16 сағат бұрын
Пікірлер
@richardwooten3072 2 күн бұрын
WHY SO MUCH WHOOPLA , IT DECIEVES THOSE UNAWARE , MAKING THE BLADE LOOK DAMASCUS ! GHEAP TRICK RIPOFF ! BE EMBARASED .
@luismosquea9261 6 күн бұрын
I would like to know which font was used for this name?👀
@Nathan-vq9ch 9 күн бұрын
Lazer craze on a blade v/nice
@BGCNCfiberlaser 9 күн бұрын
Thanks
@Rishuk25 9 күн бұрын
💐 Thank you
@MDC_316 19 күн бұрын
What kind of Mopa fiber laser is used here? How many watts?
@BGCNCfiberlaser 9 күн бұрын
60w mopa laser
@palmbeachjewelrydesignlab5253 22 күн бұрын
Can you share parameters?
@TDMPlayer20 27 күн бұрын
What is the parameters for plastic engraving please reply
@khangeearms3527 Ай бұрын
How much speed and power and frequency required please for glock lower polymer
@BGCNCfiberlaser Ай бұрын
if use 50w Raycus, power 50, speed 1800, fre 60, hatch 0.05
@BGCNCfiberlaser Ай бұрын
lens 100x100mm
@khangeearms3527 Ай бұрын
@@BGCNCfiberlaser for lower
@khangeearms3527 Ай бұрын
@@BGCNCfiberlaserfor both designing or cleaning same power ,frequency speed
@AA_gold5851 Ай бұрын
Why you not tell speed and power??
@BGCNCfiberlaser Ай бұрын
power 80 speed 200, hatch 0.04 deep engraving
@BGCNCfiberlaser Ай бұрын
power 20 speed 1200 hatch 0.05 cleaning
@zyfix Ай бұрын
Hello, my dad recently purchased a laser and im getting into it as well. Love the deaign on this. Quick question, i can see the cut and clean phase as its engraving but when the laser is going over and making it completely like grey what ia that pass called or what is it doing? Sorry like i said very new only done a few things on my dad's laser but interested in learning more. Thanks for your time. He has a fiber laser as well not sure exactly what specs but has a variety of lenses available and he uses the lightburn software.
@BGCNCfiberlaser Ай бұрын
first cleaning, then start engraving
@je6842 Ай бұрын
Hello, I ran across your video and it's the only one I have found with autofocus and Ezcad3. That's what I'm using. I don't understand the part around the 1:31 section of your video where you state the fixture offset. How do you calculate that to get 65? Thanks!
@BGCNCfiberlaser Ай бұрын
fixture offser means the height of your product, use ruler to calculate
@khangeearms3527 Ай бұрын
How can i get this design
@BGCNCfiberlaser Ай бұрын
our customer send us the video, you can contact him www.youtube.com/@1776laserco
@khangeearms3527 Ай бұрын
Wawoo
@octopus_4192 Ай бұрын
Hi can you share with me the settings for cutting 1mm I bought one and I don't know how to cut
@BGCNCfiberlaser Ай бұрын
power 95 speed 200 wobble 0.2x0.02mm 15 loops lens 100x100mm
@octopus_4192 Ай бұрын
@@BGCNCfiberlaser Is 110*110mm lens the same as 100*100mm?،Also, do these settings apply to copper or do they have different settings?
@EhabPlaysGames Ай бұрын
Would this work on Silver?
@BGCNCfiberlaser Ай бұрын
yes, on silver different result
@EhabPlaysGames Ай бұрын
Can I use Raycus?
@BGCNCfiberlaser Ай бұрын
it depends on your material, some can, some not.
@EhabPlaysGames Ай бұрын
What are the settings please? I have EZCAD 2 - Please do a tutorial on EzCad 2 with in-depth information, parameters, power, speed etc.. Please I need this
@Batmandarkknight. Ай бұрын
Why so fast ?
@-yogeshshinde2939 2 ай бұрын
Ma'am. How many hours got to finish that engrave?
@BGCNCfiberlaser 2 ай бұрын
Around40 mins
@Shurdle3D 2 ай бұрын
rename this video to "how to design a name to cut out"... don't show a single setting or how to cut the steel and say "contact us" what a waste of time.
@BGCNCfiberlaser 2 ай бұрын
Setting hide is not for users, but for competitors. We paid a lot of time to test it. We can send you settings.
@Shurdle3D 2 ай бұрын
@@BGCNCfiberlaser that’s doesn’t even make sense, what if I’m your competitor?
@shadabislam12345 2 ай бұрын
What's the cost of machine...please help
@BGCNCfiberlaser 2 ай бұрын
From USD2800 to USD4000, you can contact us [email protected]
@Hamayunshahzad-pg8ho 2 ай бұрын
How much
@BGCNCfiberlaser 2 ай бұрын
Around USD7000-USD10000. You can contact us [email protected]
@Hamayunshahzad-pg8ho 2 ай бұрын
How much
@Iamexplorer96 2 ай бұрын
Price
@BGCNCfiberlaser 2 ай бұрын
around USD3000, you can contact us by email: [email protected]
@mehvansaeed7 2 ай бұрын
Thanks
@jaber4love 2 ай бұрын
Mine fuses the cut place back after finishing. What setting you used
@BGCNCfiberlaser 2 ай бұрын
what is your material? Brass? I used wobble, 0.2x0.02mm
@BGCNCfiberlaser 2 ай бұрын
wobble is uses for making the cutting line bigger
@Davidesquivel-iv4pw 2 ай бұрын
What settings are you using?
