Just turn it off then, Hold down on the power button and it turns off.

Press and hold power button on base for 3 seconds

Press M to select the alarm mode, then use the up or down arrow to set whether the alarm should be on or off and the same for snooze. I know I'm writing this a little late, but I searched and managed to find instructions on the Internet. I hope it helped someone else if not you :)

Make sure year is set correctly.

You gotta click S twice then change the year to 2023, at first mine was stuck at 2009 and I thought it was military time but I was wrong 😂

Using the ^ button on the back of the lamp

@@akahisanders1492 I figured it out about 20 min after commenting I thought it was military time aswell

@@akahisanders1492 Mine does not have an S on it to hit twice, my layout on the back is set up different but it's the same model, go figure. My controls on the back go up and down, not side to side above the battery casing. the top button looks like a box with an x in it, the second button looks like a sun, the 3rd button is the M button and the next 2 buttons are the up and down buttons, and none of these buttons bring up the year by hitting it twice.

👍👏Thank you, I've been on the wrong day of the week for almost 2 years 😂 I also thought it was a military time setting@@akahisanders1492

Did you learn how to set it up or did you return it ? 😆

Hello, how to turn on the clock?

The video only shows how the “back buttons” works. The temperature is only a reference, not that precise. If the day cannot match with date, you might set a wrong year.

Did you ever figure out how to set it up 😆

@@MichaelHalloween31 Can you tell me how to set the day of the week to the correct day?

@@erayshop5879 i didn't see a place to set the year & it skips past the day on the "s" button. The older folks among us would like better marked buttons

Not to sure how you set the year

YES. If you mean 'delayed arm', yes it has this function. You can skip the video to 2'37'', it will show you how to set up the 'delayed arm'. Importantly, you should use a remote control to 'arm' the system after setting to achieve this function.

Hi, there are 2 ways to cancel the notification pushing. 1.Turn off each accessory's ''Alert'' in the setting of each accessory. And turn off ''Alarm Notification'' in the ''Setting''. 2.Turn off all accessories' notifications: ''Me'' in the home page - ''Settings'' - ''App Notification''

Hi, thanks for your comment. Please check the ''Zone attribute'' list then you will find ''ARM/HOME'', you can move all sensors into this zone and they will be alarmed whether you are away or not.

Hai, jika anda bermaksud kelajuan operasi, anda boleh memperlahankannya dengan menetapkan kelajuan main balik.

Sorry, this speaker was sold out.

It should come with a charging cable with USB end and micro-USB end, you could use an adapter or power bank to charge the microphone.

Any button of the remote is OK. But you should firstly long press the button on the base station that looks like signal.

It can read the MP3 songs in the micro-SD card. But the volume might be low, it's not recommended to use the music app.

您好，请问您的问题是否为：在报警器处于布防的状态下，您触发了感应器，但是手机没有收到报警短信通知？ 如果是这样的话，解决方法：在您触发配件后，报警器主机是否发出了警报？如果主机发出了报警： 1.确定您插入报警器主机的电话卡是有余额的，可以正常使用的。 2.在主机的设置页面再次检查，您是否保存了报警短信的号码 3.请查看您主机的网络信号是否很弱，如信号很弱，容易造成短信延迟发送甚至无法接收短信的情况，建议换个信号好点的地方放置主机 在您触发配件后，报警器主机是否发出了警报？如果主机没有报警，请检查您的防区设置，是否该感应器的防区设置了布防状态下不报警？

@@erayshop5879 您好 还是不行，请问您们有类似微信号或者客服吗？因为这样联系方便点

@@kevinhe7319 您好，稍后会有客服加您的微信

Hi, Gadin, you can add up to 20 remotes and 40 sensors (it has 4 zones, and each zone allows for 10 sensors.

If you forget the password, you can reset the host, it will return to the original state, the default password will allow you to modify the password

Normally a thief will not have time to look, if there is a switch to turn it off. It's a nice gadget for a small price.

Usually you have to open the back panel, to access the switch. In this process, a tamper alarm will be triggered.