Mine won't bind... and I have the same setup (9XR Pro, XJT, X8r)... you don't show any of the radio screen information that needs to be set for this to work!! I need to see the menu settings to make sure the radio itself is setup properly (protocols)... please help!! thx

A very helpful step by step guide. Thank you.

It's upside down

Thank you very much .. I really needed it ..

What is that kind

Very helpful. So in self level mode we have a 6axis gyro?

Hi my friend, looking through this vid was great but I have moved from IC to electric and need to know how to set throttle cut out , many thanks

l dont have global variables in my opions in FLight Mode

How can we test the 5V output?

Can i operate two receivers simultaneously? I dont wanna switch between them.. I just want sticks output in one receiver and switch output in other receiver😊

Cover your flight controller with black and non reflective mat... And put a small hole for air follow. And u should got a good altitude hold.

I’m having the same issue even free calibration. The motor only turns on after 50% throttle any tips?

THANK YOU SO MUCH! way better than painless 360's' crap videos

Thanks I'll give this a try before I tried to do it in one go but the heavy gauge wires just absorbed all the heat

I lovea aviatio

Thank you so very much🎉🎉

It is unbalanced buy a new prop or balance it

How to create knife edge mixing for rudder to elevator and aileron but having different amount of mix for right rudder and when you do left rudder it is a different amount?

How do i setup my landing gear to have steering for the front wheel?

Cant figure out how to setup steering on my landing gear. Any ideas?

What cable is that going to your phone, is it USB to micro? USB to USB-C? Micro to Micro? Got a used one and trying to figure out the step by step here.

You do not show how to set it up on transmitter. I got nothing from this video.

Splendid. Just pulled out a plane to fly from the cobwebs of my basement. My spectrum radio took a dump, went to find the taranis, and an rx, but totally forgot how to bind it.

Hahaha

Thanks !!

Great video this was exactly what I was looking for

simples mas objetivo.

Very rare, but every once and while I find a perfect video exactly what I was looking for thank you brotha

Is it possible to bind it with rc car?

Thank you.

Very helpful, thank you very much

Hi Mark, excellent video… can you do the same for the D Series?? I couldn’t find a link in your comments.

Is the frame dimensions important in the multirotor firmware? According to this, I understand it's no... please answer me .

Technically this is incorrect, you should not solder two wires in parallel. You are supposed to shape the end of the wires into a 180 degree half loop like the letter c, interlock the wires and then solder.

How to mix two servos in a flying wing?

This is the best guide On KZbin for helping newbies learn Flight Modes and Global Variables - THANK YOU! Other people try, but fail. 👌👏👏👏🖖🏻

what type of solder you used ??

Terima kasih untuk videonya, saya akan setting elevon di turnigy 9xr

Can i replace the potentialmeter with resistors instead for led lights on and off switch on remote control i still got the potentialmeter on mine i want to remove the potentialmeter

Do you know what the common failure component in these power supplies are? My mac wont power on and I tried jumping the wires to see if it powers up but its a dud.

Thankyouuuu ! Very gooot presentation of uncommon use .. i allways used mixes an they were pain to change..

Can’t setup my Taranis

How to burn out your servo when turning left = just select over 100 percent…

Did you tell me power jumper for macpro power supply 2006. I need to power on with out computer.

Nice video thank friend Mark

Nice and simple opinion - thanks a lot!

Very useful. It helped me understand derivatives and integrals even more than just using theory lol. Thanks!

Hmm I’m getting the same readings you’re getting. Still no power though

dam

Hola, me pregunto si se pudiera hacer que con el control taranis se pudiera hacer la función que con dos palancas activas al mismo tiempo se accione un servo y si alguna de ellas no esta activa no se mueva el servo