@alsahoofa 2 ай бұрын
Is this 50w fiber laser ?
@BGCNCfiberlaser 2 ай бұрын
yes 50w
@bigrednick100 2 ай бұрын
I’m curious, though after you have engraved the aluminum does an oxide layer form shortly after?
@BGCNCfiberlaser 2 ай бұрын
no, it won't.
@dziorgas 3 ай бұрын
I need your advice. Which 50W fiber laser is better for cutting and engraving silver sheets: JPT or Raycus, or is there no significant difference for silver? Also, what lenses are preferable: a 110 x 110 mm lens or a lens with a smaller working area? Thanks for your answer.
@BGCNCfiberlaser 2 ай бұрын
Hi, sorry for just saw your comments, you can use 100x100mm lens, 70x70mm also is fine. For cutting, silver, no significant difference between Raycus or JPT. When laser source has problem, JPT brand has monitor software and we can confirm if that is laser source problem.
@MasterblasterCoreldrawDesigner 21 күн бұрын
I have 60w jpt source good results
@frankbemo 2 күн бұрын
@@BGCNCfiberlaser Can you tell me which one is that monitor software and we can confirm if that is laser source problem?
@RTCDigitalS 3 ай бұрын
Is there burnt edges around the cut ?
@BGCNCfiberlaser 2 ай бұрын
no, this paper is thin, no burnt edges
@vilalaser 3 ай бұрын
What Wobble configuration did you use?
@BGCNCfiberlaser 3 ай бұрын
0.2x0.02mm
@lizardfreakboy 4 ай бұрын
I used your settings on 2mm brass and got to the point that I could see it coming through a little after about two hours. It didn't cut through all the way and, couldn't get it to pop out. How long did this take you and what watt laser are you using ? I have a 50 watt JPT
@BGCNCfiberlaser 4 ай бұрын
What lens did you use?
@rohitpanthi314 Ай бұрын
Where are you from ?
@BGCNCfiberlaser Ай бұрын
@@rohitpanthi314 we are from China, the one made the video is from America
@dillanwade3525 4 ай бұрын
Beautiful
@BGCNCfiberlaser 4 ай бұрын
Thank you
@mohamedtahifa2611 4 ай бұрын
Can i have the wobble parameter
@BGCNCfiberlaser 4 ай бұрын
Sure, diameter 0.2, distance 0.02
@Hamayunshahzad-pg8ho 4 ай бұрын
Price pk rupee?
@BGCNCfiberlaser 4 ай бұрын
Around USD3000
@Hamayunshahzad-pg8ho 4 ай бұрын
Is thi available in Pakistan where
@BGCNCfiberlaser 4 ай бұрын
Ship from China
@gojfert 4 ай бұрын
Hi will you tell me the setting for engraving silver...I have a 60w MOPA too thank you
@BGCNCfiberlaser 4 ай бұрын
Black on silver, 300 speed 50 power, 0.01hatch 200ns 48khz
@carltonlovejoy 4 ай бұрын
My 80-C JPT, 300mm lens, perfect cut in letters on the edge of a penny ! .002" linewidth ! Requires incidence of less than 22 and 1/2° for repeatability. Been in Laser since 1977.
@BGCNCfiberlaser 4 ай бұрын
Good to know that.
@anthonyramos3741 4 ай бұрын
Hi daughter, thank you for sharing your expierence and expertise. ❤
@blejs9260 5 ай бұрын
What is the name of that font?
@GroundedConceptsLLC 5 ай бұрын
Own a few lasers and still enjoy watching these videos. Thank you for sharing!
@BGCNCfiberlaser 5 ай бұрын
Thank you!
@MrCcfly 5 ай бұрын
how long it takes to cut that ?
@BGCNCfiberlaser 5 ай бұрын
40mins around, 0.75mm depth
@MrCcfly 5 ай бұрын
you mill first then use laser or ? and how strong laser is ?
@BGCNCfiberlaser 5 ай бұрын
We use 50w. We didn’t mill it. Only use laser. But for real application, most customers use milling machine
@mohamedsaadany8883 5 ай бұрын
Price?
@BGCNCfiberlaser 5 ай бұрын
depends on power, range 1K-6K, you can send me email: [email protected]
@FlacoGonzalez-u6h 6 ай бұрын
How much, where can I buy, and how many designs do you carry?
@BGCNCfiberlaser 6 ай бұрын
Pls send message, [email protected]
@khangeearms3527 6 ай бұрын
How to get this design from you
@BGCNCfiberlaser 6 ай бұрын
we send designs for free if customer order the laser from us.
@BGCNCfiberlaser 6 ай бұрын
do you have Bogong laser?
@dillanwade3525 4 ай бұрын
How much for the laser?
@BGCNCfiberlaser 3 ай бұрын
@@dillanwade3525 around 4K US dollar
@khangeearms3527 Ай бұрын
@@BGCNCfiberlaserI have already 50watt laser possible on that
@theredbeardreport 6 ай бұрын
Do you have the file for this? Do you have to sand down the texture before you apply this?
@danieltokov8077 6 ай бұрын
How to clean it after cutting?
@BGCNCfiberlaser 6 ай бұрын
kzbin.info/www/bejne/on3bpIJtetJ3kK8si=m2cruuj12K0WZg7X sorry for the delayed response. Pls check above video.
@preddy2x4 6 ай бұрын
hi I have a problem. new 50w laser. I installed the drivers for windows. then I open ezdca2 and when I press the light button, ready comes out and the program freezes. if I turn off the laser the program unlocks. plus it doesn't give me the red light figure or even marking. can you help me thanks.