PLUMBING WORK FA

Пікірлер

@texrain6589 12 сағат бұрын

Whoever did that copper piping for the tmp is brain dead.

@rubentoledano7814 18 сағат бұрын

Good sales pitch

@o.j.flores6181 23 сағат бұрын

Soldering with ball valve on the open position is going to cause ball valve not to shut off properly, due to solder running through! Ball valves should solder or glued on to off position!!😅

@wittywoo9559 Күн бұрын

Next plumber Is opening walls 😂

@MrElpariente08 Күн бұрын

Peiple that remodel bathrooms do this. Plumbers do the plumbing

@MrElpariente08 Күн бұрын

Rich people spend on something like this becaise they dont know what to spend their money on anymore. Im saying this because mine are made of gold lmfao

@jordacheroybal 2 күн бұрын

Off set the pop up or use an inside cutter to cut back the pipe

@carlstrohm3785 3 күн бұрын

Pick up a nice flexy at the box store.

@johnwquick3616 3 күн бұрын

A slip and fall onto this spout would be messy

@khmcs 3 күн бұрын

조심하지 않으면 수평 배관에 구멍 뚫는다.~~

@curtischung1009 3 күн бұрын

This dude really call a sawzall a whole saw?🥴

@patrickchavez3848 4 күн бұрын

He didn't feel anything, he knew what it looked like! Unless he's blind. O is he blind?

@maintenanceman1015 4 күн бұрын

Ooops you forgot the chrome ring ,the first time . Bet as soon as you though I`m done, darn ring .

@davidkleinthefamousp 4 күн бұрын

Uhhhhhhh u didn’t anchor the ring. Naughty naughty.

@seancoulter9871 4 күн бұрын

Aren’t you good enough to not have to measure a stop good god

@thegeneral1283 4 күн бұрын

What size wholesaw bit are you using

@MkNEAC 5 күн бұрын

Tubular or la trap will do just fine

@VincentCaponero 5 күн бұрын

Clean work! Next time use an inside and outside iron to get the best seal with the lead and oakum joint. Cheers

@slovakjakpica 5 күн бұрын

Undermount sink or way to get leaking faster

@brandonTHEshiados 6 күн бұрын

Yeah i would have trimmed the pipe down, trimmed the back of that wood finish and put the 90 fitting flush with the wall and it would have worked just fine. Only time you couldn't do that is if it were tee'd off with galvanized pipe right at the wall and the pipe was too short.

@MasonAhrens-dt7or 6 күн бұрын

One time a while back I used 50/50 on water pipe repair but I turned out ok right?

@MasonAhrens-dt7or 6 күн бұрын

Hey man question for you the old trip lever price pfister tub drains did anybody else use to clean up the tailpiece and solder it up?

@hugoescobar8935 6 күн бұрын

Muy complicado

@o.j.flores6181 7 күн бұрын

A street 16 (22) bend from stub out should work! It will give you the play you need!

@r10tecnologia94 7 күн бұрын

PELO TRABALHO DEVE SER SUPER BARATO KKKKKKKK

@ilikethesoundofthat9608 7 күн бұрын

what kind of bit is that

@DabblelyDiddly 7 күн бұрын

oh nice, their finally getting the clue that silicone isnt glue and giving hardware with these junkers

@seancoulter9871 7 күн бұрын

Ya a bag p trap with an extension you nub.

@jamess1787 7 күн бұрын

I just pulled my bradford white out two days ago. 13 years on a 6 year tank, whi can complain

@cengeb 5 күн бұрын

@jamess1787 had good luck with Bradford white mine is like 18 years it out lasted 2 previous Rheem. I will never go with Rheem or a o Smith. Bradford white for the win

@damocles5047 8 күн бұрын

Just screw a bolt in those plastic and hammer down gently, i never cut it with machete or hit with hammer after its stuck and wont go down deeper like it should.

@R4MP4G3RXD 8 күн бұрын

Can we just take a moment and talk about how damn stupid these modern sinks are? The faucet is literally 3 inches long right above the drain that just about fits from the rear side of the basin that is almost big enough to take a shower in. Hand washing is a pain because your hands don't actually fit under the faucet but at least it looks good ig

@anthonygrant7952 8 күн бұрын

Trolling!

@Jugoslavija 8 күн бұрын

Now I finally understand why the dutch call a plumber a "lead pourer" (loodgieter). I never knew why tf they wouldn't just call it waterinstaller or something, why "lead pourer", never made sence.

@jacksplumbingvideos7147 9 күн бұрын

you will be crying about it when you are the one who ends up needing to remove them.

@TheBsmanatwork 9 күн бұрын

Silicone not going to last

@fiume2006 9 күн бұрын

Fermit auf dem Gewinde verhindert das Festbacken vom Gewinde vorallem bei hohen Temperaturen, beim auf und abheizen, merkt man spätestens beim Ventil wechsel , unabhängig ob man das in USA oder GB oder sonst wo macht ....