Just needed a little help maybe next time he'll bring 1 or 2 friends till he gets it down like most people said here everyone has to start somewhere

Give him a break! Look at that wind ....

New one is 125$. Slap it in.. done

When in doubt, back it out. Way easier to hold your line with your stern into the wind.

Painful to watch.... but where is Part 2, him coming back in? haha

Why don't you have your know it all wife give him some lessons?

proof that money can't buy you skill

I can see why that’s like the tides coming in you can see the current and I’ve been there plenty of times like that when not directly at that place butI know how That Current Will just pull you.

He better not do that when the Coyote is around, or he's through.

Starboard stern and push the dock with a boat pole..lol

Shes definitely with him for only the boat lol

I'm a life time commercial fisherman and I dont mean to be ugly but this guy should not be trying to handle a boat with that much hp he's obviously too inexperienced, good luck tho ;)

This guy shouldn’t be driving

I grew up on the house boats at the end

Too funny -- I had the same issue on the same pump and also had to junk it because I couldn't get the end of the pump off the axle (lock nut is there but corroded on). Seems like that seal leaks and causes a failure often

Very nice and interesting video,

all he had to do was turn as he was leaving his slip and he would be good to go but but you have to start somewhere and learn as you go

Great videos, thanks for sharing

I love going out to Block Island too! Never enough time to stay there. prefer docking around old Harbor though A lot more convenient to town.

Go fast boat needs a lot of training! With no current he can’t even do it!

you might try adding gas to the Primary rather than the Secondary side of the carb, since nothing flows thru the secondaries when you try to start it.

It has always amazed me that you need a special license to drive a truck, and have to pass a driving test to do so. But you can walk into a boat dealership without ever having operated a boat, and buy a boat!! With the expected results!!

Ridiculous. You don't buy a boat that is beyond your abilities, this guy is clueless and a threat to everyone on the water, total neophyte, start with a 20 foot or smaller after taking a boating course if you're this unseasoned and completely daft on what a single screw can do in a small space.

He probably forgot to trim the stern drive all the way back down after his last run.

the activator? why don 't you activate intelligence?

wow

"Great boat, but ya need a new set of plugs whenever you leave the doc" ~ this guy😆😆😋 Good job staying off the throttles😊 If there's a current coming across the bow left to right (capt view) it would've been easier to drift the nose starboard and back out of the marina I'm thinking😎 Esp with no bow thrusters

Really not that bad looks windy enough to be a hassle. Might be a single screw at that size didn’t hit and boats barely tapped the dock

We all would love to have this boat and do the same thing. It's kinda like us with our muscles cars driving through the car hop restaurant over and over again so people would see and hear our cars. Love it

He cant drive

Nicely done, imho, patience and experience apparent.

That sort of boat says small weiner

He’s down an engine! Operating a twin engine boat that size with only one running is a BIA, I know… I have a 36 with twins 500 HPs (no where near the power of this boats), I’ve done it and it’s not fun. So please don’t judge his driving abilities until you know the facts, and also have a bit of experience driving a boat of this caliber. Running a twin engine boat with one engine you’re pushing and pulling one side only so it is not as simple as just turning the wheel. Think about it, you have an engine pushing/pulling from one side only. I actually respect this guy for doing it as good as he did.

Just when you think you've seen it all

How can someone this stupid afford a boat like this?

Nice video, I may have the same problem but now I know what to do to take it apart and find out. I like the comment of using WD40 and replace the bearing to fix the problem. But I wonder if that’s even worth it since they all seem to have this gasket leak issue. The problem will just come back eventually, right?

The wind was whipping those flags. Blowing him side ways. Been there done that, wind and current, single engine, he got it done.

Hi William, do you happen to recommend how to the begin learning more about the Chrysler marine engines? I have two 440 Chrysler engines that currently do not work and want to attempt to start them up myself. Previous owner was a liveaboard for 5 years and had not taken out the boat to ride.

Sounds like my old Scottsdale

Coming from a guy with bow thrusters lol.

I think he done a fine job

I've had two jabsco pumps go exactly the same way, it's not the motor, but the bearing you don't show in the video that fails, it's rubbish of jabsco to not seal the motor chamber properly, if you have one and it still works pull it apart now and oil the bearings and seal it properly with silicone before this happens

That was painful to watch....

I had exact same pump,lasted about six months. Wasn’t cheap either,exact same failure as this guy.

Holly shit that was painful to watch..all the while thinking to myself he must be a newe yorker..... then I saw the registration numbers...

I have pakpump the micro switch was the problem

Yep he did a great job ,way better than the people than filmed and posted this video .must be nice being so perfect!

No loud

Maybe a little too much Jack Daniells on the way to the slip for these experienced skippers?

There is nothing sounds as beutiful as a Donzi.