Lloyd Industries Inc.

Пікірлер

@tylerwillging8074 5 сағат бұрын

That thing looks sick! Really stuck the landing too. Your craftsmanship is really nice.

@letsMakeItFly 3 сағат бұрын

Thank you sir!

@jewelpro9591 10 сағат бұрын

It's always interesting to find out how much the wings weigh and their size. And also how much the airplane itself weighs.

@letsMakeItFly 10 сағат бұрын

@jewelpro9591 absolutely! I think i forgot to mention that in the video but the wings each came out to about 380 grams with all the electronics and the aircraft all up weight was 3088! Previous version was 3306 AUW! So a nice improvement there.

@letsMakeItFly 14 сағат бұрын

Thanks for watching everyone! Please let me know your thoughts and share any ideas you might have!

@Oshan_Dissanayaka 17 сағат бұрын

Wow. Nice video. Good Luck and Keep going up.

@letsMakeItFly 15 сағат бұрын

Thank you very much!

@TNT_FPV 23 сағат бұрын

👍👍

@LloydKiddos 14 күн бұрын

That’s so cool

@letsMakeItFly 13 күн бұрын

Thank you!!

@brianhutchinson7863 19 күн бұрын

You're nose wheel gear leg is too short. Wing AOA is too shallow for correct take off roll out. The plane shouldn't pitch downward wing striking the runway on take off. Good work with using heat shrink covering film in a non conventional way though. Also if the carbon that you referred to as "Rod" are actually Rods (solid carbon) you should probably use carbon tubes. Not sure if this is a language thing but I've noticed a lot of people refer to carbon tube as "rods"

@letsMakeItFly 19 күн бұрын

Thanks for the advice! Yes I mean carbon fiber tubes they are indeed hollow. I believe the wing stricking on takeoff was because of the autopilot though because it was on stabilize mode and while I was flying it pulled to the left hard the whole time. The wings may have been asymmetrical but the autopilot should have done what it had to do to keep it level and given the fact that I was still able to turn right I believe it was an autopilot issue. Thanks for the comment!

@brianhutchinson7863 19 күн бұрын

@@letsMakeItFly If the auto pilot wasn't correct I have no doubt it had an effect in the erratic take off roll. However let's say for example that it was working correctly the elevator would still need to pitch the nose up to get the wing to have more effective lift. Being that the rear landing gear is basically the pivot point of rotation if the AOA of the wing is negative when the model is level on all gear the elevator is basically going to be fighting against that the farther aft the gear is from CG the more difficult for the elevator to overcome. If you extend the nose gear leg height enough that the wing is level with the ground/runway or slightly positive 1-2° perhaps autopilot or not you probably won't have to use any up elevator to get off the ground at first and lift off/rotation will happen at a lower speed and in a shorter distance. I mean I actually don't know from experience but I'm pretty sure that's what would happen.

@letsMakeItFly 19 күн бұрын

@brianhutchinson7863 I agree with you, ill be extending the nose gear for the next flight. The wing strike was what I was referring to in my previous comment and the autopilot. Stay tuned, well see if your theory is correct. I'm hoping mid September ill have another video up with a much nicer wing! (and taller nose wheel haha!)

@brianhutchinson7863 19 күн бұрын

@@letsMakeItFly good luck and if you're interested check out a model called Melusine. It's a 3D printed FPV-able platform. It's very reasonably priced and if nothing else (you don't print, build and fly it) it would be a good example to study and perhaps gain insights with. That and you'd be supporting a cause similar to your own.

@tylerwillging8074 21 күн бұрын

That takeoff was wild!

@letsMakeItFly 21 күн бұрын

Sure was. Had me sweating!

@jessicalloyd2218 21 күн бұрын

I’ve been waiting to see your next video! 😊 looks phenomenal and worth the wait!

@letsMakeItFly 21 күн бұрын

Hope you like it!

@TNT_FPV 21 күн бұрын

nice looking plane

@letsMakeItFly 21 күн бұрын

Thank you! Wish it flew as good as it looks 😜

@seanyfpv 28 күн бұрын

awesome build! turned out well. I relate so much to the desire of wanting a fully fpv plane that has landing gear and autonomous capability haha, soon I'll work on something like it soon.

@letsMakeItFly 25 күн бұрын

Thank you, hope you achieve it!

@LloydKiddos 3 ай бұрын

You did really good and is excited for your next airplane model and next video! 👍👏🎉

@letsMakeItFly 25 күн бұрын

Thank You!!! Stay tuned for the next video

@jblchannel2679 5 ай бұрын

i think you need a flight controller f4 and gps to easy lauch (autolauch mode)

@letsMakeItFly 25 күн бұрын

I have the cube orange flight controller installed in it but i do have the F405 Wing flight controller that ill be putting on a future airplane!