controler patch works on it did you try yet also would you do range test on new firmware mini2 1.15.1 please Thomas from Ireland 🇮🇪

To connect a 2s battery to mobula7, do I need to change anything in the settings or in the flight controller other than the motors?

Terbaik bro... Paling utama, 👍signal dan jarak...

Nice one bro 👍🏾

cool, its a sport modes?

🤝😎

Very nice

Wow that's really amazing content my friend 👍 I actually don't understand its technicalities So I salute you for that content Keep up the good job my friend Like-27 15:08

Ayos Salamat Bre

DJI RC N2 and N3 also work well with Simudrone

Bag password?

iphene de olur mu

Very similar. I use freerider on Android, using a Xiaomi Poco X3 with a Jumper T20 (rarely an Emax E8) The only difference, that I have a dronemask2 goggles to it.

Thank you for sharing your video tutorial🙂

Maingay bro, alam ko pwede tangalin yng noise habang ng record

Kpag bruslesd motor sana less ingay, pero iban din ang price nya

Nice Build 👍 , how do you do for put antenna in the tpu because i have the same vtx and frame but i don’t see how i can setup the antenna in the hole, thanks U

What rc and goggles do you recommend for the Pavo20 Pro Brushless Whoop Quadcopter

Nice

Mine says controller not detected but it is connected I don't know what's happening

can i put ipad 8 in (10.5inch)

is this SPI ELRS Mobula? the problem with my UART ELRS Mobula 8 is that I've broken ceramic antenna, then soldered wire antenna which was even better and then while trying to straighten that wire the pad it was soldered came off... I so I've soldered Happymodel EP1 with external antenna, but the problem is that if I switch off UART1 Serial Rx and turn on UART2 Serial Rx -- I do not get video from the VTX, otherwise I can't control quad using the external EP1. it is one or other. here's the answer form Happymodel: "As this vtx and the onboard elrs receiver share the same MCU, so if you only disable the receiver, then the vtx will not working . If the ceramic antenna was broken , you can solder an copper wire to replace . It's very easy . Just solder a 31mm length copper wire to the pad that marked."

Info about the props???

Is this compatible with rc2 controller?

Need PO ba merong data Yung cellphone boss para maka pag palipad?

Anything under 800 euro

What do you recommend

Do you know where i can buy my own pre built

You will have to let us know how the 1st flight went.

Coulda been a NICE video. Not many show thumb can or editions to mob 8’s!

Iv always liked the look of the speedybee frames and oneday will buuld one to add to my collection. Nice job on the build.

Where did you bought thig bag

That ipad 9th gen

have the rcn1 but the drone are the 4k dont know if they change something in the controler, but i cant get it to work, says connection to controller failed

Thanks for update on mini 2 i watch all your videos you are the only one doing range test thanks again Thomas from Ireland 🇮🇪

Built my O3 version. That came to 249g as well.

The googles are a copy of eachine right?

Hi

Nice video bro. thanks

Done mine,not tested yet maybe later today.